Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ann
September 16, 2019
My technician has replaced the body valve and draon check as well as the piston and nut assembly and the washer still has standing water in the bottom. He said that the drain soleoid and check flapper valve were okay as well as the pump. Is there any more that can be done. I had a plumber come to check it and the lines and air gap are free of clogs. What else can be done to trouble shoot the issue?
For model number GE GSD4260J00SS dishwasher
Hello Ann, thank you for inquiring. Besides the parts you have mentioned, you will want to consider the Water Inlet Valve, part number PS259368 for your model as the cause. Good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Customer Repair Stories
Average Repair Rating: 3.0 / 5.0, 2 reviews.
What's this?
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Washing poorly, leaving particles of food on top of the dishes, not draining completely, ceiling spray arm not spinning (bent up to the ceiling)
The lower spray arm unscrews. From inside the dishwahser, put a screwdriver through the tab slots and unscrew the tower from the floor. It's pretty tight for plastic. The upper spray arm has screws on the top of the dishwasher. You must slide the dishwasher out from underneath the countertop to get to the screws. Normally that's just the two screws above the door that screw into the countertop. Pull the insulation back and unscrew the arm from the top of the dishwasher. Reverse to reinstall. Piston and nut assembly for check valve: Inside the dishwasher at the back there are 2 screws that hold a screen down. Remove the screen. Take out the check valve and replace it. It was still functional in mine, it looked like food gunk had built up on it and impeded the check valve action. The flapper chec is a rubber flap in the drain tube that connects to your sink drain. You have to pull the dishwasher out from under the sink to get to the end of the drain tube that connects to the dishwasher. Take the hose clamp loose and remove the drain tube from the dishwasher. Then unscrew the plastic fitting that you just took the drain tube off of. The flapper chec is there. It had turned brittle and didn't flap anymore. It is a similar setup to the rubber seal at the end of your garden hose.
First I looked for blockage and found none.I took the pump off and hooked power to it in my work shop and it did spin when powered up.We had broken a glass in the washer and thats when the problem started. I did find a few small pieces in the check valve assembly. It did not look bad but for cheap I ordered the part. Ran the washer and it drained on the wash but not on the final. Turned off the power.Slid the wash out where I could get to the power and not unhook the water. Turning off the power I disconnected the wires and carefully turned the power on and touched them to the pump and forced it to drain knowing that the pump worked I thought it would at least empty the water. I touched the wires to the pump and the board clicked the water drained. Hooked it back up. Ran it and has been working great since.
With our Fix app model plate image recognition technology, we'll recommend the parts guaranteed to fit your appliance. Simply snap a photo, and we'll take care of the rest.
"I love love love this app. It's so nice to have useful information (receipts, manuals, parts lists, warranty info, pictures, etc.) on all of my household appliances and devices in one place."
You added to your cart
✖
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout