Tub Gasket WD08X10018

Followed the instructions that came with the my order

changed the door gasket no tools,just pulled out the old,lined up the dot (printed on gasket)on the new and started at the top pushed in the new took five minute,the short bottom door seal required a phillips head screwdriver to remove the inside door screws(six screws) the two on the bottom are different they attach to the door hinge and are machine thread the other four are coarse thread.lifted off the panel slide off the old(pay attention to which way the curve goes) slide on the new replaced the panel put in the six screws.the job is done! the door will be tight to close but will be easier after a few uses.

No way to repair since the wrong part was sent. I have sent numerous emails with order numbers, part numbers, model numbers BUT I have no return label to send this back and get a refund. Maybe this will get someone's attention. Pretty disgusted!

I watched the parts select video and followed their instructions. Only “ issue” was there were no screws on the door behind the exterior skin as in the video, so lifting the inside door liner to put the new lower door seal in was concerning. I was able to pull the liner up enough and slid the seal in with no problem. The video was the key to a smooth repair.

I removed the old seal, cleaned behind it, and then put the new seal in. We saw a video on You Tube on how to do it. Partselect also sent instructions on a e mail with the order receipt. We enjoyed working with you guys. Your customer service representative was very nice and accurate in sending out the part. All went as she said it would. Thanks!!

The gaskets arrived in a few days after my order. The tub seal was easy to change and tool only a few minutes with no tools. After I watched a video on the GE website I pulled out the old gasket, wiped out the slot, centered the new gasket at the top, pushed it in the slot to each corner.Then I pulled the end to the end of the track and pushed it in the full side from the bottom up. repeated on the other side.The lower gasket was harder and took about 40 minutes. I took eh door apart but did not need to it could be done with a mirror. Pull the old one out from one side. Don't be afraid of tearing it but get it all out. The new one will snap into the slot if you use a mirror to look in the door and see.

Pulled out the old one put the new one in . Simple and easy

I removed the old gasket very easily as there wasn't even glue holding it in place. The new gasket just pressed right into a slot and makes a water tight seal.

1. Replacing the TUB GASKET is very easy and does not require tools. Pull out the old gasket and wipe out the channel. The gasket is marked with a small paint mark at the center and that indicates where to start at the top. The larger part of the gasket goes towards the outside. Firmly press the gasket all the way into the channel. The gasket should just reach the bottom of the tub. Do not use tools or you may damage the gasket. The gasket must be nearly all the way into the channel or the door will not close. Expect the door to close quite firmly for the first few uses.

2. Replacing the DOOR BOTTOM SHORT SEAL. This repair is not technically difficult, but is physically difficult. Without complete removal of the door, nothing needs to be or can be taken apart to do this replacement. I recommend removal of the lower basket, the upper basket and the wash arm before beginning. A drop light inside the tub is helpful. Using pliers or vise-grips grab the old seal and bend up and down then back and forth until it will slide all the way to one side. Once to one side use pliers to bent towards the back until its snap seal (observe new seal) realeases and you can carefully continue by hand to remove the seal the rest of the way across the bottom of the door. Observe how the old seal came out and which side was UP. With the new seal in hand, gently work the snap seal open slightly (this will help to get it back in place). With a flashlight and inspection mirror, check where the new seal will attach to (and clean if necessary). Center the new seal with the correct side up and work from one end. You may need pliers to push in the new seal, but be very careful not to damage the new bottom seal soft part. When it snaps in place you are done.

Installing the gasket took about 45 seconds. It actually took more time to scrub the area clean prior to installing. One quick trick I found was to fold the replacement gasket in two, and use that mark to center the gasket and press it in from there. That way you don't have any guesswork as to how much slack to allow for when starting.