Quick Question!

Have you ever purchased from PartSelect.com before?

249285-1-S-GE-WB44T10010        -Bake Element - Push On Terminals - 240V
249285-1-S-GE-WB44T10010        -Bake Element - Push On Terminals - 240V 249285-2-S-GE-WB44T10010        -Bake Element - Push On Terminals - 240V 249285-3-S-GE-WB44T10010        -Bake Element - Push On Terminals - 240V https://www.partselect.com/Schematics/GE/00108750i03.gif

Bake Element - Push On Terminals - 240V

Your Price

$61.71
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS249285
Manufacturer Part Number WB44T10010
Manufactured by GE

This bake element is found on the bottom of the oven.

This part works with the following brands: General Electric, Kenmore.

This part works with the following products: Range.

This part fixes the following symptoms:

  • Little to no heat when baking.
  • Element will not heat.
  • Oven not heating evenly.
  • Will Not Start.
  • Oven is too hot.
  • Little to no heat when broiling.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Most Helpful

Question:

GE stove......when heating up the oven it announces that it is at the correct heat, such as 350, but is actually much lower. the digital readout says 350 but two thermometers show that it is about 200 degrees. i just received the new sensor (and a new light bulb) that i ordered from you last week. i have them installed and have tested the oven but find the same issue. i don't really want to change out the stove because the exterior is in great shape, not even a scratch on the top surface. does this sound like the element is failing?

Patrick for model number JBP67BH2CT
Answer:

Hi Patrick, Thank you for your question. Yes it does most likely sound like it is your bake element that you will need to replace however you may have to look into your control board. You can test your bake element with a multi-meter to test if it is not working correctly. I would also suggest taking a look at the gasket around your door, just to make sure that it's not worn down. If it has been worn, that could be the reason heat will not stay inside of your oven. Good luck with your repair. I hope this helps.

1 person found this helpful.

Most Recent

Question:

I am looking at the pictures of bottom oven element on your page for my GE electric stove. Mine does not heat up. I need the measurement of the one i am looking at. The measurement of mine is 17 3/4 inch wide, 12 inch long, 3 1/4 inch apart push in termimals. See if you have one with that measurement. Thank you

Delores Hagerman for model number J2B918BEK5BB
Answer:

Hi Delores, Thank you for your inquiry. The part number for the correct bake element for model number J2B918BEK5BB is PS249238. I hope this helps. Thank you and have a great day!

Question:

This model does not come up when i search. I need a bottom element for my spectra GE cooktop stove. I want to be sure to order the correct one. Please indicate which one works with my stove. Thank you. I am 77 and i need help.

Esther for model number JBP67BOD1WH
Answer:

Hi Esther, Thank you for your inquiry. GE sometimes removes the zeros from their model numbers so you would find the parts under JBP67BD1WH. The part number for the bake element from your appliance is PS249285. I hope this helps. Thank you and have a great day!

1 person found this helpful.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.4 / 5.0, 104 reviews What's this?
 

5 of 5 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers
Customer: John from West Lake, OH

Bottom element burned up and it was a little scary. Never seen this happen.

Un plug the power first.

Took the old element out and removed two nut holding the element in place. Remved back access panel on the back bottom of the unit. Disconnected wiring to part pulling the clip off of the connector.

Done fixed saved the house call.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 3 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Fran from East Wenatchee, WA 98802, WA

Oven baking element was burned out.

My husband actually did the replacement but I did all the research online to find the right part. I wasn't sure we'd find it for our old stove but luckily we did and it works fine. Thanks for the super fast service!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 3 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Pliers
Customer: Victoria from Bristol, FL

Oven element went out

Unplugged the oven, took out old element and replaced with new element. It was really simple and easy to do, didn't even need my husband who is not mechanically inclined.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 3 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Socket set
Customer: Mayree from Rocky Mount, VA

The bottom element would not come on

Took out the 2 screws,Pulled out the stove
Took the back off ,took the wires out of the little place where they fit in,Removed the old element.
Put the new one in Fitted the little thing which looked like a alumium flat piece back where we took the old one out.Put the back back on cut it on wheepe In business.Also the new element came here faster than I thought it would .I,m a 71 yearold grandmother.Pretty simple.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 3 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Linda from Ravenel, SC

Oven would not heat.

My stove would not heat. I could see that the bake element had a hole burned through it. Found this website. I was confused about what part I needed so I called the phone number and the girl was very good at locating exactly which element my stove needed after I gave her the stove make and model #. I ordered the part on Thursday afternoon. The part arrived on Saturday afternoon.

The hardest part of fixing it was finding the correct screw driver socket thingy (I'm not a technical person) to get the screws off with. Thankfully my neighbor had what I needed. I pulled my stove out from the wall (primarily because I needed to clean under there) and unplugged it. Unscrewed the screws, pulled the old element out until I could see the wire connections. I used clothes pins to hold the wires from going back into the stove once I unhooked them from the element (another tip I learned on this website) and simple slipped the wire connectors onto the new element, pushed it back into place, put the screws back on, plugged it in and TA DA... was baking a pizza in no time.

