Broil Element - Push On Terminals W10201551

turn off all electric to the wall oven. removed the old broiler. replaced the new broiler and turned on the electric. checked the brolier one to see if it worked....it did thanks for the customer service for her help in finding the replacement part.

Turned off circuit breaker. Unscrewed old element holders from inside broiler - 4 screws. Pulled old element out to expose slip on wire connection at end. R&R with the new one. Screwed assembly back in. Turned on CB and tested. Good to go.

1. Turned off the electrical power. 2. Removed 4 philips head screws two from hanger bracket two from oven burner. 3. When hanger bracket screws are removed the bracket can be slid forward off the burner element. 4. When the burner element screws are removed the burner can be pulled forward where the wires can be removed (they are push on connectors)I did not need pliers but you may need them to assist you. Make sure the wires don't fall down into the oven holes. Reattach wires to new burner. Reattach burner to oven rear wall. Reattach hanger bracket. Turn on the electrical power. Broil your self a steak for a job well done.

Easy repair. Disconnected power to oven. Removed two screws holding rear connectors and two screws holding element support. Replaced with new element. Turn power on and it worked.

replacing this was very easy and simple. I removed the 2 screws holding the support bracket then the 2 screws in back of the elemant ,pull clips off the element then installed it back like it was .....very simple...

I took the old one out and put the new one in. Even a woman could do it.

I unplugged the oven then, one element at a time, I removed the screws and pulled the connecter out of the sleeve. This was the hardest part as it is a tight fit. Then, reverse the order to replace the element. The upper elements were more work because of the brackets used to hold them in place. But this only took alittle more time to remove and replace each one. When I plugged the oven back in and turned it on everything worked great! Back to baking!

Turned power off at the breaker for the range--double check to be on the safe side ---pair of light rubber type gloves-- stool to sit my old butt down on and a Phillips screw driver--removed the top burner first this is accomplished by removing the screws on each end of the burner unit--now each end of the burner unit has an coupling which will pull apart--wiggle the connection side to side and pull--when you have the couplings apart you have to remove the top brace that this burner unit slides into you remove the old unit and remove the bottom unit the same way except it doesn't have a brace---it helps to have long arms, which I don't , it was a bit of a stretch--be careful---plus I have a very thankful wife!!!!

Our Maytag electric range has a small oven on top that doubles as a toaster, and food warmer. The lower one is a big oven suitable for Thanksgiving Turkey Etc. It is also a broiler as is the top oven. The top one had the bottom element burn out about 5 months back as well. Now the bottom element on the lower oven had burned out as well. The oven has some age on it, but when I looked to replace it I saw it would be approx $1800.00 - $2000.00 for a new one. I knew the elements were replacable and thought if I should call out the lonely guy, the Maytag repairman. Nope, I pulled the stove out disconnected the 220 power supply. I got the Model number off the back stamped info plate. I looked up Maytags parts on Google and the first one was PartSelect.com. They have easy fill-in spaces for Model and Make and a schematic of the oven and all it's pieces are visually displayed. I found the part I needed and ordered. It arrived in two days, very reasonable, very fast shipping. Pulling out the old elements required only a battery operated screw driver, a flash light, and a magnetic dish to keep track of the screws.The removal of the rear panel takes about 10 sheet metal screws. I marked the leads I disconnected by color with a felt tip pen on the back. I disconnected and removed the aforementioned clips, cleaned inside the oven and placed the new element in, reconnected everything on the back as it had been according to my color assignments, replaced the back with battery operated screwdriver from the magnetic dish, reconnected the 220V power supply. Done, in about 30 minutes; I saved a bunch over a new Stove and at least a couple hundred over a service call. Easy and satisfying.

Removed four screws and the brace holding the existing element. Replaced with new broil element and secured with the four screws and brace.