Average Repair Rating: 2.3 / 5.0, 1 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
A local technician diagnosed my problem as a faulty control board.
I followed the PartSelect video instructions for board removal and reinstallation of the new board. Even though I took a picture of the old board connections, I didn't need it. The video instructions were very clear, detailed and accurate.
Bob from COTATI, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Sherry
October 8, 2017
I am receiving an error code of E90. I am assuming it is the Green circuit board. If not, what could it be and what part would i need?
For model number LTF2940ES3
Hi Sherry,
Thank you for your question. The E90 error code just means that there has been a miscommunication between the two boards in your appliance. Unfortunately it does not say what the problem might be. It could be that this code is showing up because there was a power glitch. Unplugging your appliance for 5 minutes and plugging it back in may fix the issue. If your error code persists, it could be either one of your boards that is the issue. You may need to get a technician in to service your appliance. Good luck with your repair.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Matthew
February 27, 2018
I'd like to make sure this is the part I need, maybe you can assist. My machine is "skipping" the spin cycle, it gets anywhere from 10 minutes to 7 minutes left, will begin the slower rotations, then in a split second count to 0 and end cycle. Meanwhile the clothes are still sopping wet. On older mechanical models, I'd replace the timer.
For model number LTF2940EE0
Hi Matthew, Thank you for the question. This woudl still be a timer issue but the time is part of the control board so the board will need to be replaced. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
William
June 12, 2024
The control panel lights randomly turn on and flash when the machine is idle. My wife says occasionally it will flash ERR on the display. It operates normally otherwise. I suspect the control board. What do you think?
It's been a fantastic washing machine and I'd like to keep it running. Thanks for your help.
For model number GLTF2940FS1
Hello William, thank you for reaching out. According to our research, the ERR is not a fault error. Pressing any button during operation of the cycle will produce flashing indicator lights or beeping with Err displayed. We hope this information helps!
Was this helpful?
Thank you for voting!
TONY
September 20, 2017
If the door want lock could the control board be bad if so what should we do
For model number GLTF2940ESO
Hi Tony,
Thank you for your inquiry. If your door is not locking there are some parts that you will need to check to see which one is causing the issue. You will need to check the door strike, the door lock and switch assembly and the door hinge. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Washer","title":"Washer","url":"/Washer-Parts.htm"},{"position":2,"name":"Circuit Board or Touch Pad","title":"Circuit Board or Touch Pad","url":"/Washer-Circuit-Boards-and-Touch-Pads.htm"},{"position":3,"name":"137006000","title":"137006000","url":""}]
You added 1 item to your cart
✖
% OFF
$
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
