Removed door seal and corner baffles by hand (no tools required). Replaced same parts with minor tweaking to get proper alignment of new seal. Strongly recommended: remove dishwasher trays in order to get head and shoulders inside for proper view of seal placement.

Removed 7 screws holding "inner door" in place ( note: 2 bottom screws are different than the rest...keep separate).....remove rinse aid plug....press "tabs" inward to release rinse aid container. ( in this instance....the gasket had failed...which was "part" of the reason dishwasher was leaking during operation)

install new rinse aid container ...making sure that "trip arm" is positioned correctly........and press into place. ( Tabs should expand when container is properly positioned...creating a tight seal).....reuse old rinse aid filler plug.

Replace "inner door" cover....tighten screws.....

remove faulty tub corner baffles....place new ones in corresponding positions ( the baffles form a suction .....to stay in place....no adhesive needed)

Close door and operate as usual........no more leaks!

This is a super easy "no brainer"...that would have cost about half the price of a new dish washer ...had I hired a "professional" to do the repairs!!!!

I looked at the gasket for the door, and noticed that it was flattened out and also noticed that there were two other seals at the lower left and right corners that were also hard and flattened. I found the parts for my dishwasher on this site and ordered them. Once I received them, I removed the old ones. They just came right out, and I inserted the new ones in the same spot. It was then that I noticed that there is another gasket for the door, that goes at the bottom of the inside of the door. The gasket for the door goes all the way around the outside, except for about a 4 inch section at the bottom of the door, right in the middle. I realized that I probably needed to get a new one of those too, so I ordered that part. I am now waiting on that small, 4 inch door gasket.

Since i was not sure which gasket has failed, i replaced all 4 considering the age of the dishwasher,( 2 are corner baffles ). The only time i was scratching my head was installing the gasket insert. No one mentioned to overlap or not, so i did overlap and crossed my fingers. After several cycles there is no dripping so i guess overlapping about a 1/2 inch is the way to do it. And i would suggest cleaning the gasket groove in the bottom corners really good. Good luck, bill

Pulled out the old seals paying particular attention to their orientation. Cleaned the mounting areas and installed the new seals by hand.

This unit is more than 20 years old and is working just fine. Part Select made it easy to find what I needed and the parts arrived in two days.

I took the inner door panel off as described by others on this website, cleaned out all the gunk left by 27 yrs of use, and replaced the door gasket and tub baffles. A Phillips-head screwdriver was required to remove the door panel, but no tools were required to replace any of the parts I ordered. I didn't find it necessary to soak the door gasket in warm water as it was pretty flexible right out of the package. I recommend stretching the gasket slightly while pressing it into the groove, particularly around corners, or it will end up being too short at the end. The rinse aid tank had also been leaking Jet-Dry for a long time, so I cleaned that mess up as well and tried to replace the tank. Unfortunately, the new tank did not fit my model of dishwasher even though this website and GE's stated that it did. The shaft on the tank that pokes through the inner door panel to the inside of the dishwasher was too short because >2 mm of it was taken up by a thick rubber washer and a hard plastic collar (fused to the shaft to hold the washer in place) that had not been part of my original rinse aid tank. PartSelect was very good about refunding me for the incorrectly identified rinse aid tank and stated that they would contact GE about correcting this error on their website as well. I therefore cleaned up my original rinse aid tank, rinsing out all Jet-Dry residue inside it, and put it back into the inner door panel. I researched this part and found that GE has redesigned it twice since my dishwasher was manufactured in 1985 -- my original part is no longer available anywhere. So, I will just not use Jet-Dry and will maybe upgrade to a dishwasher powder that includes rinse agent (e.g., Cascade Complete). Replacing the gasket and tub baffles and cleaning up my original rinse aid tank stopped the leak for less than the cost of a repairman's service call and diagnosis fees -- it would have cost me 3X more if he had provided the parts and done the repairs! Replacing my dishwasher was out of the question as they do not make them like they used to (i.e., no microchips or motherboards to fail in a few years) -- this is the first problem I've had with my dishwasher in 27 years! As a side note, I also learned from my research that my front door panel insert is reversible. I was able to remove a side trim piece, slide out the panel, and turn it over so the color is now white rather than the outdated almond. It's like I have a brand new dishwasher that is ready to go for another 27 years.

The lower right and left tub baffles just slip in, no tools required. For the front door gasket; a) removed the backside of the front door by removing the door screws. You need to manipulate the front door latch to remove the panel. b) remove the existing gasket, replace with new gasket. The short 4" gasket was missing, which is why it was leaking in the first place. Replaced it with the new one. Reassembled and tested. Thanks to Parts-Select for a great experience, very well done site.

Remove old left and right corner tub baffles, make certain area where the new baffles are to be inserted is clean and free of any debris. Gently press new baffles in to each corner. Remove old gasket insert and replace with new. Tell wife the job was a three hour ordeal that require advanced skills to complete!

I opened the D/W door, used needle nose pliers to remove the old baffles. They come right out. I cleaned the area using paper towels and installed the new baffles. They just sit in the corners with nothing holding them. Simple job.

First I removed the old gasket and seals. I replaced the seals and had difficulty getting the gasket to seal at the bottom of the door. I had to remove the seven door screws and was able to manipulate the gasket. Do not lift the inside door cover too far, as the latch may become disengaged, thus creating another problem to repair. I did this repair myself (female).

I replaced the top filler tube. (The $65 price for the filler tube is outrageous. Glad I didn't have a service man fix it. With mark-up it would have cost me over $100 for a 3 foot plastic tube. Crazy!)

While I was add it, I replaced the corner tub baffles.

The hardest part was figuring out how to disassemble the door to replace the baffles and door gasket. No pictures or clues on the internet or my owners manual. I figured it out myself and the rest was a piece of cake. When the 7 screws were removed, the door liner lifted right out and new parts fit right in.

Replaced door seal, right and left corner seals. Piece of cake. A five minute job.

Thanks

Old baffles lift out and new ones installed - very easy

On the GE Pot Scrubber 1120 model you do not even need tools to replace the parts that we replaced. We just pulled the corner baffles out and cleaned the corners before placing the new baffles in. For the door gasket, we just pulled the old gasket out and put the new one in the track that the old one came out of. We didn't have to take any door screws out to replace the gasket at all. It was very easy to do and no more leaks. You will have to push against the door to get it closed tightly the first time you use it since the new gasket has not been flattened by use. I ordered the gasket insert and used it since we had it but for this model we didn't really need it. I would suggest not ordering one for this model.