Maytag/Maytag_Thumb/33621.gif
See part 1 in the diagram
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 10PM EST

customerservice@partselect.com

Surface Unit Infinite Switch Kit

★★★★★
★★★★★
4 Reviews
$ 84.54   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS2076107
Manufacturer Part Number 700855K
Manufactured by Whirlpool
Product Description

Surface Unit Infinite Switch Kit Specifications

This is a push-and-turn switch. This kit includes all necessary hardware to install the part. Switch comes with a D-shaped shaft.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Element will not heat | Will Not Start
This part works with the following products:
Cooktop, Range.
This part works with the following products:
Jenn-Air, Hoover.
Part# 700855K replaces these:
AP4087111, 2640, 700855K, 7-0009, 7-0855, 70009, 700855K, 700855KVP, W10116762, W10894486, Y700009, Y700855
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

11 questions answered by our experts.
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Leo
November 13, 2018
Does this switch fix my problem which is when i turn on my rear left coil goes straight to high heat no low
Hello Leo, Thank you for the question. If the element turns on but goes right to high, the switch that controls the element will need to be replaced. If you can provide the model number of the appliance, we will be happy to verify the parts number for you. Thank you for your inquiry, good luck with this repair!

6 people found this helpful.

Was this helpful?
Thank you for voting!
Joseph
December 26, 2017
Does this switch work with the 8'' and 6'' burner. Is there a front and rear model.
For model number D120
Hi Joseph, Thank you for your question. It looks like this switch would work for all of your burners. Good luck with your repair.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Linus Paul
April 9, 2018
Does part come with wiring diagram ? We tried another switch from another supplier and did not work. Some how the wires seem to be switched in all the confusion . I thought we saved all the wiring diagram . Where can i find the proper way to wire the new switch. Thank you
For model number C221
Hi Linus, Thank you for your question. There is an instructions sheet that comes with the switch. I hope this helps. Thank you and have a great day!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Peter
December 6, 2019
The 2 larger solid elements do not heat up to their full heating capacity whereby it takes a long time to even boil water. What could be the problem and what part numbers might i need? Thank you.
For model number C301 (Jenn-air cooktop with 2 large solid elements, 2 smaller solid elements, & a center grill
Hello Peter, thank you for writing. This is likely due to a faulty Infinite Switch, this part number PS2076107 for your model. Good luck with your repair!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Dave
December 11, 2019
Is this a set of four or only a single switch?
For model number C201
Hello Dave, Thank you for the question. This kit includes all necessary hardware to install the part and the individual Switch. Hope this helps!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Drew
December 31, 2019
Does part number 700855k a push and turn infinite switch have the wire connections on the bottom of the part or are the wire connections around the outside of the part. Your pictures show the connections on the bottom but other people i know have ordered this part number from other places and it has the wire connections around the outside and is made by robert shaw and has a part number of w10894486 but is sold as part number 700855k. I really need the wire connections on the bottom so just want to make sure. Thanks drew purvis
Hello Drew and thank you for writing. The connections are as shown in our picture, so the way you need them. Part numbers w10894486 (manufacturer part number) and PS700855k (our number) are the same item. We hope this helps. Please contact us anytime if you require further assistance.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Jim
July 11, 2019
Please provide bottom view so I can see location and number of blade connections. Also, list of included parts in kit. Thanks.
For model number Jenair c221
Hello Jim, Thank you for the question. This kit includes all necessary hardware to install the part. We can not send pictures through Q&A sorry but you can google image the Manufacturer Part Number 700855K for more views to see the 5 blade connectors. Hope this helps!

Was this helpful?
Thank you for voting!
Gregg
August 2, 2019
L-rear burner on low works correctly until you turn on the l-front, then the rear goes to hi heat what might be the problem, i'm at a loss
For model number C202
Hello Gregg, thank you for inquiring. It could be that this Surface Unit Infinite Switch is faulty and is causing the issue, but you may also want to consider the Surface Burner Receptacle part number PS1570190. Good luck with your repair!

