Oven not heating evenly | Little to no heat when baking | Will Not Start
This part works with the following products:
Range.
This part works with the following products:
General Electric, Hotpoint.
Part# WB20K10027 replaces these:
AP4510147
Customer Reviews
Average Rating:
★★★★★
★★★★★
3 Reviews
5.0
Filter By Rating:
5 Stars
3
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Sandra J - September 28, 2021
Verified Purchase
Repair part
Installed part and it corrected issue.
★★★★★
★★★★★
Laurie B - August 20, 2020
Verified Purchase
Easy repair, part works perfectly!
The order was processed promptly and the sensor (which was shipped in protective packaging) arrived undamaged. Replacing the part was simple, and required only two nut drivers - one 1/4" tool and one amazing son.
I highly recommend PartSelect for product availability and excellent customer service!
★★★★★
★★★★★
LARRY C - March 7, 2018
Verified Purchase
Temp Sensor was the right one
This part worked out perfect and fairly eay to install.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 2.9 / 5.0, 5 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Replace temp sensor in gas range
Part came as ordered. Hardest part was fitting plastic wiring harness through the hole with 2 layers of steel with insulation in between. Used electrical tape to stiffen the end about an inch or 2 back from harness. Job done, problem solved
Ron from PAINESVILLE, OH
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gas Oven will not light
I was disappointed with this parts recommendation..neither part solved the problem, a first with partselect. The Range Oven sensor change out was easy and straight forward once the back lower panel was removed. The SPARK MODULE was time consuming..the module is located and accessible only by removing the range top. Having gas burners req
... Read moreuires unscrewing all the burners before tipping up the top and removing it, then removing the guard over the Module is next..it's a project, sure wish it worked when I was done!..turned out to be the oven glow bar....
un-screw temperature sensor, have to move racks and door, then open back cover board to disconnect the sensor.
George from LANSDALE, PA
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
3 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
8 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Lynn
September 17, 2019
Oven temp seemed low (was set at425 and display read likewise). Oven thermometer confirmed was only at about 250. Increased temp to see if it would go up. Overshot to 450 but display then said temp at only 380. Already know the igniter is going and already have that to replace, but wondered if this part may also be faulty since the display was not matching the actual temps in oven?
For model number JGC750EEF2ES
Hello Lynn, Thank you for the question. I suggest testing the Temperature Sensor. Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1000 – 1090 ohms at room temperature. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Chafia
January 26, 2020
I have GE gas range, it shuts off while baking, all the electric lights are off for about 40 min, then i have to restart again. I input the cooking time, it runs for about 15 min, then it shuts off. Please advice what can be the problem. By the way, it is a new range but i did not pay for a warranty when i bought it.
For model number JGB720SEJ4SS
Hello Chafia,
Thank you for your question. Our sources suggest replacing the electronic control board under part PS12296746 for your model to fix the oven issues. We hope this helps.
Is PS2374070 they correct part or should it be PS236490
For model number PCGB950SEF1SS
Hello Peter, Thank you for the question. This will depend on the length of the sensor in your appliance. The PartSelect Number: PS2374070 is about 7" long and the PartSelect Number: PS236490 is 2" long. We hope this helps!
I have trouble with the upper oven door lock, is it the temperature sensor or the door sensor? Light would not turn off after closing door and door lock light is on all the time.
For model number JGB850SEF1SS
Hi Victor,
Thank you for your question. If the light is on all the time, I would check the light assembly to verify if it is working correctly and then I would check the door latch. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Eva
May 15, 2019
I need a temperature sensor but not for an electric range. Mine is gas. Please help me find the right sensor
For model number Jgb500sep3ss
Hello Eva, thank you for your question. The sensor for the model number provided is PartSelect Number: PS2374070. Please enter the part number into the site for current price and availability. Good luck with your repair!
Was this helpful?
Thank you for voting!
Jim Lopez
September 2, 2019
Then oven on the range turn on but it keeps igniting every like 2 minutes i can see when it keeps turning on and off and does not reach correct temperature. Is that the sensor?
For model number JGB660SEJ4SS
Hello Jim, thank you for your question. The sensor would be the first part we would recommend testing. The temperature sensor WB20K10027 should read about 1100 ohms at about 70°F. You should thump it while testing to ensure no intermittent connection is present. If the sensor is not the issue, you may want to test the igniter next. I hope this helps!
Was this helpful?
Thank you for voting!
Nestor
December 15, 2021
Top oven ( not the bottom larger one) will be set at 400, and read 400( thought last 50 degrees a looooong time) but thermostat on rack reads 350. I set oven to 450(w/o turning off the current oven cycle) but thermostat still reads 350 even though oven will eventually read 450. Ohm reading between probes for top oven temp sensor reads 1090,
What should I check?
For model number jgb870sef2ss
Hello Nestor, thank you for writing. We recommend replacing the Temperature Sensor PS2374070. If this does not correct your issue then you need to consider the Electronic Control Board PS2374070. Good luck with your repair.
Top oven does not light. The igniter is not broken or burned. Appears it is not getting gas. I tried to light manually and nothing. The broiler does light on it's own and works properly. I am thinking oven sensor? Or any other ideas? Thanks.
For model number CGS990SET3SS
Hi Dale, thank you for reaching out. We have concluded that the issue is with the temperature sensor, part number PS2374070, which needs to be checked. If it is faulty, you may need to replace it. We hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
