Halogen Light Bulb - 120V 20W WB25X10019 | Official GE Part | Fast Shipping | PartSelect
Our response to COVID-19
We're open and continuing to ship packages. Learn about our response to COVID-19
Halogen Light Bulb - 120V 20W – Part Number: WB25X10019
Halogen Light Bulb - 120V 20W – Part Number: WB25X10019 https://partselectcom.azureedge.net/Schematics/GE/00115320i02.gif

Halogen Light Bulb - 120V 20W

PartSelect Number PS2351821

Manufacturer Part Number WB25X10019

Manufactured by GE

Product Description

Halogen Light Bulb - 120V 20W Specifications

This light bulb is located on the inside of your microwave. The bulb is behind the top grill. It will need to be replaced when it has burnt out and no longer works. Unplug the unit before beginning this repair. Remove the top grill of your microwave, use your screwdriver to open the light socket, scrape off any silicone holding the bulb in place, clean the area of any oil and dirt, insert the new bulb into the socket without touching the bulb, slide the holder back into place, line up the tabs on top of the metal plate, and secure the holder back into place.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting

This part works with the following products:

Microwave, Microwave Oven Combo.

This part works with the following brands:

General Electric, Kenmore, Hotpoint.

Part # WB25X10019 replaces these:

1472843, AP4380308, WB08X10050, WB25X10019, WB36X10246, WB36X10344.
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Part Videos

Replacing your General Electric Microwave Halogen Light Bulb - 120V 20W

Customer Repair Stories
Average Repair Rating: 4.5 / 5.0, 36 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Mark from GRAND BLANC, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Parts Used:
WB25X10019, WB36X10071
Lens cracked and bulbs burned out
First I removed the single screw holding the lens assembly in place. Then I lowered the assembly and tilted it until it came out. To remove the existing cracked glass lens there were four tabs bent down on it. By hand I lifted each tab just enough to remove the broken lens. I then replaced the broken lens with the new one and re-bent the tabs down by hand to secure them to the new lens.

The lens assembly, now removed, revealed the cavity that contained the two halogen bulbs. Since they were both burned out for days, they weren't hot so I could pull each one out by hand. The bulbs are secured by two straight heavy gauge wire leads and provided a little resistance but come out fairly easily. Make a mental note of the angle they came out so it will be easier to replace them with new ones.

You're not supposed to touch halogen bulbs with your bare hands, so I used the bubble wrap they came in as a means to hold the bulb while installing it.

Be sure to insert the bulbs at the same angle they came out so the pins do not get bent.

Once both bulbs are in place, replace the lens cover assembly by putting the end opposite where the screw hole goes in first on the right, then swing it up until flush and screw it down.
212 of 291 people found this instruction helpful.
Was this instruction helpful to you?
Barbara from Littleton, CO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Parts Used:
WB25X10019, WD35X21041, WD35X21041, WB06X10288
none
I had no troubles!

Thank you...
85 of 161 people found this instruction helpful.
Was this instruction helpful to you?
Robert from Naples, ME
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
WB25X10019
Under the vent light bulbs needed to be replaced
Turned of f the circuit breaker to the microwave. Unscrewed the cover (1 screw!) popped out the old bulbs and plugged in the new ones, using the bubblewrap as a handle to be sure my skin didn't touch the light bulbs so the oil from my hands didn't damage or shorten the life of the new bulbs. Turned the circuit back on. That's it!
56 of 76 people found this instruction helpful.
Was this instruction helpful to you?
Walter from Midvale, UT
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Parts Used:
WB25X10019
This lamp does not have easy access
This is the second time that this lamp hase gone out. It is located in a small space in the top of the microwave and you need to remove the top front pannel, then take a screw or two out of a metal shield and bend the shield up to get your hand into the compartment where, if you know how, you can reach in and lift out the reflector shield that the lighbulb is plugged into and remove the old one and plug in the new one. The first time was hard to figure out how to do it but the second time wasn't bad because I knew how to do it.
31 of 50 people found this instruction helpful.
Was this instruction helpful to you?
Thomas from Wake Forest, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
WB25X10019
halogen bulb burned out
*Remove Two Phillips head screws from the top of vent slide the vent left to remove it. Take the charcoal filter out then the metal cover underneath the filter. It also has a phillips head screw. bulb socket is on right facing down. Squeeze the metal clips and remove socket from bracket. Installation is the reverse of removal.
22 of 27 people found this instruction helpful.
Was this instruction helpful to you?
Jerry from Rio Vista, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
WB25X10019
Two counter light bulbs burned out
After removing the screws holding the 2 cover plates in position, I removed the halogen light bulbs with my fingers. Then I placed a paper towel around the first replacement bulb and lined up the two wire connectors with the two holes in the receptacle. I pushed in, but the bulb's probes did not slide into the receptacle. I spent five minutes aligning and pushing but to no avail. Then I removed the filter screen on the side of the receptacle, shined a flashlight beam on the receptacle, and with an improved view of the two holes in the receptacle, slid the bulb in. The second bulb was inserted in a few minutes, and the job was done. Whoever designed the halogen bulb was not as bright as Thomas Edison.
16 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Robert D. from Knoxville, TN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Parts Used:
WB25X10019, 218359601
The plastic kickplate which conceals the evaporator coils had broken one of the four plastic snap-in connectors, allowing the kickplate to droop down upon the right side creating an unsightly appliance appearence.
Although a fine refigerator from a performance standpoint, a drooping evaporator coil kickplate created an unsightly appearence as result of a broken snap-in plastic connector. The repair should have been fairly simple, merely requiring the removal of the old plastic kickplate by depressing the plastic connectors upon each end to release the original kickplate, followed by snapping the new kickplate into position at most, a five minute repair. However, although the replacement kickplate I received from PartSelect for $58.67 (plus shipping), does contain all four plastic snap-in connectors as required, the replacement kickplate had not been molded to rest flat upon the front refrigerator trim, properly concealing the evaporator coils (as the original kickplate mounted prior to sustaining a broken snap-in connector). However, after replacing this plastic kickplate, my refrigerator continues to suffer from a pitiful, drooping kickplate upon one end. Although PartSelect has always come through for me upon previous repair part orders, in this case the better choice would have been to dismissed my desire for retaining the factory appearence of this expensive appliance, and simply apply adhesive to the original kickplate instead.
9 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Kim from Saint David, ME
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Wrench set
Parts Used:
WB25X10019, WB44X10046
Convection oven not work in microwave.
I did some research and found the part through this website. Very easy to change the heater sheath, just took long to take everything apart. Looked at some diagrams to see exactly where the part was.
9 of 25 people found this instruction helpful.
Was this instruction helpful to you?
John from ORLANDO, FL
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
WB25X10019
the halogen light above the stovetop burned out
the online instructions were ideal - just unscrewed the right-hand screw (the only screw) and replaced the bulb by inserting gently but firmly)...getting the old bulb out was a pain, b/c it shattered in my grasp (with little bits of glass all over the stove!), but that has nothing to do with the purchase and installation from this site - all a very good experience
8 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Bryan from South Beach, OR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
WB25X10019
Light for cooktop burned out
Opened cover, pulled out old bulb, inserted new one, put cover back on. I was out of town when bulbs arived, my wife put it in. She said it was easy.
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
30 Reviews
4.7
out of 5
Filter By Rating:
  • 5 Stars
    24
  • 4 Stars
    4
  • 3 Stars
    1
  • 2 Stars
    1
  • 1 Stars
    0
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Model Cross Reference

This part works with the following models:

PartSelect Number: PS2351821
Manufacturer Part Number: WB25X10019
Brand
Model Number
Description
Kenmore
36363672200
Microwave
Kenmore
36363672201
Microwave
Kenmore
36363673200
Microwave
Kenmore
36363674200
Microwave
Kenmore
36363674201
Microwave
Kenmore
36363679200
Microwave
Kenmore
36363679201
Microwave
Kenmore
36363692301
Microwave
Kenmore
36363692302
Microwave
Kenmore
36363693301
Microwave
Kenmore
36363693302
Microwave
Kenmore
36363694301
Microwave
Kenmore
36363694302
Microwave
Kenmore
36363699301
Microwave
Kenmore
36363699302
Microwave
Hotpoint
CSA1201RSS01
Microwave
Hotpoint
CSA1201RSS02
Microwave
Hotpoint
CSA1201RSS03
Microwave
General Electric
CSA1201RSS04
Microwave - MICROWAVE
General Electric
CSA1201RSS05
Microwave - MICROWAVE
General Electric
CVM1790SS1SS
Microwave
General Electric
CVM1790SS2SS
Microwave
General Electric
CVM1790SS3SS
Microwave - MICROWAVE
General Electric
CVM1790SS4SS
Microwave - MICROWAVE
General Electric
CVM1790SSSSC01
Microwave
General Electric
CVM1790XS1SL
Microwave - MICROWAVE
General Electric
CVM1790XS2SL
Microwave - MICROWAVE
General Electric
HDM1853W
Microwave - GE Microwave Model HDM1853W Parts
General Electric
JVM1490BH01
Microwave - Counter Top
General Electric
JVM1490BH02
Microwave - Counter Top