Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jeff
August 15, 2017
Keypad is flashing " keypad maybe shorted and needs service" can i replace the keypad myself, and do you have the part. Jeff
For model number JVM1540DP1C
Hi Jeff,
Thank you for your inquiry. You should be able to install the assembly control panel with the touchpad part number PS2322065, yourself. If you need assistance in installing the part you may need to refer to your manual. I hope this helps. Thank you and have a great day!
6 people found this helpful.
Was this helpful?
Thank you for voting!
Darrett
February 14, 2018
Microwave will work sometimes than other times it will run for a few seconds and stop display will read excessive steam , then another time the display will read door not closed . Another time it will say reset clock. If unplugged for a little while then plugged back in it will work normal for awhile until the next error display. Was wondering if it would be the smart board
For model number JVM1740DP2BB
Hi Darrett,
Thank you for your question. It does sound like it could be your smart board. I would also suggest maybe testing the micro switches at your door just to check that they are working correctly. They should both be reading 0 ohms to be working correctly. I hope that helps. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Felix
August 19, 2019
Is the smartboard and keypad the same thing? If not what is the part # foe the keypad?
For model number JVM1540LP1CS
Hello Felix, Thank you for the question. The Keypad is part of the control panel PartSelect Number PS2322067 and does not include the Smart Board. Hope this helps!
Part number ps2370171. I can't get the ribbon cable to stay put in the clip. I put it in, but it doesn't seem to go in far enough and then when i lower the clip, it slips out easily.
For model number HVM1540LP1CS
Hi Tanya,
Thank you for your inquiry. When you install the ribbon, you should also push down the little locking tab that is on the board. That should secure the ribbon in place.
I hope that helps!
Was this helpful?
Thank you for voting!
Larry
December 12, 2019
Panel says keypad shorted do you have a part number for it and can i fix it.
For model number Jvm1540dp1ww
Hello Larry, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS2322066. Hope this helps!
All functions work, the vent will not turn on. Had to unplug to turn vent off
For model number Jvm1740dp1bb
Hi Doug,
Thank you for your question. If the vent will not turn on, there are some parts that you will need to check to see which ones are causing the issue. You will need to check the door switches, the light socket and the thermal fuse. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
Kamlesh
December 10, 2018
Who do i replace smart board to my microware it only work one side and aslo my refrigerator temperature is 25 to 30 and al my food refreezes the model no dfe29jsdass please let me know how i can bring the temperature to 37 degree i have already had some one come to fix it but it still does not work i have bought that only les than 6 years ago
For model number jvm1740sp2ss
Hello Kamlesh, thank you for your question. To replace the board, the top air grille would have to be removed, then the control panel would have to come off. There is a screw that holds the control panel to the unit that can be accessed from above. Once the control panel is removed, the board can be unplugged and the new one installed and the appliance reassembled. For the fridge, there could be a few issues. We would recommend replacing the Temperature sensor in the fridge, which is PartSelect Number PS304103. If the sensor has already been replaced, or is replaced and doesn't fix the issue you could have an issue with the control board or the compressor might be running too long. I hope this helps.
Was this helpful?
Thank you for voting!
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Customer Repair Stories
Average Repair Rating: 3.3 / 5.0, 1 reviews.
What's this?
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Dim readout on microwave display
The smart board has the display unit.
PULL THE POWER CORD PLUG
1. Remove the upper grill which is three screws across the top and slide the plastic vent piece to the left.
2. Remove control panel. Remove 2 screws on top of control panel. One is to the upper left and one is down inside the grill across the top. Slide the control panel up a small amount and pull top away from microwave.
3. Remove wire connections from the smart board and ground wire from the control panel. Some have clips to push to release.
4. Set control panel on table. Remove ribbon cable gently pulling it out of the plastic connection. Remove three screws holding smart board to the control panel and swap in the new one. Gently push the ribbon cable back into the plastic connector.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Linda T - 10 days ago
Verified Purchase
The exact part that I needed!
Easy install, microwave back up and running in no time!
★★★★★
★★★★★
Joey B - June 28, 2019
Verified Purchase
Smart Board
Do not need the board, I need the key pad. Found this out right before I received the board. The board was $100.00 and the key pad is $150.00. Do you have a deal to send back board in exchange for the key pad. Board has not been installed. I guess it's called a key pad, the numbers you push and the housing it's in. Thank you, Joey Bird
July 1, 2019
Hello Joey, Thank you for leaving a review on the part ordered. Checking the order I am showing you have already contacted us to address the issue. Please let us know if there is anything else we can assist you with.
★★★★★
★★★★★
Benny N - January 19, 2019
Verified Purchase
Easy repair,great part,worked as expected. Thanks to the microwave telling me what the problem was.
The part was well packaged,fast delivery. The Microwave was back in business within fifteen minutes. Thank you.
Model Cross Reference
This part works with the following models:
PartSelect Number: PS2370171
Manufacturer Part Number: WB27X11078
With our Fix app model plate image recognition technology, we'll recommend the parts guaranteed to fit your appliance. Simply snap a photo, and we'll take care of the rest.
"I love love love this app. It's so nice to have useful information (receipts, manuals, parts lists, warranty info, pictures, etc.) on all of my household appliances and devices in one place."
You added to your cart
✖
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
Stay on this site
Go to Canadian site
In Stock
