GE/GE_Thumb/00125643i03.gif
See part 652 in the diagram
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 10PM EST

customerservice@partselect.com

RACK SLIDE END CAP

★★★★★
★★★★★
49 Reviews
$6.24   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS2370502
Manufacturer Part Number WD12X10304
Manufactured by GE
Product Description

RACK SLIDE END CAP Specifications

The Rack Slide End Cap is a white one-inch plastic part which replaces the end cap for your dishwasher rack, preventing your rack from sliding too far. If you find the dish rack is causing the door to not close properly, it may be due to the part being worn out or damaged. All you need to complete this repair is a small flat blade screw driver. Simply pop out the cap with a smaller flat-blade screwdriver and snap the new one into place. If the rear cap needs to be replaced you will need to remove both front caps and slide the rack completely off for full access. It is important to note that this part is sold individually, and more than one may be required, depending on your repair. An inexpensive part, it can be a good idea to purchase several at a time to have on-hand when needed.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Not cleaning dishes properly | Door latch failure | Door won’t close
This part works with the following products:
Dishwasher.
This part works with the following products:
General Electric, Hotpoint, Kenmore.
Part# WD12X10304 replaces these:
AP4484666, 1556527, WD12X0344, WD12X10238, WD12X344
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

8 questions answered by our experts.
    Sort by:
    Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
    Peggy
    July 20, 2017
    How do I remove the upper end cap …
    Hi Peggy, try using a smaller flat blade screwdriver to press in on the retainer clip. This is the small part that would be sticking out through the back of the metal rack slide. Once this has been pushed in, you should be able to pull it out by the end to remove it. I hope this helps!

    15 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Jimmy
    July 20, 2017
    I need to replace the right and left end cap on my top dishrack, is this what I need? Does the purchase come with one or two end caps and can I use this one for L and R?
    Hi Jimmy, yes this is the part you will need. This replacement end cap WD12X10304  can be used for the left or the right side. Only one will come with this purchase. Best of luck with this repair!

    7 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Tracey
    July 20, 2017
    I was able to get the end caps off but I cant get them back on. How do I reinstall the rack and caps?
    Hi Tracey, to reinstall simply press down on the retainer clip on the end caps WD12X10304 and push them into the slot until you hear them click into place on the railing. Please let us know if you have any further questions.

    2 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Scot
    February 8, 2019
    The soap is still in the soap compartment after the the dishwasher is done. It acts like no water is being used at all.
    For model number GSD6200J00CC
    Hello Scot, thank you for your question. If the soap isn't being released automatically the most likely issue is the dispenser itself. You would want to to replace the dispenser PartSelect Number: PS958966. Good luck with your repair!

    1 person found this helpful.

    Was this helpful?
    Thank you for voting!
    Alex
    February 18, 2019
    Machine has started making a roaring noise but only when spraying. It is still cleaning fine and drains properly. I have checked and cleaned a small amount of debris from the filters removed the spray arms and checked them, they are clean, flow freely, and spin freely. Any thoughts?
    For model number GLD4408R10BB
    Hello Alex, thank you for your question. It sounds like an issue with the circulation pump, PartSelect Number: PS1017766. I would recommend replacing that part. I hope this helps!

    1 person found this helpful.

    Was this helpful?
    Thank you for voting!
    Kelley
    February 3, 2020
    Do not know the model but i need the part that spins in the bottom and cleans the dishes.
    Hi Kelley. We would be happy to do some research to find you the correct parts. However, we need your model number and the brand name to locate any information on this. Model numbers can be short or long, and could have a mixture of numbers and letters. Thank you for your question and good luck with your repair.

    1 person found this helpful.

    Was this helpful?
    Thank you for voting!
    Alex
    February 18, 2019
    I asked a question earlier and it was suggested that the problem was with the circulation pump. How is this accessed on this model....need i pull it from under the counter and turn it over. thanks for your help.
    For model number GLD4408R10
    Hello Alex, thank you for your question. The circulation pump and motor, part number PartSelect Number PS3652479, can be accessed by pulling the dishwasher out and laying it on its back. I hope this helps!

    Was this helpful?
    Thank you for voting!
    Elaine
    December 23, 2019
    Soap dispenser door does not open to release soap when machine is started.
    For model number GDF520PGD1BB
    Hi Elaine, most likely replacing dispenser will fix this issue. Thank you for your question and good luck with your repair!

    Was this helpful?
    Thank you for voting!
    Related Parts:
      Part Videos

      Replacing your General Electric Dishwasher RACK SLIDE END CAP

      Customer Repair Stories
       Average Repair Rating: 4.5 / 5.0, 73 reviews. What's this?
      Sort by:
      Sorry, we couldn't find any existing installation instruction that matched.
      Worn/broken plastic parts were causing misery
      Order arrived two days after being placed. Super easy to remove the old, worn, broken plastic parts and replace with new. Everything popped right on just as shown in the diagram. Our happiness with our dishwasher has increased 100%. BTW, thanks to the very helpful, friendly and knowledgeable staff at PartSelect.com -- next job, replace the ice maker in the freezer!
      414 of 433 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      wheel replacement
      Pulled the end cap off and replaced the wheel.
      most of the parts were for future repairs
      229 of 430 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Parts were old and worn out
      The repair was easy. A couple turns of a screwdriver was all that was necessary to remove the rollers and slide assembly. The I simple installed the new rollers. Slid the slide into place between the rollers and then added the back caps to the slide. Replaced the rack rollers on the top basket and then slid it into position between the new slides. Once in place, I attached the end caps to the front of the slide. Simple and quick.
      29 of 40 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Top and bottom rack were rusted thru
      Bottom rack - slide the old one out, slide the new one in. The rack came came with the wheels, so I didn't use the replacement ones.
      Top rack - remove the rail end caps - they will likely break so order new ones. Slide the rack out. Remove the rotating spray arm and then remove all the brackets. I was able to re-use the old brackets and didn't need the replacements. Install the old brackets on the new rack, install the spray arm, and slide the new rack back into the rails. The new top rack also came with wheels installed, so I didn't use the replacement ones. Once the rack is back in the rails, install new rail end caps. Put them in sideways and facing into the washer. Straighten the caps and turn them into place. Be careful with the rail caps - they break easy and are expensive. Make sure they hold the top rack in place, and that's it.
      29 of 41 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Upper and lower racks starting to rust
      Removed the lower rack and upper rack after removing the end caps on the rail. Order new replacement end caps. The originals will likely break because the plastic becomes more brittle over time. Unsnap the upper washer arm from the original upper rack and snap onto the new one before inserting it into the rails.

