NOTE: This part has been updated by the manufacture and the shaft seal is now incorporated into the sump housing. The seal for diverter motor shaft only available with the pump sump housing.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Viv
February 17, 2018
The lower washer arm does not rotate/spin during the wash/rinse cycles.
For model number KUDE60FXWH0
Hello Viv, Thank you for your inquiry. Check for any clogs or debris by seeing if the spray arm will turn freely manually. If it doesn't, remove the arm, the screen filter, cover, screw and retaining-cleaning out any debris along the way. Next, check the sump for any clogs or debris. You can test the diverter motor with a multimeter to see if it has continuity, and if not, then replace it. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Ryan
October 18, 2019
Cycle stops with oversudsing error even when only running water. All research points to diverter motor. During cycle, diverter motor tries to run and clicks. Diverter plate doesn't seem to change position and is in between two openings. Thoughts?
For model number 665.13963K010
Hello Ryan, thank you for your question. Yes, based on your description it sounds like the diverter motor should be replaced. I hope this helps.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Randy
December 17, 2018
Diverter motor i need the rubber seal above that diverter motor can’t find it on the schematic where can i buy this ??
For model number 66513963k014
Hi Randy,
Thank you for your question. The seal for diverter motor shaft only available with the pump sump housing. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Robert
May 28, 2019
I have replaced the thermostat and tested the heat element (15 ohms). The dishwasher does not heat the water in the wash cycle but seems to heat in the final rinse cycle and dry cycle
For model number KUDE48FXSS4
Hello Robert, Thank you for the question. I suggest running the tap at the sink until the water runs hot before starting the dishwasher cycle. The water that enters your dishwasher must be at the minimum 120 degrees Fahrenheit. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Daniel
March 8, 2023
hello I am looking for the seal of the and the Diverter Motor of the model of my dishwasher 66513193k902 because it leaks from the diverter motor do you have the two pieces
Thank you for your help
For model number 66513193k902
Hi Daniel, thank you for your contacting us. The compatible diverter motor for your model is part number PS2328555. The manufacturer has incorporated the seal into the sump housing; order the sump, part number PS2329328, if you need the seal. If you need help placing an order, customer service is open 7 days a week!
Average Repair Rating: 2.8 / 5.0, 1 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Water leaking underneath dishwasher
The leak was dripping from the diverter motor. After removing dishwasher the diverter motor was found to be corroded. The shaft grommet looked good. A new diverter motor was installed and dishwasher connected. After running it awhile the leak reappeared. It seemed the only possible thing left was the shaft grommet. Of course the grommet comes as part of the belly assembly. After searching for a better and cheaper solution I ordered a Whirlpool WPW10195677 grommet and it solved the leak.
John from Springfield, OH
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Wrench (Adjustable)
43 of 51 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Customer Reviews
Average Rating:
★★★★★
★★★★★
1 Review
5.0
Filter By Rating:
5 Stars
1
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
John L - May 1, 2019
Verified Purchase
Diverter motor on Kenmore (whirlpool)
New diverter motor was an exact replacement. Had the same part number and origin (China). Should give us another 5 years of service.
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
PartSelect Number: PS2328555
Manufacturer Part Number: W10155344
The Fix App makes it easy to manage all your stuff in one place. Just snap a photo and we'll find and store your user manuals, receipts, and product information in one easy-to-find place!
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff
