This is a replacement haliant element for your cooktop or range. It is used with flat top ranges, and is found under the glass top of the range. This element is approximately 12 inches in diameter and is sold individually. The haliant surface element supplies the heat needed to the top of the cooktop. If your burner is not lighting up when it is turned on, you may have an issue with the haliant surface element. Be sure to disconnect power to the range before you begin this repair. To replace the element, remove the screws holding the cooktop in place, then remove it. Then, remove the screws holding the burner in place, disconnect the wires and replace the burner. Replace the cooktop and screw it back in to complete the repair.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Earl G - May 1, 2024
Verified Purchase
Awesome part
This was the perfect part and simple to install.
★★★★★
★★★★★
Edward B - June 3, 2021
Verified Purchase
No hassles
Easy order, easy install.
★★★★★
★★★★★
Jeffrey D - July 26, 2020
Verified Purchase
Easy Fix
Everything on the Haliant Element matched up perfectly with the factory original and made the repair job 5 minutes long.
★★★★★
★★★★★
David A - July 24, 2020
Verified Purchase
Part Works Great!
My Haliant Element that I ordered arrived quickly and securely packaged. After installation, the part worked good as new!
★★★★★
★★★★★
JAMES M - November 22, 2018
Verified Purchase
stove element
fast shipping and lower cost then from ge direct
even came
with directions
★★★★★
★★★★★
Edwin R - January 1, 2021
Verified Purchase
Good
Good
★★★★★
★★★★★
David W - July 8, 2020
Verified Purchase
Hot again!!!
Perfect part and easy to install. It mounted easily and now we are cooking again!
★★★★★
★★★★★
Daniel K - July 23, 2023
Verified Purchase
Easy repair
Back up and running
★★★★★
★★★★★
Keith C - July 20, 2019
Verified Purchase
Simple repair
Part was packaged properly and received in good condition. Order received in two days. Appliance back in working condition same day received. Best part was there part illustration on the website
★★★★★
★★★★★
Wayne T - June 11, 2019
Verified Purchase
Simple fix
Part came fast and was easy to install. Cooktop working like new. Am very happy.
< Prev
1
2
3
Next >
Customer Repair Stories
Average Repair Rating: 3.4 / 5.0, 9 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Interior burner of right front dual burner was out
Initially replaced the switch on the range--a simple job--pull the wires one by one and place them on the new switch. This did not resolve the problem, which meant that it was the burner, not the switch. I left the new switch in place and ordered a new burner. This, too, was simple, but involved creating a detailed drawing of the switch c
... Read moreonnectors rather than photos, which, because of the crossing of similarly colored wires, might have been confusing. The only hitch was that the burner is attached to the top by indented clips that fit into pegs at numbered locations on the burner. The clips were very difficult to open and situate, but once done (and this step was the only one where a second person was required) the top was closed and screwed back in place (two screws) and it worked perfectly.
Read less
MARK from PHOENIXVILLE, PA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The stove top had a 12” double burner that only outside burner was working
Ordered the part, turned off the circuit breaker, test to see that power is off, take a 5/16” nut driver, and remove the 2 screws under the front of the stove top, then lift the top up and hold it up with an old 2x4 about 24” long. All the connections are plug and play, so I took some needle nose pliers, to pull all 5 wires off of the bur
... Read morener. Then all that’s left to do is remove 3 spring clips. That was easily done by inserting a flat screwdriver into the back of each clip and pry them out. It ended up being a very easy fix. There is Utube videos to show you how to do it.
Read less
Mark from SEYMOUR, IN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
5 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner inside element not working
Being a front burner, I used a 24 in piece of wood to hold up range top. After removing to screws holding top. Made note of numbers on old burner and wire locations. Took off wires and three spring clips. Then replaced with new in numbered locations , wires next
Daniel from BURLINGTON, MA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
5 of 6 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Large right burner would only light in the outside and would not stay on
Ordered the part. Received the box damaged and did not realize the part was damaged until our son came all the way from Columbus Ohio to install it. We ordered another part which came in a timely manner. Even though I reported the problem and told them that we are not very computer literate they still would not accept that the part was da
... Read moremaged until we sent a picture. Our son came back from Columbus to install the new part which took about an hour. He took pictures which I was then able to send. They then asked for a serial number. I had already sent all the numbers from the part but that is when they said they wanted the serial number from the stove. We are elderly and getting that required me getting on my hands and knees to get it near the floor. Luckily I was able to get up. After multiple emails I now have to send the part back. Good luck to anyone working with this company. I will be waiting for them to reimburse me for the defective part.
Read less
JoAnne from LAMBERTVILLE, MI
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Wrench set
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
12" Haliant Element would only work on the outer ring.
Watched repair videos on YouTube to prepare. The repair was very easy.
William from RICHMOND, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
5 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Inside burner did not heat
Disconnect old burner and reconnect new one
Roberto L from LAUREL, MD
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
4 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Element went out in glass top stove.
Unscrewed the stove top and replaced the element.
