Sump Housing WD18X213 | Official GE Part | Fast Shipping | PartSelect
Sump Housing – Part Number: WD18X213
Sump Housing – Part Number: WD18X213 Sump Housing – Part Number: WD18X213 Sump Housing – Part Number: WD18X213 Sump Housing – Part Number: WD18X213 https://partselectcom.azureedge.net/Schematics/GE/00114277i03.gif

Sump Housing

Product Description

Sump Housing Specifications

This part is the replacement sump housing or sump insert for your dishwasher. It is made of plastic and is approximately 7 inches by 5 inches. The sump housing is attached to the bottom of the dishwasher tub and collects water for the pump. If your dishwasher is leaking, you may need to replace the sump housing. Be sure to disconnect the dishwasher from the water and power source before you begin this repair. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting

This part fixes the following symptoms:

Leaking

This part works with the following products:

Dishwasher.

This part works with the following brands:

General Electric, Kenmore, Hotpoint.

Part # WD18X213 replaces these:

2478, AP2039425, WD18X0201, WD18X0205, WD18X0213, WD18X201, WD18X205, WD18X218.
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer Repair Stories
Average Repair Rating: 3.1 / 5.0, 13 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Skott from Mason, OH
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Wrench set
Parts Used:
WD18X214, WD18X213, WD12X271
Dishwasher leaking at rubber connector - pump wash arm
First removed dishwaser from under counter so I could get to rubber connecter. It is located in center under dishwasher. I first needed to unscrew with wrench rubber connection at pump and and then the complete piece unscewed by hand from pump wash arm. I then just had to screw new rubber connector back on to bottom of dishwasher and re-attached at the pump. It was very easy to replace the rubber connector. I also replaced the dishwasher sump housing because it was made of same rubbber material and feared it was deteriorating also. I had to unscrew with wrench at pump as well and it just popped out from inside dishwasher after unscrewing screen inside dishwaser. Popped new piece in and screwed screen back on and reconnected underneath dishwasher back to pump. The rack roller wheel just popped right on. FYI: The wheel is actually 1.75 inches in diameter not 2 inches. I was worried it might be too big if it where 2 inches but it was the same size as the other wheels which was 1.75 inches. The hardest part of this job was getting the dishwasher in and out from under the counter. The good news is that most of these parts are standard and the replacement parts fit perfect.
82 of 144 people found this instruction helpful.
Was this instruction helpful to you?
David from East Greenwich, RI
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Parts Used:
WD18X213
Mice ate holes in the Sump housing
First shut off the Power and Water to Dishwasher, removed from under counter, removed sump screen and retaining clamp from sump housing and then loosened seal from inside dishwasher cavity. Upon removal I went in search of a replacement part and found Parts Select on the web, entered my model and make at there web site and found the part I needed, I could verify the size by the easy picture on a one inch tile background for the dimenision . I called in the order since I wanted overnight service, I received the part and after cleaning the area where it goes I proceded to put things back together, this took about a hour and a half and the dishwasher is back in service
15 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Alan from Rossville, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers, Socket set
Parts Used:
WD18X213
A house mouse tore through the rubber housing
I pulled the dishwasher out from under the counter. Loosened the collar holding the sump housing to the pump motor. Unscrewed the cover inside the base of dishwasher to release the collection opening of the sump. It's very flexible so I pulled it out by hand. Put the new one in and screwed everything back down. Pushed the dishwasher back under the counter. Simple Simple Simple.
7 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Beatrice from Medford, NY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Wrench set
Parts Used:
WD18X213
Dishwasher is 5 yrs old. Never really washed right sometimes had sand on the top rack. 1 month ago started leaking from bottom put towels down and did only 1 load a day. Floor starting to rot my husband pulled out the dishwasher saw where it was leaking took the piece out saw it was cracked and repl
Unscrewed 2 screws from under the counter, pulled out dishwasher. Saw where it was leaking. Took wires loose, took the rack out, unscrew the white mesh, took out the dishwasher sump housing product saw a crack and ordered the piece. For anyone out there make sure you turn the electric power switch off before you attempt to fix anything!!!!!!
7 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Timothy from Loves Park, IL
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Parts Used:
WD18X214, WD18X213
water leak due to bad rubber connector
Ordered rubber connector and it arrived the next day. Shut off main power and water. Disconnected water supply and pulled unit out from under counter. Flipped unit over on it's side. Disconnected wiring, drain hose, clamps and completely removed motor/pump. Rubber connector would not unscrew by hand so I found a drinking glass slightly smaller in diameter than the connector inner diameter. Inserted glass in connector and proceeded to unscrew connector by turning connector and glass together. After removing old connector I cleaned the mating part after removing it from inside the washer and removed all the build-up. Replaced everything back in same order.
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
sandra from colorado springs, CO
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Parts Used:
WD18X213
the sump housing was worn out and leaked
first I used a shop vac to clean any excess water left behind, removed the sump housing from the motor, removed the sump housing from the body of dishwasher, replaced the old housing for the new one and reversed my steps to remove old one,
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Georgina from Poplar Grove, IL
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Wrench set
Parts Used:
WD18X214, WD18X213
water leak
I shut off water and pulled dish washer out removed all water. Turned waasher upside down.
Removed sump housing screws and unscrewed
pc fitting ,replaced new parts. Make sure things are tight before turning on water.
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Joe Dale from Gilbert, WV
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Parts Used:
WD18X214, WD18X213
water leaking out of dishwasher,pump to washer arm split
First turn water supply off,take out two screws under counter that holds dishwasher in place,pull washer out just enough to take water supply line loose from the unit, finish pulling unit out from under the counter top lay unit on it`s side or door down on the floor,remove clamp with a flat screw driver,unthread pump connector from washer arm and install new connector, very easy installation if you have any mechanical skills at all.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Larry from Saint Johnsville, NY
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Wrench set
Parts Used:
WD18X213
mice chewed hole in sump housing
Removed dishwasher from under counter,hardest part,removed to workshop. Laid it on the door with cardboard under it. Removed the clamp with a nut driver, pulled it off the pump squeesed it up out of the tub. To replace it was a little harder. It didn't want to stay into the grove in the tub. Placed it on the pump first to hold it down and than it went in the grove better. Last I took a wooden dowell rod and press it down tight into the grove. Replaced drain guard which holds it into the grove. Tested it for leaks. Returned it to under counter.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Meredith from Charlestown, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Parts Used:
WD18X214, WD18X213
leaking
My dishwasher is just over two years old and began leaking, naturally, out of warranty. My son has been repairing appliances for many years and knew what to look for, which is why we ordered the parts. When I contacted " Hotpoint " and was told how sorry they were , the person I spoke with only implied that my son isn't qualified and they could send a technician " to look at it ". I told them not to bother, but to be assured, after buying Hotpoint appliances most of my life, I will look at other products in the future, that might last more than two years. As soon as the parts were replaced, the problem was resolved.
1 person found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
4 Reviews
5
out of 5
Filter By Rating:
  • 5 Stars
    4
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Stars
    0
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Model Cross Reference