Was this helpful?
Thank you for voting!
Elizabeth
December 2, 2019
Our electric panel is outside, and one of our California deluges soaked in the breakers for our Jenn-Air cooktop. My husband dried the area and breakers, reinserted it, but our cooktop's heating elements are not receiving power. The fan works, the lights work. Is there a breaker on the underneath of our cooktop? Or do I need these "infinite" switch replacements? Would that be all of the switches on the top, or is that a control under the cooktop. We are not handy by any stretch of the imagination, so if these are dumb questions, sorry. Ours is 47 inch wide, ca 1987, electric, 4 burners, grill and frywell. I cannot find parts for the frywell either. Model number C301 and serial number 346818RR.
For model number C301
Hi Elizabeth, Thank you for your question. If the elements on top of the stove are not lighting, you will need to check the check the electric burners, the switches and the terminal wiring with a multimeter to see which part is causing the issue. To test the terminal wires, Visually inspect the terminal block for any signs of damage, cracking, or burning. Using a multimeter on the Rx1 setting, touch the probes to the terminals. If your receptacle has multiple sets of terminals, test each set individually. If there is continuity, your multimeter will produce a reading of zero. If you receive any reading other than zero, you will need a replacement receptacle. To test the switches, place your multimeter on Rx1 mode, test for continuity by touching the L1 and H1 terminals with the probes. Once you have completed that test, touch the probes to the L2 & H2 terminals. If your test results indicate that there is no continuity between one or both sets of terminals, you need a replacement infinite switch. To test for a shorted element, touch each of the terminals one at a time with one probe while holding the other probe to the outside surface of the element. If either terminal show continuity, it is defective. To test the entire element for continuity, place each of the probes on the terminals, one on each. The exact reading you should receive varies between models, refer to your owner’s manual to determine what yours should be, but if any element has a reading outside of 19 to 115 ohms, it is defective. If you do not receive the correct readings from the tests above or find damage on your element, you will need a replacement surface burner element. I hope this helps. Thank you and have a great day!

Was this helpful?
Thank you for voting!
Jon
April 16, 2019
Need to replace the surface unit infinite switch on a 1989 jennair c221 cooktop. The part you carries states it has a "d" stem. The units on this top appear to have a stem that looks ore like an "8." do you carry switches with this stem configuration?
For model number C221
Hello, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS12347302. Thank you for your inquiry, good luck with this repair!

Was this helpful?
Thank you for voting!
Related Parts:
Customer Repair Stories
 Average Repair Rating: 3.9 / 5.0, 32 reviews. What's this?
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Regular Parts Replacement/Maintenance.
We love our Jenn-Air electric range that we have owned since 1983 and couldn't get parts from where we bought it recently. We called around to Sears and other appliance dealers and they couldn't help us. We found your company searching on the internet and we are very much pleased with your parts listing and your great service. We will be back. Jody and Mike Hayden, Eden, Vt.
85 of 95 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner had no temperature control other that full on.
Locate and open appropriate breaker to kill power to the range. (very important if you intend to see tomorrow).

Pull off the control knob.

Remove 2 screws that hold in control pannel.

Lift out the control pannel to the extent that the wires will let you. (2-3 inches)

Remove the nut that holds the switch/controller in the pannel.

Remove the wires one at a time and reconnect them to the new switch. Make sure to connect them the same way on the new switch.

Re-install the switch in the pannel.

Re-install the pannel in the stove.

