See part F3 in the diagram
( Grid squares measure 1x1 inch )
Control Board With Selector
$
168.72
Special Order
Special Order
Get this part fast. Average delivery time via standard shipping: 1.8 days.
PartSelect Number PS2352995
Manufacturer Part Number 154712101
Manufactured by
Frigidaire
Product Description
Control Board With Selector Specifications
This is a 4-button board. This part would be the main "brains" of the appliance which is activated by selecting a certain function with the touchpad.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Will Not Start
This part works with the following products:
Dishwasher.
This part works with the following products:
Kenmore, Frigidaire.
Part# 154712101 replaces these:
AP4392629, 1483317, 154712101, 154547701, 154568401, 154642301, 154668901
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Anne
January 9, 2018
The light that lights for dishes clean stays lit constantly. Because it won't shut off, the dishwasher will not start. Should this control board solve my problem?
For model number FDB1050RES5
Hi Anne, Thank you for the question. The Clean light will come on at end of cycle and remain on until door is opened. It sounds like an issue with the door switch. The door switch open and "break" the circuit when the door is opened or the Clean light will not turn off. You can try to disconnect power to the appliance to see if it resets the switch. If the issues continues, the Door Latch and Handle Assembly with Switches may need to be replaced. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Oxana
March 28, 2018
Dishwasher does not start. All control lights are lighting up, when pressed (except for start button). Was trying to reset, turning off the power, with no effect. Local repairman told me need to change control board. Your suggestion?
For model number FDB1050REC2
Hi Oxana, Thank you for the question. Yes, if none of the functions work I suggest replacing the Control Board, Part Number: PS2352995. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Ken
October 1, 2019
Can i get the main control knob and switch or is it all one part with the 4 buttons? To turn on the dishwasher, i have to turn the main round control knob that sets the wash cycle (quick, normal, heavy etc) several times. Then start it.
For model number 587.15188402
Hello Ken, thank you for inquiring. You will need this Control Board With Selector, part number PS2352995 for your model. The Knob is sold separate as part number PS1148931. Good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Leo
October 17, 2019
The only button I press that shows the red light and works is the drain button. When I press any other button ie., wash etc no lights or systems work. Any ideas?
For model number 6657798
Hello Leo, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the Full model number of the unit. 6657798 is incomplete. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Alex
November 23, 2019
My dishwasher stop working. No lights on display! I unplug and still no lights
For model number FDB1050REM2
Hi Alex, most likely cause is a faulty control board or wiring harness. Thank you for your question and good luck with your repair!
Was this helpful?
Thank you for voting!
Related Parts:
Matt
January 29, 2020
Washer clean light stays on, already changed the door latch switch still not working. Could be the control board?
For model number FDB1050REC0
Hi Matt, thank you for your question. It sounds like it. One thing that you can do is unplug your appliance for about 10 minutes. If you plug it back in and continue getting that error, then it is likely your control board that is the issue. Good luck with your repair.
Was this helpful?
Thank you for voting!
James
February 4, 2019
Washer fills with water when you press start, then it just sits there for several minutes after which it will drain, it's skipping the wash cycle but the drain pump and fill valve are working.
For model number FDB1050RES1
Hello James, Thank you for contacting us! I suggest checking the following parts: PS3501031 Pump/Motor Kit with Harness, and PS2352995 Control Board With Selector. Good luck with your repair!
Was this helpful?
Thank you for voting!
Chuck
September 16, 2019
Replaced control board but a resister was burnt lights on but will not start.
For model number fdb1050oec2
Hello Chuck, thank you for contacting us. The most likely cause of your dishwasher not starting is due to a faulty Handle and Latch Assembly with Switches, part number PS6448153 for your model. You may also want to consider the Pump/Motor Kit with Harness, part number PS3501031 as the cause. Good luck with your repair!
Was this helpful?
Thank you for voting!
Customer Repair Stories
Average Repair Rating: 4.2 / 5.0, 4 reviews.
What's this?
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Drain Motor would not run
I remove the 5 or 6 screws that hold the plastic decorative top front cover in place (the screws are on the inside of the door). Lifted and pulled the cover off of the door. Pushing in the two side clips, detached the control module power/control connector from the door. Removed two screws that hold the control module to the cover, then released the snapping clips that hold the control model in place. Reversed all the steps and ran a test cycle. It worked! Thanks PS!
-
Jonathan from Stamford, CT -
Difficulty Level:Easy -
Total Repair Time:Less than 15 mins -
Tools:Screw drivers -
Parts Used:154712101
16 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher wouldn't start, then became stuck in a cycle.
Pull the control knob straight out. Remove the screws along the top of the door, and the top two along the side near the top. The whole control panel will then fall away.
Unplug the old plug by squeezing the tabs and pulling.
Remove the two short screws that hold the control board to the plastic panel. After that, the board is still tightly held in place by a series of snaps around the perimeter. Most come free with a little work with a flathead screwdriver. The tough ones are underneath -- flip the whole plastic panel over to find an access for those.
Snap the new controller in place, install the two screws. Plug the wires back in (it is keyed and will only plug in the correct way). Put all the screws back in and you're ready to test.
The very first test I ran did not go well -- the dishwasher thought it was full of water when it wasn't. You may need to cancel the first cycle and start a fresh new cycle.
Unplug the old plug by squeezing the tabs and pulling.
Remove the two short screws that hold the control board to the plastic panel. After that, the board is still tightly held in place by a series of snaps around the perimeter. Most come free with a little work with a flathead screwdriver. The tough ones are underneath -- flip the whole plastic panel over to find an access for those.
Snap the new controller in place, install the two screws. Plug the wires back in (it is keyed and will only plug in the correct way). Put all the screws back in and you're ready to test.
The very first test I ran did not go well -- the dishwasher thought it was full of water when it wasn't. You may need to cancel the first cycle and start a fresh new cycle.
-
Mary Lou from Evans, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
-
Parts Used:154712101
12 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer would not start cycle proper.
Removed 5 screws unplugged wire harness removed control module and replaced.
-
Ted from Montague, NJ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
-
Parts Used:154712101
9 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Control board light stayed on green but the washer wouldn’t activate .
I opened this dishwasher and removed the 8 Phillip head screws, which separate the front panel which gives access to the control board. I then removed the 2 screws that holds the Control board into place,and removed the control board from the snap on harness. Then reverse the process by snapping in the new control board and replacing all screws and reattaching the face place. Run the washer through a cycle to make sure the new board would complete a full cycle. I thought it would be hard to do. But it was a piece of cake. Was only out of pocket for the board(132.00). Saved $125 by doing it myself. DIY (1), servicemen (0).????
-
NC from JACKSON, MS
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
-
Parts Used:154712101
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer Reviews
Filter By Rating:
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Hillary J - August 11, 2018
Easy repair-great condition.
The part was in perfect condition and was easy to install. My appliance is in working order! The purchase was just as easy and it arrived on time if not earlier.
Gary J - June 13, 2018
dishwasher burntsmell
This part fixed the problem. Worked great
Spencer W - February 27, 2018
Good part
The part worked like advertised
Model Cross Reference
This part works with the following models:
PartSelect Number: PS2352995
Manufacturer Part Number: 154712101
Manufacturer Part Number: 154712101
Brand
Model Number
Description