This part works with the following models:

PartSelect Number: PS259557
Manufacturer Part Number: WD18X213
Brand
Model Number
Description
Kenmore
18385
Dishwasher - DISHWASHER
Kenmore
36.1402891
Dishwasher - Kenmore Dishwasher Model 36.1402891 (361402891, 36 1402891) Parts
Kenmore
363.14471792
Dishwasher - Kenmore Dishwasher Model 363.14471792 (36314471792, 363 14471792) Parts
Kenmore
363.14475792
Dishwasher - Kenmore Dishwasher Model 363.14475792 (36314475792, 363 14475792) Parts
Kenmore
363.14478793
Dishwasher - Kenmore Dishwasher Model 363.14478793 (36314478793, 363 14478793) Parts
Kenmore
363.1516790
Dishwasher - Kenmore Dishwasher Model 363.1516790 (3631516790, 363 1516790) Parts
Kenmore
363.GSD500P-49W
Dishwasher - Kenmore Dishwasher Model 363.GSD500P-49W (363GSD500P49W, 363 GSD500P 49W) Parts
Kenmore
3631401190
Dishwasher
Kenmore
3631401191
Dishwasher
Kenmore
3631401590
Dishwasher
Kenmore
3631401591
Dishwasher
Kenmore
3631401592
Dishwasher
Kenmore
3631401890
Dishwasher
Kenmore
3631401891
Dishwasher
Kenmore
3631401892
Dishwasher
Kenmore
3631402190
Dishwasher
Kenmore
3631402191
Dishwasher
Kenmore
3631402192
Dishwasher
Kenmore
3631402590
Dishwasher
Kenmore
3631402591
Dishwasher
Kenmore
3631402592
Dishwasher
Kenmore
3631402890
Dishwasher
Kenmore
3631402891
Dishwasher
Kenmore
3631402892
Dishwasher
Kenmore
36314031000
Dishwasher
Kenmore
36314031001
Dishwasher
Kenmore
36314032000
Dishwasher
Kenmore
36314032001
Dishwasher
Kenmore
36314038000
Dishwasher
Kenmore
36314038001
Dishwasher