Close breaker and test burner contol.
  • Eric from North Andover, MA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
  • Parts Used:
    700855K
59 of 68 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fan switch burned out, Burner switch only worked on HIGH.
Well, since the circuit breaker blew when the fan switch burned out, I was hoping to get a new counter-top range out of this. But, no such luck. My son opened up the control module (2 screws under the fan grill) and found the problem. Then I decided that if I needed to replace ONE part, I'd replace ALL of the parts that didn't work and were worn out.
First I turned off the breaker all the way, then, since the module was open anyway (it pulls out about 2 inches), I only had to remove the old fan switch using the socket set, and replace it, wire-for-wire with the new one. The flange needed to be filed down a bit because it was wider than the original, but not a problem to do. I had to use the original nuts to hold in the new one. The new ones are smaller. Just used the socket set in reverse
....done!
The burner switch and knobs were a little more of a problem but only because ordering them didn't follow the rules...I needed series 3 parts, even though I had a "Run 01" range top. With the help of a very nice customer service rep, I got the correct parts the next day and replaced the burner swich the same way...used a socket set to loosen and remove the old switch and connected the new one wire-for-wire, and again needed to use the original washer and nut. (The wrong model that I initially received had a new washer and nut in the bag with the switch.) But, again, no problem.
The control knobs just pull off and push on...simple.
Now that I had a nearly new range top, I spent another 2 hours REALLY cleaning it (Dawn Power Dissolver is GREAT!). Looks almost like new! I guess I won't be getting a new range top for another 22 years now.....
  • Judith from Leominster, MA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
  • Parts Used:
    WPY700854, 700855K, 12200054
15 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
two of the surface unit infinite switch D-shaped pins were broken
following the directions in the package and on-line, this repair was easier than i could have imagined. changing out these two parts took less than 15 minutes.
  • Susan from San Diego, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
  • Parts Used:
    WPY700854, 708706, 700855K
13 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Switches on my range top quit working! Range top is over 20 years old. Local appliance parts store said they could not get parts I needed! What a great feeling I had when I found the parts I needed at PartSelect. I was able to see excellent pictures of the parts, consequently I felt safe ordering
I unplugged the range top power cord. I used a phillips screw driver and crescent wrench to remove the old range top switches. I disconnected the wires from the switches. I reconnected the wires to the new switches and installed the switches into the range top switch panel. This took about one hour. I plugged in the power cord. The range top works great and looks great with the new switches.
  • Mary from Kokomo, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench set
  • Parts Used:
    Y700132, 700855K
9 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Both the 8'' burner and the vent fan didn't work.
1st-turned off breaker, 2nd- took out the two screws that hold the control panel and lifted it up so I could remove the surface unit switch,3rd- removed wires from old switch and securing nut and removed old switch,4th- installed new switch and plugged in wires, then turned on breaker to see if burner would work and it did. 5th-turned off breaker again and removed the wires from the fan switch and used nut driver to remove retainer nuts,6th-installed new fan switch and plugged in wires, 7th- put control console back in place and the two screws that hold it in place. Turned breaker back on and everything worked.Didn't use the burner receptacle or burner.
  • Walter from N. Richland Hills, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
8 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old switch had burned out and needed to be replaced
Turned off electricity at the circuit box. Removed four screws from panel cover that housed the switch. disconected the wires from the old switch and replaced the old switch with the new one reconected the wires put the panel cover back on. voila done.
  • Jeannine from Twentynine Palms, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
  • Parts Used:
    700855K
7 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Switches were worn out (2) and shorting out. Throwing the breaker. Actually I think the ladies boyfriend/ fiance' tried to replace the knobs that were broken with universal knobs. They didn't fit so he forced them and broke the switches internally.
Shut off the breaker! Removed down draft grill. Removed two phillips head screws and lifited switch plate out. Removed switches (2) and made wiring diagram as I went. Looked up Jenn-Air on line and ordered parts. Lost wirihng diagram in the process but still had two switches wired . Replaced all four switches. Everything working great. However while I was waiting on switches to arrive, somebody at the house was fooling with the switch plate and broke the on red indicater lens so now I'm ordering that. Oh well....
  • Jerry from Midland, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench set
  • Parts Used:
    WPY700854, 700855K
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner would n.ot het hot
We unscrewed the top plate, unscrewed the top of the switch removed the ballast underneath and it worked. I was so glad to be able to still get the parts.
  • Jeffrey from Clearwater, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
  • Parts Used:
    715878, 715877, 715396K, 700855K
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The 8" burner switch would operate both the 6" and 8" burner.
First pulled the two screws holding the control with the switches. Then I unscrewed the nut holding the 6" burner switch and disconnected the wires on the switch and replaced the switch with the new one. Replaced the control unit in the range top and tested the repair.
  • Jack from Carson City, NV
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
  • Parts Used:
    700855K
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer Reviews
Average Rating:
★★★★★
★★★★★
4 Reviews
4.8
Filter By Rating:
  • 5 Stars
    3
  • 4 Stars
    1
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
    Sort by:
    Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
      Related Parts
      Model Cross Reference
      This part works with the following models:
      PartSelect Number: PS2076107
      Manufacturer Part Number: 700855K
      Brand
      Model Number
      Description
      Hoover
      2300
      Cooktop
      Jenn-Air
      2300ERS
      Cooktop - Electric
      Jenn-Air
      2320ERS
      Cooktop - Electric
      Jenn-Air
      2325ERS
      Cooktop - Electric
      Hoover
      2360
      Cooktop
      Jenn-Air
      2360EGS
      Cooktop
      Jenn-Air
      2361EGS
      Cooktop
      Hoover
      2365
      Cooktop
      Jenn-Air
      2365EGN
      Cooktop
      Hoover
      2366
      Cooktop
      Hoover
      2370
      Cooktop
      Jenn-Air
      2370EGS
      Cooktop
      Jenn-Air
      2375ERS
      Cooktop
      Jenn-Air
      2380EGS
      Cooktop - Electric
      Jenn-Air
      2385EGN
      Cooktop - Electric
      Jenn-Air
      2390ERS
      Cooktop - Electric
      Hoover
      2475
      Cooktop
      Hoover
      2480
      Cooktop
      Hoover
      2490
      Cooktop
      Hoover
      4760
      Range
      Hoover
      4770
      Range
      Hoover
      4775
      Range
      Hoover
      4790
      Range
      Hoover
      4855
      Range
      Hoover
      4860
      Range
      Hoover
      4870
      Range
      Hoover
      4875
      Range
      Hoover
      4890
      Range
      Jenn-Air
      88168
      Range - Freestanding, Electric
      Jenn-Air
      88169
      Range - Freestanding, Electric

      Get in touch, we're here to help!

      Open until 10PM EST

      Contact Customer Service