GE/GE_Thumb/00114277i03.gif
See part 497 in the diagram
Replacing your General Electric Dishwasher Drain Solenoid Kit play video
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 12am EST

customerservice@partselect.com

Drain Solenoid Kit

★★★★★
★★★★★
4 Reviews
$57.76   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

 Fits your GSD3200G00WW!
 Fits your GSD3200G00WW!
PartSelect Number PS260117
Manufacturer Part Number WD21X10060
Manufactured by GE
Product Description

Drain Solenoid Kit Specifications

This kit includes the armature and linkage assembly.
How Buying OEM Parts Can Save You Time and Money play video

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Not draining | Leaking | Will not fill with water | Not cleaning dishes properly
This part works with the following products:
Dishwasher.
This part works with the following products:
General Electric, Kenmore, Hotpoint.
Part# WD21X10060 replaces these:
AP2039738, 271344, WD21X10060, WD21X10057, WD21X10064
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

7 questions answered by our experts.
    Sort by:
    Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
    Jack
    November 13, 2017
    Dishes are fair to poor on the clean side. Some water always in bottom of the floor that does not look clean and clear. It seams to go through the cycles ok
    For model number gsd2600g00cc
    Hi Jack, Thank you for the question. I suggest first checking the Impeller and Seal Kit. Make sure the impeller is intact and not damaged.Also check to make sure the Sump and the cover are clean and undamaged. Hope this helps!

    1 person found this helpful.

    Was this helpful?
    Thank you for voting!
    Ken
    February 22, 2018
    Dishwasher will fill but doesn't drain. What you turn the timer knob it doesn't make the distinctive clunk sound when it changes cycles. I'm thinking it is the timer has gone bad. Is this most likely the problem?
    For model number GSD2200G02WW
    Hi Ken, Thank you for your question. I would suggest testing your drain solenoid and your timer both. It could be either of those parts causing the issue. If they are both testing find however, you might have to look into your motor being the problem. I hope that helps. Good luck with your repair.

    1 person found this helpful.

    Was this helpful?
    Thank you for voting!
    Related Parts:
    Brock
    November 14, 2018
    My dishwasher is leaking where the drain solenoid kit attaches to the shaft. Is there a seal that is supposed to go around that shaft i believe that is where my water is coming from? Thank you the mod# 363.14779100.
    For model number 363.14779100
    Hello Brock, Thank you for the question. Checking the video and the parts diagrams, I am not showing a gasket or seal on the shaft. You may need to check the shaft to see if it is lose or wore down. Hope this helps, good luck with this repair!

    1 person found this helpful.

    Was this helpful?
    Thank you for voting!
    Dale
    July 23, 2019
    Hi, my dishwasher is not draining, l pulled out the piston and nut assembly, and the rubber plunger is quite worn. Do l need the complete assembly, or can l just replace the plunger? Second, l found the chopper loose in the drain . Do l have to pull out the whole motor assembly to attach it, or will my dishwasher run without it. Dale
    For model number Gsd4108x03ww
    Hello Dale, thank you for your question. Yes, it is best to replace the entire assembly, not just the plunger. I believe the whole motor assembly would have to be removed to reattach the chopper. The chopper is very important as it chops up the food residue for easy draining and filtering. I hope this helps!

    Was this helpful?
    Thank you for voting!
    Marion
    January 29, 2020
    Is this the same as a cycle solenoid? Only leaks when changing cycle?
    For model number GSD3800G00WW
    Hello Marion, Thank you for the question. If you have a leak when the appliance is switching cycles, it is suggest the Drain Solenoid Kit will need to be replaced. We hope this helps.

    Was this helpful?
    Thank you for voting!
    Bruce
    February 8, 2020
    Water is falling from the bottom of the drain solenoid as the pump empties the tub. Why?
    For model number GSD3960LOOSS
    Hi Bruce. There could be a leak in solenoid, it may need replacement. Thank you for your question and good luck with your repair.

    Was this helpful?
    Thank you for voting!
    Related Parts:
    Gary
    September 9, 2017
    How do i determine if the drain solenoid is working properly? As i turn the control knob through the cycle the solenoid activates, but doesn't seem to stay down long enough to drain. The problem i have is not filling with water. The float switch tests ok, float not stuck. Replaced the inlet valve which i thought was bad (tested at 1.15k ohm), but still no water. Water supply is good to the inlet valve.
    For model number adw1000k00bb
    Hello Gary, thank you for contacting us. Based on everything you have already tried, the drain solenoid kit would be the next step as this should fix the issue. Good luck with the repair!

    Was this helpful?
    Thank you for voting!
      Part Videos

      Replacing your General Electric Dishwasher Drain Solenoid Kit

      Replacing your General Electric Dishwasher Drain Solenoid Kit play video
      Customer Repair Stories
       Average Repair Rating: 3.8 / 5.0, 25 reviews. What's this?
      Sort by:
      Sorry, we couldn't find any existing installation instruction that matched.
      D/W would not drain. Water standing in bottom.
      It is a simple process to replace the drain solenoid on these dishwashers, having replaced several in the past few months.

