This authentic rear crisper support is a white, plastic part which is rated as "easy" to install by our customers. This OEM part replaces the rear crisper cover support in your fridge and mounts to the inside cabinet wall. If there is visible damager or your crisper stops fitting properly, it may be time to replace the part. Check your user manual and model number to ensure this part is what you need. Replacing the rear crisper support in your refrigerator is an easy job. This part is made from plastic and mounts on the inside of the wall. To complete this repair you will need a small putty knife, a punch or a short flat blade screwdriver, and a small hammer. You may need to replace your rear crisper support if you find that the door will not open or close. In order to complete this repair, you will need to remove all the shelves above the crisper in order to have ample room to work. It is also good to have duct tape on hand, which can be used to protect the liner around the support. This part is sold individually. Please note that the rear and front crisper support are different parts; this is the one you are looking for if it is your rear support that needs replacing.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jeffrey
December 18, 2019
This has the bottom crisper draw. The right front support has snapped of. Which support replaces this?
For model number 25352649301
Hello Jeffrey, thank you for your question. The front support for this unit is PartSelect Number: PS2358880. I hope this helps.
7 people found this helpful.
Was this helpful?
Thank you for voting!
Armand
July 2, 2019
I need front right clip for crisper drawer
For model number FFHS2622MB3
Hi Armand, thank you for your question. I have listed the part you are looking for below. Good luck with your repair.
What is piece called that goes into the side of the wall of the fridge that's hold the drawers up. It holds the bracket the drawers slide through
For model number FGHC2331PFCA
Hello Wilhelmina, thank you for your question. We have researched the model you have provided, and we would suggest the Crisper Support - Rear, part number PS2358879 and the Crisper Cover Support - Front part number PS2358880. We hope this helps!
Hi there,
I am looking for all 4 supports for the Vegetable/Fruit Fresh Lok Hydrator crisper for my fridge.
Make: FrigitaireModel: FRS23RYA
Are these 2 parts I need? If not, can you recommend the correct parts?
Crisper Support Rear $13.51
Part #: PS2358879
Crisper Cover Support $ 8.66
PS 2358880
Thank you so much for your time in helping me.
Cheryl
For model number FRS23R4A
Hello Cheryl, thank you for your question. We have researched the model you have provided, and we would suggest the Crisper Support - Rear, part number PS2358879 and the Crisper Cover Support - Front, part number PS2358880. We hope this helps!
Replacing your Frigidaire Refrigerator Crisper Support - Rear
Customer Repair Stories
Average Repair Rating: 4.4 / 5.0, 44 reviews.
What's this?
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Support studs were broken
Used pliers to remove the residual broken stud that was still attached to the wall of the refrigerator, and then just pushed the new part in place. The longest time was spent in removing the food and crisper drawers.
Refrigerator door bins cracked and glass shelf broke
Remove cracked bins, inserted new bins and replaced broken glass shelf. less than 10 minutes....parts came in 3 days.....website showed actual part pics which helped choose the correct replacement.......it was great!!
The 2 year old used the 2 bottom trays as a step stool
Repair was pretty straight forward. The Plastic around the glass cover of the crisper pan all broke where the stud holds it up. Replaced both of the plastic covers.
The broken support stud was a bit of a pain, you have to use a long nose pliers to try and pull the middle stud that locks everything in place. Forcing the entire support stud out will crack the plastic body of the fridge, so you have to truly find a way to get that middle stud out first to lose the clamps. Look at the new one you have and figure out how it works to give you an idea of how you can pull out the broken one.
All in all, was a pretty simple install. More annoying as you have a small space to work in.
I followed a gentleman's directions on your website, very useful I might add. It helped me replace all the broken parts with ease. I am a 33 year old mom of two. Anyone could do these repairs that I did. Thank you.
most importantly on the page with the necessary part..cripser support for the refrigerator--- there was a brief insructional video on how to properly dislodge the broken part and replace it with the new showing the simple tools needed. I am not handy at all but it took me all of two minutes thanks to the helpful video.
