Quick Question!

Have you ever purchased from PartSelect.com before?

2200270-1-S-Whirlpool-Y303836-Blower Wheel with Clamp
2200270-1-S-Whirlpool-Y303836-Blower Wheel with Clamp 2200270-2-S-Whirlpool-Y303836-Blower Wheel with Clamp https://partselectcom.azureedge.net/Schematics/Maytag/36762.gif

Blower Wheel with Clamp

Your Price

$15.05
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS2200270
Manufacturer Part Number Y303836
Manufactured by Whirlpool

This comes with a metallic hub clamp to hold it firmly in place. The blower wheel with clamp is part of your dryer assembly. You will find this part attached to the drive motor shaft, which disperses air through the drum and out of the exhaust vent. This part might need to be replaced if you notice your dryer is taking too long to dry clothing, it is not tumbling, or is making any unusually loud noises. The blower wheel measures about 7.5 inches in diameter by 3-3/8 wide. The blower wheel can be accessed by removing the front panel of your appliance.

This part works with the following brands: Maytag, Jenn-Air, International.

This part works with the following products: Dryer, Washer Dryer Combo.

This part fixes the following symptoms:

  • Noisy.
  • Takes too long to dry.
  • No heat or not enough heat.
  • Will not tumble.
  • Too hot.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Blower Wheel Clamp

Part Number 11740752

This blower wheel clamp, used in a clothes dryer, is a clamp that holds the blower wheel to the motor shaft. This part helps hold the blower wheel in place to function easily and properly. If your clothes dryer has any of the following symptoms then replacing the clamp can be a solution: making loud noises, not producing enough heat or no heat at all, and/or clothes are taking too long to dry. Make sure to unplug thedryer from power source before installing this part and refer to the installation instructions provided by the manufacturer for further guidance.

$5.67
In Stock

Tumbler and Motor Belt

Part Number 11757542

The tumbler and motor belt in your dryer allows the drum to spin during the drying cycle. At 100 inches in length, this dryer drum belt is 3/8 of an inch wide and has five ridges. The belt is black in color and it is made entirely of rubber. If your dryer will not tumble, is noisy during operation, or will not start you may need to replace the belt. To complete this repair, you will need to remove the front panel as well as the drum. You will need a 5/16 nut driver and a stubby Phillips screwdriver to complete the repair. Be sure to disconnect power to the dryer before you begin this repair.

$13.81
In Stock

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Most Recent

Question:

This is a gas fired unit and the blower wheel is stripped from the motor shaft. My unit has sealed blower housing that appears to be glued together. How do I remove this from the drive motor

Ron for model number 41791122310
Answer:

Hi Ron, Thank you for your inquiry. You spin the wheel counter clock wise and that will unscrew the shaft of the motor from the housing. Good luck with your repair.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.1 / 5.0, 150 reviews What's this?
 

1 of 1 people found this instruction helpful

Parts Used:
  • Blower Wheel with Clamp
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers
Customer: David from BRANCH, MI

Noisy and clothes not drying.

After removing dryer front, remove several metal shields(ouch sharp!). Remove clamp and keeper ring and blower wheel. Then remember where all those screws came from. If I did it again I would put a spacer washer behind the blower wheel which is not in the original design. This might prevent this happening again.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Blower Wheel with Clamp
Level of Difficulty: A Bit Difficult
Time to do repair: More than 2 hours
Tools: Nutdriver, Pliers, Screw drivers
Customer: Robert from EDINA, MN

"d" bore of blower wheel spinning on motor shaft

I caused added difficulty and time by not taking pictures while I disassembled the dryer. Otherwise everything was accessible through the front. Two phillips screws to take off the lower panel. Two 1/4" hex screws on the top to loosen the front which tips out and can rest on the washer while you use the hex drive to access the blower. 4 hex screws inside the dryer for the plastic filter housing. Snap ring to remove the ring and pliers to remover the clamp . Pictures would have made it a job of well less than an hour. Note: Easy access to the snap ring so would allow remove and replace w/o the special pliers if you are handy with a flat blade screwdriver.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Blower Wheel with Clamp
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Screw drivers
Customer: Lloyd from VALLEY VLG, CA

Loud banging noise

There was a rhythmic loud banging noise coming from our dryer (sounded like there was a sneaker going around in the drum). After reading several diagnostic recommendations, assumed it was either the drum belt or one of the guide rollers, but these were found to be OK after opening the front panel. The noise was coming from the blower fan- the center D-shaped hub that connects to the motor shaft had snapped, causing the fan to wobble when running, not what was expected. Had to then place another order for the blower fan part, which was replaced along with a new belt, drum guides and new rollers. Cleaned out a lot of dust and lint, especially around the motor. Re-assembled, and now works like new.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers
Customer: Donald from BRUNSWICK, OH

Dryer makeing noise

Discovered fan spinning on motor shaft. Replace fan and clamp. and put on a new belt. The Dryer is 22 years old and I plan on keeping it for life....

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Blower Wheel with Clamp
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: John from WAYNESVILLE, MO

Thumping noise during drying cycle; long drying times due to heat cycle shortened

Removed the front of the dryer with two mounting screws at the bottom of the unit. Removed the plenum cover to expose the fan. Removed the clip ring which secures the fan to the motor shaft and slid the shaft forward to remove. Reinstalled new fan, secured with new clip and installed clip ring. Re-installed plenum cover and front panel. Ran dryer through cycle to verify repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Blower Wheel with Clamp
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Gordon from KLAMATH FALLS, OR

The fan broke off at the shaft.

