Quick Question!

Have you ever purchased from PartSelect.com before?

2340881-1-S-Whirlpool-6-915776-Control Panel - Black
2340881-1-S-Whirlpool-6-915776-Control Panel - Black 2340881-2-S-Whirlpool-6-915776-Control Panel - Black https://www.partselect.com/Schematics/Maytag/53051.gif

Control Panel - Black

Your Price

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS2340881
Manufacturer Part Number 6-915776
Manufactured by Whirlpool

This part does not contain the electronic board that controls the functions of your dishwasher - it is sold separately.

This part works with the following brands: Maytag.

This part works with the following products: Dishwasher.

This part fixes the following symptoms:

  • Door latch failure.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.4 / 5.0, 3 reviews What's this?
1-3 of 3

6 of 8 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Socket set
Customer: Lionel from Columbia, MD

Control panel & latch handle failure

Don't over think the process, removed module and replaced damaged parts.
Worked the first time re-assembled.
Replaced control panel and latch handle with minimum effort and time.
Needed “star bit” to remove primary screws associated with main door panel. Delayed experience when double sided tape was required to adhere protective plastic shield for electronic touch panel component.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: More than 2 hours
Tools: Nutdriver, Screw drivers
Customer: Monte from Concord Twp., OH

Panel attachment points broken

Removed screws on the inside of the dishwasher - removed interstainless cover - disconnected wiring harnesses - accidently pulled terminal loose from control board - cut wires to terminals-took control board out - resodered terminal - used wire nuts to attached cut wires - attached wire harnesses - installed intercover - replaced screws - tested dishwasher - all okay.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 5 people found this instruction helpful

Parts Used:
  • Control Panel - Black
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Screw drivers, Socket set
Customer: Jeff from South Saint Paul, MN

Plastic handle mounts broken.

Finished the project in 50 minutes, including eating lunch in between. Steps involved: 1. Open the dishwasher door and remove the 10 screws holding the inside door to the front of the unit (need to use a star head with your screw driver for the special screws). 2. Close the inside part of the door and insert a screw, pencil or anything that will fit in the latch to keep the door closed (this will keep the door from continually falling onto you while you work). 3. Gently pull the front latch off it's mounts (the latch is snapped into two plastic anchors and has to be "popped" out. My plastic anchors where broken so the latch came out very easy). Also, you may have to disconnect the two wire harnesses from the sides of the latch unit. Look closely and you will see two plastic stems that hold the wired parts in, you just have to push the two stems back just a bit and gently pull the wiring units away from the latch. Make sure you remember which side you removed them from. 4. There is a plastic sheath protecting the main control module from getting moisture on it. It is glued on so you have to remove it. This is the only thing I wasn't prepared for as I had no glue to replace it. I found some double sided sticky tape that I used which seemed to work well. 5. Find the screws holding the main control module and the rest of the screws in for the front panel cover that you will be replacing and remove them (you will need a small socket wrench for this) 5. The main wiring module is also held into place with approximately four smaller plastic moulded clips on the top and 3 or 4 longer plastic moulded clips on the bottom. You will be replacing this plastic part so you don't have to worry if they break while removing the control module (it's still a good idea to never force anything to the point of breaking). 6. Once you have the main control module and the front plastic panel removed, replace it with the new part and screw it back into place saving the control module for last. 7. Snap the control panel module back into place and replace the screws you took out when removing (this was the most difficult step in the entire project as the control module is hard to snap back into place. I finally tilted the upper part of the module into place under the top-smaller clips and then snapped the bottom into place. Make sure the entire control module snaps in and be very careful not to break any of the plastic clips). 8. Replace the plastic sheath that covers the control module (I used double sided sticky tape) You will also notice the plastic sheath has two cuts in it for the latch area. You can just put those over the latch and line up the sheath where you have to glue it back. 9. Snap the center latch into place and then reconnect the wiring harnesses. 10. Close the inside door panel and put the 10 screws back in (make sure to go around the outer edge of the door with a flat screw driver and make sure it "pops" into place behind the plastic outer cover)... 11. Check your dishwasher to make sure it works. Some of the push buttons seemed stiff but this was due to having a new front panel, just need to push a little harder to run it). Good luck!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-3 of 3

Model Cross Reference

This part works with the following models:

PartSelect Number: PS2340881
Manufacturer Part Number: 6-915776
Brand Model Number Description