Part Location Diagram of WH12X10412 GE Pressure Switch
See part 10 in the diagram
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.com

Pressure Switch WH12X10412

★★★★★
★★★★★
4 Reviews

Rated by 2 customers 

A Bit Difficult 

15 - 30 mins 

Ratings submitted by customers like you who bought this part.

$ 66.91
  Special Order
Get FREE EconoShip on orders over $100! T&C apply
PartSelect Number PS2354068
Manufacturer Part Number WH12X10412
Manufactured by GE
Product Description

Pressure Switch Specifications

This part is the replacement pressure switch, also known as the water-level pressure switch, for your washer. It is round and red on one side, and white with gold terminals on the other. The pressure switch senses and controls the water level in the washer. Once the washer has filled up to the appropriate level, it will allow the washer to move forward in the wash cycle. If it is defective, your washer will either not fill with water, or will not stop filling with water. Before you do this repair, be sure to disconnect your water from the power source, as well as the water source. This part is sold individually and is an OEM part from the manufacturer.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part works with the following products:
Washer.
This part works with the following products:
General Electric.
Part# WH12X10412 replaces these:
AP4412619
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
4 Reviews
4.0
Filter By Rating:
  • 5 Stars
    3
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    1
Sort by:
  • 1
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 3.3 / 5.0, 2 reviews. What's this?
Sort by:
  • 1
Sorry, we couldn't find any existing installation instruction that matched.
Washer was not filling completely up on super fill cycle
Removed control panel removed old pressure switch installed new switch replaced control panel plugged in washer.everything worked the way it is supposed to.
  • marvin from Flint, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water was not filling to correct levels
plugged on the wires and hase than snaped in place. the delay of the part was the hard part.
  • jon from grapvine, TX
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
25 of 68 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

23 questions answered by our experts.
Sort by:
  • 1
  • 2
  • 3
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Robert
September 11, 2017
Our washer will not fill to high level...what do we need to fix problem..?
For model number WPRE8150K2WT
PartSelect logo
Hi Robert, Thank you for the question. I suggest replacing the Pressure Switch. This switch detects the level of the water in the tub and tells the valve to stop filling. Hope this helps!

5 people found this helpful.

Was this helpful?
Thank you for voting!
Karen
September 14, 2017
Hi - my washer won't start/fill when the button is pushed. If I flip the switch to a different cycle, push the button again, flip, push, (many times) I can sometimes get it to start and then it's fine. Maybe the start button? I don't see that in the parts list though. I checked hoses and screens - they appear fine.
For model number GHWN4250D1WW
PartSelect logo
Hello Karen, Thank you for the great question. The start switch you need to replace is part of the Electronic Control Board,PartSelect Number PS8757105. The switch it built into the board and the board will need to be replace. Hope this helps!

5 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Stephen
March 20, 2018
The water is not filling up all the way i think do you know how high the water level is for a super load.I hate the auto fill can you help
For model number GTWN4250D0WS
PartSelect logo
Hi Stephen, Thank you for contacting us. Unfortunately we do not have that information about your appliance listed, for more specialized assistance or to speak with someone about this, I would suggest calling the manufacturer of the appliance directly. However the best parts to usually check when you are having fill issues are your water inlet valve, the pressure switch, and the hose for the pressure switch as well. With the hose you just have to look for any holes or breaks. Hope this helps!

3 people found this helpful.

Was this helpful?
Thank you for voting!
FRANK
October 8, 2021
How do I replace the pressure switch & hose
For model number GTWN4250D1WS
PartSelect logo
Hi Frank, Thank you for your question. Here is a link to one of our YouTube videos that you may reference on how to install the water level pressure switch, https://www.youtube.com/watch?v=t_3WfRff41E. The washer in the video may appear different from yours, but it will give you a general idea on how to install the part. We hope this helps! Good luck with the repair!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Mike
January 30, 2020
My washer will fill and wash, drain and spin, but only fill about an inch on rinse then immediately drains and spins a couple minutes then starts to fill again then drains and spins, does this on all rinse cycles on machine
For model number GTWN4250D1WS
PartSelect logo
Hello Mike, Thank you for contacting us. The new washers use significantly less water than the older versions so most likely the water level is correct.. The water level should completely saturate the clothing but it will not fill up to the top or even half way full. If you think that it's still too low then below is a link to the pressure switch inside the control panel that controls the water level and it would need to be replaced. I hope this helps.