      After removing the front bottom panels, I removed the 2 screws holding the old solenoid, unplugged the wire harness, and then switched over the springs to the new solenoid. Assembly was installing 2 screws, and plugging in the wire harness.

      I work on a 260 + unit property, as well as working for a property management company who rents single family homes.

      PartSelect.com is an excellent source of parts, shipping in a quick manner, allowing the repairs to be completed in a timely manner. Thank you.
      • Ed from Cornelius, NC
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        Less than 15 mins
      • Tools:
        Nutdriver, Screw drivers
      • Parts Used:
        WD21X10060
      62 of 68 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Dishwasher not draining
      Actually, the problem started with a Timer Motor failure, and that let the dishwasher run for 4 hours (doh!). Immediately, I tested and ordered the timer, which unfortunately didn't come as just a motor, it came as an assembly. I installed it, and the dishwasher ran the cycle just fine.

      Except it didn't drain.

      After poking around, I noticed the drain solenoid had apparently been overworked; the timer must have failed on DRAIN. The solenoid was severely overheated, and thankfully didn't cause a fire, but it was somewhat melted. Replaced the solenoid, and all is well, especially when my wife was eyeballing a $1000 Bosch!
      • Christopher from Woodbridge, VA
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        Less than 15 mins
      • Tools:
        Pliers
      • Parts Used:
        WD21X10060
      15 of 17 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      dishwasher didn't pump out water
      with electric power and water source turned off,I first bailed out the water from tub then I pulled dishwasher out from under cabinet . Then I removed the motor and pump and put it on the table. I took a digital photo so I could remember exactly how everything was assembled. I checked for clogs and damage and realized that the solonoid casing had melted around the armature link assembly . I Looked at diagram for parts name and number and ordered from parts select. In the meantime I put a temporary one feed valve on hot water feed line so I could have access to hot water in kitchen while I waited for parts wich were here in a couple of days. Put it all back and it runs fine. Thank for your help
      • stephen from griswold, CT
      • Difficulty Level:
        Easy
      • Total Repair Time:
        1- 2 hours
      • Tools:
        Nutdriver, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
      • Parts Used:
        WD21X10060, WD1X1316
      15 of 33 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Water not draining from dishwasher
      This is a great website. I ordered my part on Wednesday night and it arrived Saturday morning without paying any extra for shipping. Plus since I am a female, this website enabled me to easily and affordably make the repair myself without having to worry about a repair man trying to take advantage of someone that they think they can.

      I first made sure that there was nothing stuck in the drain area inside of the dishwasher. That meant I had to bail out all the standing water and then unscrew the mesh cover from the bottom. Since there was nothing in there I ordered a new solenoid.