Broken plastic guides on both crisper drawer covers. Upper crisper pan broken. Broken supports.
Remove both crisper pans and covers. Discard old frames and re-use glasses. Use two screw drivers to gently pry out broken supports. Top broken off smooth on one support. Unable to grasp with pliers to pull out. I drilled a small hole in the center of the large expansion pin. I screwed in a small sheet metal screw. Used side cutter pliers to grasp screw and gently rock back and forth to remove center of large pin. Plucked out broken pieces with needle nosed pliers. Gently tap in expansion pins to install new supports. The rest is simple re-assembly using new parts. "Nothing to it but to do it."
The parts supplied were made to fit. The hardest part was getting the original broken tabs out of the internal walls of the fridge with out damaging the internal insulation. I punched the center locking pin through completely, dug out the broken tabs and then reached into the hole with a dental pick and pulled out the center pin. The new parts fit perfectly and with a plastic mallet, tapped the new locking pin into place.
The shelving brackets are install much like a blind rivet. I simply used a punch and gently pushed in the plastic center pin / mandrel. I then used a butter knife as a wedge to pull out the shelving supports enough to grab them with a pair of pliers. Simple to do!
I pulled out the old support stud with a pair of pliers, pushed the new stud in, and gave it a few taps with the hammer to secure it in the fridge wall. For the door bin I just slid the new bin in place.
Removed supports with pliers and used center punch to push broken plugs out of hole and inserted the new supports.
GEORGE from ASHEVILLE, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench set
14 of 15 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
3
Next >
Customer Reviews
Average Rating:
★★★★★
★★★★★
17 Reviews
4.7
Filter By Rating:
5 Stars
15
4 Stars
1
3 Stars
0
2 Stars
0
1 Star
1
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
JOSEPH C - March 12, 2023
Verified Purchase
Easy repair!
It's only a simple piece of plastic but it's strong enough to support a heavy shelf!
★★★★★
★★★★★
Roy L - March 23, 2021
Verified Purchase
Crisper support - easy fix
I knew it was an easy fix. you Tubed it to see exactly what had to be done. Took longer to unload the shelf and crisper drawer than to swap out the broken part.
★★★★★
★★★★★
Jeffrey F - April 11, 2020
Verified Purchase
Exceeded my expectations !!!!!!!!!
Everything from finding the to ordering the part
To installing the the part was easy!!!!!!
★★★★★
★★★★★
Thomas M - November 18, 2019
Verified Purchase
It fit!
I wasn't quite sure how to remove the old part before installing the new. Just pulled out the old, put in the new, and it seemed like a perfect fit. It's been good for a few weeks now.
★★★★★
★★★★★
Kenneth B - June 14, 2019
Verified Purchase
Perfect fit to get my fridge back like new!
Love it!
★★★★★
★★★★★
Bradley R - June 4, 2019
Verified Purchase
easy peasy
with the video showing proper way to replace and ease of finding parts on this site you can't go wrong, have used website a number of times and see no need to shop somewhere else
★★★★★
★★★★★
Steven A - May 3, 2019
Verified Purchase
Easy repair if you do it right.
I tried prying the old support off with a putty knife and watched the fridge's plastic liner stretch out. You have to knock the old pin through the liner with the screwdriver or ice pick--the pin just falls behind the liner when you do that. Fortunately I stopped trying to use the putty knife before I disfigured the liner beyond usefulness. PUNCH FIRST, PRY SECOND!
★★★★★
★★★★★
Chris S - April 15, 2019
Verified Purchase
Worked as advertised
The diagrams on the site were very helpful in identifying the part I needed.
★★★★★
★★★★★
Antonio C - February 25, 2019
Verified Purchase
Crisper support
This was the correct part and installation was easy . I will use this company again.
★★★★★
★★★★★
Jeffrey H - February 15, 2019
Verified Purchase
Part fits perfectly & arrived quickly
Part fits great; hardest part is getting the old piece extracted.
The Fix App makes it easy to manage all your stuff in one place. Just snap a photo and we'll find and store your user manuals, receipts, and product information in one easy-to-find place!
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff