This spark module or range spark module, is used in ranges and ovens. The spark module monitors and controls the spark to ignite the surface burner in a range. It does this by sending a certain amount of current to the igniter to produce that spark. If you are not getting any spark to the igniters then it is best you replace this part with a new spark module. To repair, first remove the access panel at the back of your range with a 1/4 inch nut driver to take the screws out. Next, disconnect the power harness that connects the range to the power cord to access the spark module. Take wires off using needle nose pliers and pull the spark module off the range. Match and hook up the wires to the new part. Refer to the manual provided by the manufacturer for further installation instructions and guidance.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Will Not Start | Gas igniter glows | but will not light
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
William B - September 13, 2018
Verified Purchase
Great replacement
Great replacement that fit like OEM. Was a bit tricky to install.
★★★★★
★★★★★
William B - May 20, 2018
Verified Purchase
Spark Module replacement-easy to order and install
Installed the part with ease. After many years of no spark, the range now works perfectly. It arrived as promised and snapped into place after d=connecting the wires.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.6 / 5.0, 3 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Top burners were not lighting without a match
Was easy...I pulled oven out from the wall so I could get to the back.i used a nut driver to remove small silver cover.matched up wires to the never module and re installed.pluged oven back in and burners lit perfectly
Earl from ALLIANCE, OH
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
3 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Two of theTop gas burners would not spark
Took 6 screws out holding the top on from the sides. Lifted the top front, popped out the spark module, Took 6wires off & reversed the processed to install the new one. I was really amazed when I ordered it Wednesday and it arrived on Friday. Believe me I bookmarked this site.
Robert R from Lewistown, PA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner ingnighter would not lite burner
Replaced the ingintion module, still did not work, replaced the burner complete with new ingiter , it now works but another one quit . the front right one has 5 ohms resistance ,replaced with new one with 0 ohms, the back left has 2 ohms resistance and now it does not work , will need to replace that burner allso. too bad you can't buy ju
... Read morest the spark module for the burner.
Ask our experts a question about this part and we'll get back to you as soon as possible!
10 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Anser
January 13, 2020
I have a Frigidaire gas stove which has all the igniters sparking all the time when the stove is plugged in. All the knobs are in the off position. What can the issue be? Could it be the wiring harness or the spark module?
For model number FGF366CSC
Hello Anser,
Thank you for your question. Our sources suggest its likely a defect in the spark module under part PS2350722 for your model that's causing the issues with each igniter. We hope this helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Alan
April 14, 2018
The R. Front burner will not ignite-no spark. Will light with a match. There is spark on all of the other igniters.Would this be the module or would it be the igniter at this burner?
For model number 790.71542601
Hi Alan, Thank you for the question.This sounds like a defective spark electrode. The electrode is only sold as part of the Surface Burner Orifice Holder, PartSelect Number: PS439987/ Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Freddy
February 1, 2023
Hi.
The left Front and Right back burner will not spark of my Kenmore elite stove.I can hear and smell the gas. Will light with a match. There is spark on the other 2 burners.
Would this be the module igniter for this burner and where in the stove is this part?
Thank you I’m advance.
For model number 79046813992
Hello Freddy, thank you for your question! The issue seems to be with the spark module and you may need to replace it, the part number is PS2350722. The Spark module controls the spark for lighting the surface burners and is located at the back under the access panel. If you need help placing an order, customer service is open 7 days a week. Thanks again for your great question.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Katie
November 21, 2019
Hi, i have a Kenmore gas oven. The top burners work okay. However, the oven will not light. With thanksgiving next week, i need my oven! Can somebody please tell me the correct name of the part &/or its number? Please? As soon as you're able, would be so appreciated. Thank you for your time and consideration! Katie d.
For model number 79071202703
Hello Katie,
Thank you for your question. You likely need to replace the oven temperature sensor under part PS12724046 for your model to fix the oven. Hope this helps!
No electronic igniters work or click for burners or oven you can light the burners with a match when the knob is turned on
For model number 30-3352-23-04
Hello Don, Thank you for the question. This is normally an indication the Spark Module is defective and needs to be replaced. We hope this helps!
Was this helpful?
Thank you for voting!
Robert
December 5, 2022
All the stove top burners are difficult to ignite. Must push burner knob(s) in and turn several times before they spark. And then, at times, they continue to spark after the burner(s) ignite. Also, infrequently, some of them will not ignite at all. What could be causing this problem???
For model number FGF337GCF
Hello Robert, thank you for asking. According to our research, we would recommend checking the following parts to fix your issue: spark module, part number PS2350722, regulator, part number PS16218309, and safety valve, part number PS446204. If you need help placing an order for it, please feel free to give us a call. We look forward to hearing from you!
Oven doesn't ignite all the time
Can turn it on and will smell gas but doesn't always ignite
Burners all work/have spark to ignite
Could it be the spark module?
For model number GLGF376DCC
Hi John, thank you for your question. If the oven will not ignite it is either the Spark Module part number PS2350722 or the Oven igniter part number PS444179. You can test the ignitor with a multi meter, If it shows resistance, it has continuity. No resistance? No continuity. Typically these will be somewhere between 80 and 175 ohms of resistance for a working igniter. We hope this helps.
One rear igniter is not sparking, but there is continuity from the coil to the igniter tip, so i am thinking we need to replace the coil? Can one coil output be dead while the remaining three still produce a spark?
For model number 790.75762001
Hi Blaine,
Thank you for your question. If one of the burners is not sparking, the issue may be the switch for the that burner that is attached to the wire harness. The park igniter would be another part that you will need to check. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
Jose Nava
March 4, 2019
Spark keeps sparking on all 4 burners every few minutes?
For model number FGF337ASD
Hello Jose, there may be a leaking or debris inside the range, or you may need to replace your igniter orifices for each one if there is obvious damage, or decay. Hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