      The trick is replacing the end caps. Using needle-nose pliers, bend the indented edge of the rails out so you can attached the new end caps without trouble. After they are in place, use the tip of the needle-nose pliers to restore the indentation on the edge of the rails to lock the caps in place.
      24 of 36 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      No Ice or water dispencing
      I first read about others with the same problem on your web sight and figured if they could do it so could I. Anyway the directions are a little hard to read but it was very informative and straight forward. I took the advice of one of the do it your-selfers when it came down to removing the spring. Be careful not to loose it. Everything was there that I needed and went on without a hitch. Now it was time to see if my repairs were done correctly. Pow! Everything worked. This is a great web-sight to buy parts if you are a do it your selfer. Easy to follow instructions.
      7 of 8 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      broken wheels and attachments
      Everything snapped on quite easily. I was releaved to not have to replace "everything."
      • Roger from Simi Valley, CA
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Pliers
      7 of 8 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Very, very easy. Took about 5 minutes. The end cap was on and working. And the repair company would charge $65 just to come out and look at it. It costs $9.00 to fix it. I am moving on to the refrigerator next. Very satisfied. Shipping is well worth the money. Ray D, Ansonia, CT
      Old cap was already off and had string on it. Cut the string. Placed end cap over. Used needle nose pliers to open metal rail a little and put in new cap. Locked right in. That was easy. Thanks again.
      • Raymond from ansonia, CT
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        Less than 15 mins
      • Tools:
        Pliers
      • Parts Used:
        WD12X10304
      7 of 9 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Dishwasher wouldn't drain completely
      Removed the dishwasher from the cabinet. Turned it on it's top side. Removed the exit hose from the pump with a nut driver and replaced the flapper. Reconnected the hose to the pump.
      • William from Nacogdoches, TX
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Nutdriver, Wrench set
      • Parts Used:
        WD01X10175, WD12X10304
      7 of 10 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      2 rollers and end caps were broken were broken
      Pulled the basket out the appliance and took what was left of the roller off and replaced them and slid the basket back onto the slide channel into the appliance. Then snapped the end caps on. Almost too simple. Less money than it costs to have the service man ring your door bell.
      • Robert from Old Lyme, CT
      • Difficulty Level:
        Easy
      • Total Repair Time:
        Less than 15 mins
      • Tools:
        Screw drivers
      • Parts Used:
        WD12X10327, WD12X10304
      6 of 7 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Customer Reviews
      Average Rating:
      ★★★★★
      ★★★★★
      49 Reviews
      4.8
      Filter By Rating:
      • 5 Stars
        41
      • 4 Stars
        6
      • 3 Stars
        1
      • 2 Stars
        0
      • 1 Star
        1
      Sort by:
      Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
      Model Cross Reference
      This part works with the following models:
      PartSelect Number: PS2370502
      Manufacturer Part Number: WD12X10304
      Brand
      Model Number
      Description
      General Electric
      1200L02
      Dishwasher - DISHWASHER
      Kenmore
      18385
      Dishwasher - DISHWASHER
      General Electric
      3000B10
      Dishwasher - DISHWASHER
      General Electric
      3000W10
      Dishwasher - DISHWASHER
      Kenmore
      361402891
      Dishwasher - Kenmore Dishwasher Model 36.1402891 (361402891, 36 1402891) Parts
      Kenmore
      3631401190
      Dishwasher
      Kenmore
      3631401191
      Dishwasher
      Kenmore
      3631401590
      Dishwasher
      Kenmore
      3631401591
      Dishwasher
      Kenmore
      3631401592
      Dishwasher
      Kenmore
      3631401890
      Dishwasher
      Kenmore
      3631401891
      Dishwasher
      Kenmore
      3631401892
      Dishwasher
      Kenmore
      3631402190
      Dishwasher
      Kenmore
      3631402191
      Dishwasher
      Kenmore
      3631402192
      Dishwasher
      Kenmore
      3631402590
      Dishwasher
      Kenmore
      3631402591
      Dishwasher
      Kenmore
      3631402592
      Dishwasher
      Kenmore
      3631402890
      Dishwasher
      Kenmore
      3631402891
      Dishwasher
      Kenmore
      3631402892
      Dishwasher
      Kenmore
      36314031000
      Dishwasher
      Kenmore
      36314031001
      Dishwasher
      Kenmore
      36314032000
      Dishwasher
      Kenmore
      36314032001
      Dishwasher
      Kenmore
      36314038000
      Dishwasher
      Kenmore
      36314038001
      Dishwasher
      Kenmore
      36314039000
      Dishwasher
      Kenmore
      36314039001
      Dishwasher

      Get in touch, we're here to help!

      Open until 10PM EST

      Contact Customer Service