      First I unplugged the dishwasher. Then I removed the screws with a screwdriver that held the bottom cover on the dishwasher. Once I could see the installed solenoid, I put together the pieces of the replacement solenoid that I bought so I was sure to install the new one correctly. That did not require any tools. Then I unscrewed the two screws that held the solenoid in place and removed the little metal ring from the shaft which was the last piece holding it in place. Getting that ring off was tricky. I ended up using a pair of tweezers to pull it off. After that I put the new part on and screwed it in with the two screws provided. The little metal ring went on much easier than the old one came off. I screwed the bottom cover back on and voila! my dishwasher was fixed.
      • Teresa from Livermore, CA
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Screw drivers, Socket set
      • Parts Used:
        WD21X10060
      12 of 12 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      dishwasher was not draining left water in bottom of machine the drain solenoid was melted.
      First I took out the two screws that hold the drain solenoid on the unit and took off the c- clip that held the arm on the shaft if you have a digital camera take a picture to make sure you can get it back together the same way.. Then put together new unit and attatched putting the c-clip back on. Ran it through some cycles to make sure the solenoid was working. Four days later the solenoid is melted again, the timer must have an intermittentant problem I should have replaced the timer and the soleniod both at the same time. Make sure you dont make the same mistake I did. Now I will be buying a new dishwasher instead of putting any more time and money into this one.
      • Eric from Golden, CO
      • Difficulty Level:
        Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Screw drivers
      • Parts Used:
        WD21X10060
      11 of 11 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Water would not drain.
      The washer ran through a full cycle, but the water didn't drain out. I pulled out the drain vent and checked for foreign objects. Also checked at the drain hose/disposal joint and there was no blockage. After removing the bottom panels I noticed the solenoid was shot. Cylinder was burnt up and stuck solid in the up position. I went online and found that a main cause of this can be from the timer causing the solenoid to over exert and burn out. I decided if I was going to order parts and dig into a repair I should replace both. For the timer it is just a matter of unscrewing the inner door panel and unplugging the old timer. Then inserting new one. Couple of things I ran into were the door is no longer heavy enough to stay down so I grabbed a waffle iron as a weight to hold it down. Also will need to unscrew the set screw on the Door lock latch's bottom side. Pay close attention to how it was together helps. For the solenoid I removed the main screws holding the unit in place as well as the c-clip holding the plastic arm. Undo the spring and plug and the whole unit comes out. Reverse these steps with the new solenoid to install.
      • Jay from North Liberty, IA
      • Difficulty Level:
        Easy
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Pliers, Screw drivers, Socket set
      • Parts Used:
        WD21X10155, WD21X10060
      10 of 14 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Water stays in the bottom because the solenoid burned out.
      It is pretty easy to replace the parts because the new and old parts are identical. I unplugged wire connection, removed the two screws and one small metal piece that fixes the plastic moving part, then put back with new parts.
      A little bit extra time may needed due to small space in that location, also the small or flexable screw driver is needed.
      • Guorong from Novi, MI
      • Difficulty Level:
        A Bit Difficult
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Pliers, Screw drivers
      • Parts Used:
        WD21X10060
      8 of 9 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      water wouldn't pump out
      The Solenoid black plastic had melted around the solenoid shaft. I unplugged the solenoid, removed 2 screws,then one C clip and pulled the the unit out. The new solenoid is difficult to install all together as the shaft it goes on holds it all together when both springs are installed - - so I installed in one piece, with the 2 screws, except for the white plastic thing, the C clip that holds it on the shaft, and one of the two springs - - these three items went on separately. I wanted to thank the help your expert gave, but I couldn't figure how to do that.
      • Anthony from huntington beach, CA
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Nutdriver, Pliers, Screw drivers
      • Parts Used:
        WD21X10060
      4 of 4 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Dishwasher would not drain
      According to instructions with part
      • Roberta from Bloomville, NY
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        Less than 15 mins
      • Tools:
        Screw drivers
      • Parts Used:
        WD21X10060
      4 of 6 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Water wasn't draining in the bottom of the dishwasher
      First of all this site is awesome. So helpful in diagnosing and ordering the part. I highly recommend!

      So, the solenoid was melted and needed to be replaced. If you're looking from the front of the dishwasher it's on the left side and it has 2 screws and a c ring. I couldn't get the c ring back on, but the piece stays on without it. Works fine now.
      • Drew from Charlotte, NC
      • Difficulty Level:
        A Bit Difficult
      • Total Repair Time:
        1- 2 hours
      • Tools:
        Pliers, Screw drivers
      • Parts Used:
        WD21X10060
      2 of 2 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Customer Reviews
      Average Rating:
      ★★★★★
      ★★★★★
      4 Reviews
      4.8
      Filter By Rating:
      • 5 Stars
        3
      • 4 Stars
        1
      • 3 Stars
        0
      • 2 Stars
        0
      • 1 Star
        0
        Sort by:
        Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
          Related Parts
          Model Cross Reference
          This part works with the following models:
          PartSelect Number: PS260117
          Manufacturer Part Number: WD21X10060
          Brand
          Model Number
          Description
          Kenmore
          36314031000
          Dishwasher
          Kenmore
          36314031001
          Dishwasher
          Kenmore
          36314032000
          Dishwasher
          Kenmore
          36314032001
          Dishwasher
          Kenmore
          36314038000
          Dishwasher
          Kenmore
          36314038001
          Dishwasher
          Kenmore
          36314039000
          Dishwasher
          Kenmore
          36314039001
          Dishwasher
          Kenmore
          36314071792
          Dishwasher
          Kenmore
          36314071793
          Dishwasher
          Kenmore
          36314071794
          Dishwasher
          Kenmore
          36314072793
          Dishwasher
          Kenmore
          36314072794
          Dishwasher
          Kenmore
          36314072795
          Dishwasher
          Kenmore
          36314074792
          Dishwasher
          Kenmore
          36314074793
          Dishwasher
          Kenmore
          36314074794
          Dishwasher
          Kenmore
          36314075792
          Dishwasher
          Kenmore
          36314075793
          Dishwasher
          Kenmore
          36314075794
          Dishwasher
          General Electric
          36314081991
          Dishwasher - DISHWASHER
          Kenmore
          36314081992
          Dishwasher
          Kenmore
          36314081993
          Dishwasher
          Kenmore
          36314081994
          Dishwasher
          Kenmore
          36314151000
          Dishwasher
          Kenmore
          36314152000
          Dishwasher
          Kenmore
          36314158000
          Dishwasher
          Kenmore
          36314159000
          Dishwasher
          Kenmore
          36314181200
          Dishwasher
          Kenmore
          36314181202
          Dishwasher

          Get in touch, we're here to help!

          Open until 1am EST

          Contact Customer Service