I did what I normally don't do.... I followed the video instructions, one of the reasons I always buy my parts here. Thanks for the videos!!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: Roger from Owatonna, MN

Blower fan was broken and spinning on the motor shaft

Removed front cover, removed housing cover, took old fan off, installed new fan, put covers back on.
Your instructional video was very helpful. He told which screws to remove to get the covers off. I was unsure about how access the fan until I watched. Well done!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Screw drivers
Customer: Cody from Nebraska City, NE

Clunking noise when first turned on

I took the access panel off the back, realized that belt was in very bad shape. Ordered a belt when I got that changed I put it back together and it still had a clunking noise. Found out that the blower wheel was rounded off where it goes over the shaft. So to change that I took the two front screws off, then the four hex screws off of the tumbler guide. There were eight or so screws over the blower wheel, took those out and the clamp on the blower wheel then used the snap ring pliers for the snap ring, then changed the wheel. Problem solved. This website is very helpful I would not have attempted to fix my dryer without this website.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Blower Wheel with Clamp
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers, Socket set
Customer: RICHARD from ROBINSON, IL

Blower wheel hub worn out

First remove 2 screws on bottom of front panel,pull panel out from bottom to remove. Then remove 4 screws,2 on each side to remove tub support. Then remove approx. 6 Screws on fan access cover to expose fan. Then remove snap ring and clamp on fan hub. Pull fan off and push new fan on and reverse procedure.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Blower Wheel with Clamp
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers, Wrench set
Customer: CARRIE from NEW BAVARIA, OH

Loud knocking in the dryer

My husband took off the front panel and noticed that the center of the wheel was melted. We went on to this website and confirmed the noise with other customers. We ordered the part - received it in 1 day and the dryer was repaired and back together within a 1/2 hr. Part was as is - istructions excellent.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 4 people found this instruction helpful

Parts Used:
  • Blower Wheel with Clamp
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers, Socket set
Customer: james from joliet, IL

Loud rumbling

From the sound it made I thought it was the rear rollers. That happened once before on another dryer.
After removing all the parts I foung out they were fine.
First unplug the dryer:
Then remove the dryer front door panel.
2 screws at the bottom of the door.
Lift cover from the bottom of the door, it is kind of on a top hinge.
On the bottom left hand corner you will see the plastic cover for the blower. It has 6 small screws that hold the cover on.
Once the cover is off you will see the blower wheel.
Use a pair of Snap Ring Pliers to remove snap ring at end of the shaft.
Use a pair of needle nose pliers to remove the clamp around the blower wheel that holds it onto the shaft.
Slip off the old part.
That was the rumbling noise.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Blower Wheel with Clamp
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Henry from Newark Valley, NY

Fan was noisy, indicateing that the fan hub was worn, letting it wobble.

I removed the two screws and removed the front panel, next I removed the fan cover that also directs the air movement into the drying tub. I then removed the external snap ring that held the fan in place on the shaft. The fan very easily slid right off of the shaft. It was reassembled in the opposite order. A very easy procedure. The entire procedure was not more than one hour.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set
Customer: Brian from Palm Harbor, FL

Drum bearing guides worn through - general rebuild

Removed two screws on bottom of front panel. Lifted bottom of front panel, it then it dropped down and was moved to the left side. Removed 4 socket screws and removed drum front cover. Replaced felt strip, removed belt and replaced. Replaced two idler pulleys in back. Removed blower housing front cover, removed blower wheel and replaced. Installed front drum glides after drilling out rivets from the old glides. Vacuumed entire inside thoroughly and reassembled.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Blower Wheel with Clamp
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: Ronald from Cadet, MO

Making loud noise

Removed (2) screws at bottom of dryer. Removed about 5 screws on blower housing. Used pliers to remove clamp and replaced the blower. Installed everything in reverse. I looked at what others did before me and it made it easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Anthony from Citrus Heights, CA

Horrible rattle - sounds like drying a load of cleats

I followed the instructions given by other DIYs. The rubber band for the belt was a great suggestion, however having no rubber band nearby, I used a zip-tie that worked out perfectly.

The only tool that I wished I had is a pair of split ring pliers. Not having a pair, used a pair of needle nose and a very small screw driver to provide the leverage to remove the washer.

After following the instructions that came with the belt on how to properly align it to the motor wheel and tension wheel, I plugged everything back in and started it up. Sounded like it was brand new.

I decided not to replace the rollers or drum guides as they looked to be in good shape.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

Model Cross Reference

This part works with the following models:

PartSelect Number: PS2200270
Manufacturer Part Number: Y303836
Brand Model Number Description
MaytagDE106Dryer - Electric
MaytagDE107Dryer - Electric
MaytagDE110Dryer - Electric
MaytagDE18CADryer - Electric
MaytagDE18CMDryer - Electric
MaytagDE18CSDryer - Electric
MaytagDE18CTDryer - Electric
MaytagDE19CADryer - Electric
MaytagDE19CDDryer - Electric
MaytagDE19CSDryer - Electric
MaytagDE19CTDryer - Electric
MaytagDE210Dryer - Electric
MaytagDE212Dryer - Residential
MaytagDE21CADryer - Electric
MaytagDE21CMDryer - Electric
MaytagDE21CSDryer - Electric
MaytagDE21CTDryer - Electric
MaytagDE22CADryer - Electric
MaytagDE22CSDryer - Electric
MaytagDE22CTDryer - Electric
MaytagDE23CDDryer - Electric
MaytagDE24CADryer - Electric
MaytagDE24CMDryer - Electric
MaytagDE24CSDryer - Electric
MaytagDE24CTDryer - Electric
MaytagDE25CSDryer - Electric
MaytagDE26CADryer - Commercial
MaytagDE26CDDryer - Commercial
MaytagDE26CSDryer - Electric
MaytagDE26CTDryer - Commercial