Quick Question!

Have you ever purchased from PartSelect.com before?

258169-1-S-GE-WD01X10177        -Check Valve Flapper
258169-1-S-GE-WD01X10177        -Check Valve Flapper 258169-2-S-GE-WD01X10177        -Check Valve Flapper https://www.partselect.com/Schematics/GE/00114594i02.gif

Check Valve Flapper

Your Price

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS258169
Manufacturer Part Number WD01X10177
Manufactured by GE

This part works with the following brands: General Electric, Kenmore, Hotpoint.

This part works with the following products: Dishwasher.

This part fixes the following symptoms:

  • Not draining.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.0 / 5.0, 2 reviews What's this?
1-2 of 2

41 of 59 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: Aaron from Liberty Township, OH

Washing poorly, leaving particles of food on top of the dishes, not draining completely, ceiling spray arm not spinning (bent up to the ceiling)

The lower spray arm unscrews. From inside the dishwahser, put a screwdriver through the tab slots and unscrew the tower from the floor. It's pretty tight for plastic.
The upper spray arm has screws on the top of the dishwasher. You must slide the dishwasher out from underneath the countertop to get to the screws. Normally that's just the two screws above the door that screw into the countertop. Pull the insulation back and unscrew the arm from the top of the dishwasher. Reverse to reinstall.
Piston and nut assembly for check valve: Inside the dishwasher at the back there are 2 screws that hold a screen down. Remove the screen. Take out the check valve and replace it. It was still functional in mine, it looked like food gunk had built up on it and impeded the check valve action.
The flapper chec is a rubber flap in the drain tube that connects to your sink drain. You have to pull the dishwasher out from under the sink to get to the end of the drain tube that connects to the dishwasher. Take the hose clamp loose and remove the drain tube from the dishwasher. Then unscrew the plastic fitting that you just took the drain tube off of. The flapper chec is there. It had turned brittle and didn't flap anymore. It is a similar setup to the rubber seal at the end of your garden hose.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

7 of 9 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Murl from Hillsboro, MO

Dishwasher would not drain

First I looked for blockage and found none.I took the pump off and hooked power to it in my work shop and it did spin when powered up.We had broken a glass in the washer and thats when the problem started. I did find a few small pieces in the check valve assembly. It did not look bad but for cheap I ordered the part. Ran the washer and it drained on the wash but not on the final. Turned off the power.Slid the wash out where I could get to the power and not unhook the water. Turning off the power I disconnected the wires and carefully turned the power on and touched them to the pump and forced it to drain knowing that the pump worked I thought it would at least empty the water. I touched the wires to the pump and the board clicked the water drained. Hooked it back up. Ran it and has been working great since.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-2 of 2

Model Cross Reference

This part works with the following models:

PartSelect Number: PS258169
Manufacturer Part Number: WD01X10177
Brand Model Number Description