This authentic rear crisper support is a white, plastic part which is rated as "easy" to install by our customers. This OEM part replaces the rear crisper cover support in your fridge and mounts to the inside cabinet wall. If there is visible damager or your crisper stops fitting properly, it may be time to replace the part. Check your user manual and model number to ensure this part is what you need. Replacing the rear crisper support in your refrigerator is an easy job. This part is made from plastic and mounts on the inside of the wall. To complete this repair you will need a small putty knife, a punch or a short flat blade screwdriver, and a small hammer. You may need to replace your rear crisper support if you find that the door will not open or close. In order to complete this repair, you will need to remove all the shelves above the crisper in order to have ample room to work. It is also good to have duct tape on hand, which can be used to protect the liner around the support. This part is sold individually. Please note that the rear and front crisper support are different parts; this is the one you are looking for if it is your rear support that needs replacing.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Frigidaire Refrigerator Crisper Support - Rear
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
James P - March 10, 2024
Verified Purchase
Easy repair
The part fit as described.
★★★★★
★★★★★
Robert B - February 8, 2024
Verified Purchase
easy fix
part was easy to install
★★★★★
★★★★★
JOSEPH C - March 12, 2023
Verified Purchase
Easy repair!
It's only a simple piece of plastic but it's strong enough to support a heavy shelf!
★★★★★
★★★★★
Roy L - March 23, 2021
Verified Purchase
Crisper support - easy fix
I knew it was an easy fix. you Tubed it to see exactly what had to be done. Took longer to unload the shelf and crisper drawer than to swap out the broken part.
★★★★★
★★★★★
Jeffrey F - April 11, 2020
Verified Purchase
Exceeded my expectations !!!!!!!!!
Everything from finding the to ordering the part
To installing the the part was easy!!!!!!
★★★★★
★★★★★
Thomas M - November 18, 2019
Verified Purchase
It fit!
I wasn't quite sure how to remove the old part before installing the new. Just pulled out the old, put in the new, and it seemed like a perfect fit. It's been good for a few weeks now.
★★★★★
★★★★★
Kenneth B - June 14, 2019
Verified Purchase
Perfect fit to get my fridge back like new!
Love it!
★★★★★
★★★★★
Bradley R - June 4, 2019
Verified Purchase
easy peasy
with the video showing proper way to replace and ease of finding parts on this site you can't go wrong, have used website a number of times and see no need to shop somewhere else
★★★★★
★★★★★
Steven A - May 3, 2019
Verified Purchase
Easy repair if you do it right.
I tried prying the old support off with a putty knife and watched the fridge's plastic liner stretch out. You have to knock the old pin through the liner with the screwdriver or ice pick--the pin just falls behind the liner when you do that. Fortunately I stopped trying to use the putty knife before I disfigured the liner beyond usefulness. PUNCH FIRST, PRY SECOND!
★★★★★
★★★★★
Chris S - April 15, 2019
Verified Purchase
Worked as advertised
The diagrams on the site were very helpful in identifying the part I needed.
< Prev
1
2
Next >
Customer Repair Stories
Average Repair Rating: 4.4 / 5.0, 44 reviews.
What's this?
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Crisper cover support
Basically I just needed a crisper drawer cover w/o glass and the crisper support. I used a butter knife to remove old support clips and new ones snapped right in. Everything else was common sense
I followed the video and everything went smoothly. After pushing the pin in I pulled out the broken pin with needle nose pliers-very easy just like on the video. It took more time finding all the simple tools than the job itself-well almost!
Broken plastic guides on both crisper drawer covers. Upper crisper pan broken. Broken supports.
Remove both crisper pans and covers. Discard old frames and re-use glasses. Use two screw drivers to gently pry out broken supports. Top broken off smooth on one support. Unable to grasp with pliers to pull out. I drilled a small hole in the center of the large expansion pin. I screwed in a small sheet metal screw. Used side cutter pliers
... Read more to grasp screw and gently rock back and forth to remove center of large pin. Plucked out broken pieces with needle nosed pliers. Gently tap in expansion pins to install new supports. The rest is simple re-assembly using new parts. "Nothing to it but to do it."
Nothing exciting - just replaced the defective drawer covers with the new parts. The guides are poorly designed. the bottom guides on both covers failed.
I followed the excellent directions in the video linked to the email from PartSelect. The installation was quick and easy. I rated the whole operation "a bit difficult" because, if I had seen the video before I removed the old part, I would have known that you tap the support's center rod gently INTO the wall instead of wrestling it viole
... Read morently OFF the wall.
Read less
Neil from Lilburn, GA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken crisper drawer supports, cracked door shelf bins, broken freezer door handle.
My freezer door handle has been broken for probably 4 or 5 years - ex husband was not a handy man whatsoever. Never even thought to search for a replacement. Two door shelf bins were cracked and I had to be careful with how much weight I put in them. Then the crisper drawer support pegs broke. I couldn't do without that, so I finally s
... Read moreearched on line for replacement parts. This web site was so easy to use - detailed diagram left me with no doubt that I was ordering the correct parts. My order came within 4 or 5 days of my placing it! The parts were very simple to replace. I can't believe how long I waited. But $100 in parts has made me very happy!
My Frigidaire Drawer broke... I ordered the parts and installed it within 5 min. It took more time to remove the food and drawer then it did to install the pegs.
David from Coppell, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
5 of 18 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken shelf support
ordered the part, watched the video....it was a snap
Jerome from Hendersonville, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
0 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Crisper Supports broken
Removed supports with pliers and used center punch to push broken plugs out of hole and inserted the new supports.
GEORGE from ASHEVILLE, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench set
14 of 15 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
3
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jeffrey
December 18, 2019
This has the bottom crisper draw. The right front support has snapped of. Which support replaces this?
For model number 25352649301
Hello Jeffrey, thank you for your question. The front support for this unit is PartSelect Number: PS2358880. I hope this helps.
7 people found this helpful.
Was this helpful?
Thank you for voting!
Armand
July 2, 2019
I need front right clip for crisper drawer
For model number FFHS2622MB3
Hi Armand, thank you for your question. I have listed the part you are looking for below. Good luck with your repair.
What is piece called that goes into the side of the wall of the fridge that's hold the drawers up. It holds the bracket the drawers slide through
For model number FGHC2331PFCA
Hello Wilhelmina, thank you for your question. We have researched the model you have provided, and we would suggest the Crisper Support - Rear, part number PS2358879 and the Crisper Cover Support - Front part number PS2358880. We hope this helps!
Hi there,
I am looking for all 4 supports for the Vegetable/Fruit Fresh Lok Hydrator crisper for my fridge.
Make: FrigitaireModel: FRS23RYA
Are these 2 parts I need? If not, can you recommend the correct parts?
Crisper Support Rear $13.51
Part #: PS2358879
Crisper Cover Support $ 8.66
PS 2358880
Thank you so much for your time in helping me.
Cheryl
For model number FRS23R4A
Hello Cheryl, thank you for your question. We have researched the model you have provided, and we would suggest the Crisper Support - Rear, part number PS2358879 and the Crisper Cover Support - Front, part number PS2358880. We hope this helps!