Very very VERY easy repair!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 3 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: STEVEN from FORT WAYNE, IN

Noticed that the lower heating element was flashing and popping. What looked like a welders arc went completely around the whole element and turned it to dust.

First I removed the two screws that hold the element in place. I then went to pull the element out and one of the wires touched the side of the access hole. There was a spark and the electrical breaker tripped. (Remember to always shut the electricity off first). Before I put the new element in I took off the access panel on the back of the range, slid in the new element, attached the two screwd that hold the element in place. Then I went around to the back of the range and re-connected the wires from that location to make sure there was nothing around the wires that would spark. Put the access plate back on and I was done.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Wrench (Adjustable)
Customer: Lloyd from Fishers, IN

Bootom heat element burned out

First I pull the stove out and unplug it. Than I removed the back cover by using an adjustable wrench. I unplug the element two wires. Then I opened up the oven on the stove and removed the racks and using the adjustable wrench remove the two bolts that mounted the heating elements. Replace with new element secured with bolts and connect the two wires to the heating element and put back on the back plate and plug the unit back into the wall.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Keith from glasgow, KY

Element burnt into pieces

Received part very quickly, easy to install, just give yourself enough wire on terminals when you pull them out, I let mine slip into holes they come out of and had to fish it out. EASY job.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Everett from Peachtree City, GA

The bake element was burned, it had a hole in it.

First , I have been working on electrical equipment for many years....and I forgot to un plug the unit from the wall. I assumed that if the oven was turned off I could remove the element, WRONG. One of the leads from the cord is wired directly to one lead of the element. When I tried to remove the element it shorted out against the wall of the oven. Then I turned the breaker off, unplugged the stove and finished the repair in about 10 minutes. Always unplug it first!.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: BRIAN from NEWARK, DE

Baking element broken

Baking element : Pull range away from wall. Disconnect the power. Remove back center panel. Remove range door. Remove range racks. Disconnect push on terminals fron baking element. Remove two hex head screws. Remove baking element. Reassemble in reverse order..........Temperature sensor: with back panel removed, unclip the electrical connector. Remove one hex head screw. Remove temperature sensor. Install in reverse order.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 5 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Socket set
Customer: Sondra from Henderson, TX

My element had went out

well first i came here thewn i called got my part the next day by the way paying only regular postage. it took me more time to pull the stove out and find the sockets then to actually put the element in.that took a whole 3 minutes. thanks partselect you guys are the best and i will be back.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 5 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Gayle from Bells, TX

My bake element actually caught on fire and broke in two.

First I removed the two screws that held the element in place. I then took the plate off the back of the range disconnected the two wires from the element and removed the old element. I then inserted the new element into the oven screwed the nuts back on and hooked the wires on the new element from the back put the plate back up on the back and screwed the nuts back on. It took around 15 minutes to do it all and this was the first time that I have ever done this. It was so easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Ronald from Houston, TX

Broken bake element

First I turned off breaker, pulled out oven unplugged/or dissconnected electricity to oven, unscrewed broken element in oven, unscrewed back panel of oven to disconnect 2 wires from element, and replaced with new element, then repeated the above in reverse.
Very easy for a typical DYI person.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: Mary from Lexington, KY

The bake element went crazy , caught fire and shot off sparks

We ordered the part, it arrived quickly my husband removed the burnt out element. We took the back off the stove in order to install the new part. It was easier to connect from the back than reach in to the oven. An easy repair and the stove works fine now.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
  • Bake Element - Push On Terminals - 240V
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: sherry from washington, ME

Baking element went up like a sparkler

removed the two screws,then pulled element out and removed the wires,took out element that needed replacing, then connected new element . the repair job took no time at all. i was really impressed with how easy it was.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

Model Cross Reference

This part works with the following models:

PartSelect Number: PS249285
Manufacturer Part Number: WB44T10010
Brand Model Number Description
Kenmore91192090300Range
Kenmore91192090301Range
Kenmore91192091300Range
Kenmore91192091301Range
Kenmore91192401990Range
Kenmore91192401991Range
Kenmore91192401992Range
Kenmore91192408990Range
Kenmore91192408991Range
Kenmore91192408992Range
Kenmore91192481990Range
Kenmore91192481991Range
Kenmore91192481992Range
Kenmore91192488990Range
Kenmore91192488991Range
Kenmore91192488992Range
Kenmore91192502990Range
Kenmore91192502991Range
Kenmore91192502992Range
Kenmore91192507990Range
Kenmore91192507991Range
Kenmore91192507992Range
Kenmore91192712020Range
Kenmore91192714020Range
Kenmore91192812300Range
Kenmore91192812301Range
Kenmore91192814300Range
Kenmore91192814301Range
Kenmore91193090300Range
Kenmore91193090301Range