2 people found this helpful.

Was this helpful?
Thank you for voting!
Pau
May 1, 2018
When i select "hot" for the water temperature, the water starts to fill in the washer and then shuts off after 30 seconds. Then it starts filling the washer with cold water. I tried turning the cold water off from the intake valve. It stops the cold water, but it still will not fill with hot water.
For model number GCWN4950D1WS
PartSelect logo
Hello Pau, thank you for your question. There are a few parts to test to determine what the issue is with this appliance. We would recommend testing the water valve itself, the temperature sensor, and the control board. I hope this helps!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Joyce
July 15, 2019
I was not getting enough water into the machine if I put it on a large super load. I did buy the pressure switch and it has not changed. It only fills small level loads.
For model number GTWN4250D0WS
PartSelect logo
Hi Joyce, Thank you for your question. If the washer is not filling the washer completely and you have already replaced the pressure switch, you will need to check the lid switch and the water inlet valve. I hope this helps. Thank you and have a great day!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Keith
January 2, 2018
My machine wont start or fill. Tried different settings and still unable to get it to start. I have checked for power and i have power from the outlet but not even a light at the machine. Do you think it could be my "main board" that has gone out?
For model number GTWN4250D2WS
PartSelect logo
Hello Keith, Thank you for your inquiry. You can test the control board with a multimeter to see if it has continuity. If it does, I would check the power cord, the lid switch, the pressure switch and the water inlet valve. If you are unfamiliar with how a multimeter functions, there are YouTube videos available to assist you. Hope this helps!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Lamar
November 12, 2017
My washer fills with water when the washer is not on
For model number WPRE6150K1WT
PartSelect logo
Hi Lamar, Thank you for the question. When water is dripping back into the appliance when the appliance is not in use, this indicates the Water Valve,PartSelect Number PS2354072 will need to be replaced. Hope this helps!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Steve
March 5, 2020
Is there a way to test my pressure switch or do I have to buy parts and hope that they are bad.
For model number GTWN4250D1WS
PartSelect logo
Hello Steve, Thank you for the question. To test the switch for continuity, use a multimeter, set at OHMS x 1. Touch the meter probes to terminals 1 and 2. It should be infinity (infinity, which means no continuity) or some value close to 0.0 continuity. We hope this helps.

1 person found this helpful.

Was this helpful?
Thank you for voting!
  • 1
  • 2
  • 3
You May Also Need ?
Model Cross Reference
This part works with the following models:
PartSelect Number: PS2354068
Manufacturer Part Number: WH12X10412
Brand
Model Number
Description
General Electric
GCWN4950D0WS
Washer
General Electric
GCWN4950D1WS
Washer
General Electric
GCWN4950D2WS
Washer - WASHER
General Electric
GCWN5050M0WS
Washer
General Electric
GCWN5050M1WS
Washer
General Electric
GHWN4250D0WW
Washer
General Electric
GHWN4250D1WW
Washer
General Electric
GHWN4250D2WW
Washer - WASHER
General Electric
GLWN5050M0WS
Washer
General Electric
GLWN5050M1WS
Washer
General Electric
GMAN4250F0WS
Washer
General Electric
GMAN4250F1WS
Washer
General Electric
GPRE8350K0WT
Washer
General Electric
GPRE8350K2WT
Washer
General Electric
GPRE8350K3WT
Washer
General Electric
GRWN5150M0WS
Washer
General Electric
GRWN5150M1WS
Washer
General Electric
GTAN4250D0WW
Washer
General Electric
GTAN4250D1WW
Washer
General Electric
GTAN4250D2WW
Washer - WASHER
General Electric
GTAN4250M0WS
Washer
General Electric
GTAN4250M1WS
Washer
General Electric
GTAN4450M0WS
Washer
General Electric
GTAN4450M1WS
Washer
General Electric
GTAN5050M0WS
Washer
General Electric
GTAN5050M1WS
Washer
General Electric
GTAP2250D0WW
Washer - WASHER
General Electric
GTAP2250D1WW
Washer - WASHER
General Electric
GTWN4250D0WS
Washer
General Electric
GTWN4250D1WS
Washer
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service