Average Repair Rating: 3.3 / 5.0, 1 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
not cycling
put new part did reset on main controles
donna from gardnerville, NV
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ron
September 24, 2019
E35 code.
For model number E1FLS60J1W0
Hi Ron,
Thank you for your question. If you are seeing the E35 error code on your washer, it means that the water pressure switch is letting you know that the water in your washer has overfilled. If the water in your washer is above 4 1/2 inches, the issue a water problem. If the water level is low or at a normal level, the error is with the pressure sensor and it will need to be replaced. You should also check the water level as it is entering the washer. Look through the door as the water is filling, if the water continues to pour into the washer, unplug it. This should stop the flow of water from going into the washer. If the water is still pouring in after you have unplugged it, then the issue is with the water inlet valve. If the water does stop, the issue is with the electronic control board and it will need to be replaced. You should also check the wiring between the electronic control board and the water inlet valve to make sure it is not damaged or broken. If it is damaged, you will need to replace the wiring harness. I hope this helps. Thank you and have a great day!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Ralph
February 26, 2019
Washer doesnt fill on wash cycle
I reset the machine a code 32 came up
For model number Kennmore 41741122410
Hello Ralph, Thank you for contacting us. Based on the symptom I actually suggest checking part PS3655041 Drain Pump with a multimeter, and also for any blockages or debris. Most often this F32 error code is an indication the drain pump has failed. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Matt
October 16, 2019
I do not get any errors and water flows when using the "rinse and spin" and "delicate" cycles but get an "e11" code and no water flows when using any other cycles. Is this the solution to the problem or is it the main control board since this happens on certain cycles?
For model number FFFW5000QW0
hello Matt, Thank you for the question. The "E11" error occurs when the washer takes too long to fill with water. After a set amount of time, the washer stops filling and will automatically drain if not enough water has been added. Turn the faucets on all the way to give the most water pressure into the washer. Check the hoses to see if there is any leaks behind the washer or with the connection and there is no blockage.If all is good, you may have a defective Water Inlet Valve PartSelect Number PS3490374. Hope this helps!
When in spin mode washer spins slowly with medium or large load. With small load (few items) spins ok. I replaced drain pump and inspected drive belt which looks good and drum spins freely. No error code showing on display.
For model number 41741102000
Hi Les, Thank you for reaching out. If the Belt is good, you may have a faulty or weak Motor. Good luck with the repair!