Aleshia from O BRIEN, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
4 of 6 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Baking element and dual stovetop burner were fried
Baking element:First, turn off your breaker so you don't get injured. Using a small nut driver, remove the two screws that hold the element into the back of the oven. Once the screws are out, the element slides out, toward the oven opening. Be careful not to pull too hard, or the wires could disconnect from the back and be difficult to re
... Read moretrieve. Once the wires are exposed, disconnect them from the terminals. Attach them back to the new element, and put it back in. EASY For the stovetop, this is a glass top, so the burners are underneath. There are two small screws on the underside of the stove top, where the oven door closes. Remove those screws and then lift the front of the entire stove top. It will hinge at the back. There are two screws and little metal brackets that hold the burner in place. Remove those screws and brackets, disconnect the wires, and be sure to remember which wire goes where. Reattach the wires and screw the brackets back into the burner. Refasten the stovetop and you are good to go.
easily lifted the top of the stove after removing two small screws in front of the stove.removed screws holding burner in place , disconnected some wires and replaced burner. be sure to turn off the power before beginning this project
matthew from waterford, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
19 of 24 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
17 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Huarong Li
November 11, 2017
Two large burners (#57, 58) got out order. When turned on but the internal small burn at the center does not heat up. Very likely, the wire is broken. Can i just order the burners? What is the price for each? Thanks, huarong li
For model number JP80DM2BB
Hi Huarong,
Thank you for your inquiry. If the center burner is not heating up, you will need to check the switch that turns it on or the element, the wiring between the switch element and element itself with a multimeter. I hope this helps. Thank you and have a great day!
9 people found this helpful.
Was this helpful?
Thank you for voting!
Ulises
January 29, 2018
On my stove part 57 and 58 burners when turned on only outer circle heats up not the center if part is bought and replaced will it work again?
For model number JB850SF4SS
Hi Ulises, Thank you for the question. The issue would be with the Element or the switch that controls the element. I suggest testing both parts with a Multi Meter to determine the defective part. Hope this helps!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Michael
December 18, 2019
A follow up to my last question: How do you test the heating element to determine if it has failed? The element is an expensinve part and want to be sure i need to replace it.
For model number GE JB655SKSS
Hello Michael and thanks for writing.
Take the elements out of the stove, it's time to check them. Set your multimeter to resistance times one and touch the probes to the wire terminals. This should give you an even reading. Now place one probe on the wire terminal and the other on the element. The needle should not move. If there is no continuity or if the needle moves with these tests, you will need to replace your heating element as this means there is a malfunction. We hope this helps. Please contact us anytime.
5 people found this helpful.
Was this helpful?
Thank you for voting!
Joan
December 7, 2022
I am not sure of the size it is the big burner that went out on my stove. I’m not sure of the size if you could help me with it I appreciate it. Thank you.
For model number PB970BOM2BB
Hello Joan, thank you for reaching out. We have researched your model and found that this element, part number PS2321564, is approximately 12 inches in diameter. Please contact customer service if you need help placing an order, anyone will be happy to assist you. We hope that helps.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Robert
January 18, 2023
The twelve inch dual heating elemnet only the outside ( or hi) is working. Should I replace both the switch and the element? And what part numbers do I need? Thank you!
For model number Jb655sk2ss
Hello Robert, thank you for reaching out. The issue seems to be with the Surface Element and you may need to replace it, the part number is PS2321564. If that does not help, we would recommend replacing the Element Control Switch, part number PS11729102. If you need help placing an order for it, please feel free to give us a call. We look forward to hearing from you!
The element heat indicator light is always on for the large 12" element. It heats up for a minute then shuts off. It can't sustain heat when trying to place a pot on it.
For model number CBC980STSS
Hi Bryan, thank you for reaching out. Based on our research, you may need to replace the element, part number PS2321564, to fix the issue. We hope that helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Tom
October 29, 2019
Dual ring surface elements can not reduce heat on either ring with control knob
For model number JB655DK3WW
Hello Tom, Thank you for the question, In most cases this means the switch that controls the element will need to be replaced. PartSelect Number PS11729102. Hope this helps!
Do the range top heating elements have a thermostat control. It seems one of ours may be overheating. Can this crack the glass top?
For model number GE JB655SKSS
Hello Michael and thanks for writing.
No, there is not a thermostat there. It certainly sounds more like a faulty element check for signs of damage and replace it if needed. Yes, it could damage the glass top. We hope this helps. Please contact us anytime.
We do carry related parts for units just like yours. For example, part number PS8754842 Good luck with your repair.
My burner is stuck on the "high" setting and won't lower no matter the knob position. Is this a burner problem or something with the wiring, or something else?
For model number JB860DJ1WW
Hello Crystal, Thank you for the question. This is an indication the Switch that controls the Element is defective and will need to be replaced. We hope this helps!
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Range","title":"Range","url":"/Range-Parts.htm"},{"position":2,"name":"Element or Burner","title":"Element or Burner","url":"/Range-Elements-and-Burners.htm"},{"position":3,"name":"WB30T10130","title":"WB30T10130","url":""}]
You added 1 item to your cart
✖
% OFF
$
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
