Maytag/Maytag_Thumb/LD14-40.gif
See part 004 in the diagram
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 10PM EST

customerservice@partselect.com

Blower Wheel

★★★★★
★★★★★
3 Reviews
$ 26.55   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS2035614
Manufacturer Part Number 33001790
Manufactured by Whirlpool
Product Description

Blower Wheel Specifications

This blower wheel does not come with a spring clamp, but it does have twenty fins and it is designed to fit a 3/8 of an inch motor shaft.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Noisy | Takes too long to dry
This part works with the following products:
Dryer, Washer Dryer Combo.
This part works with the following products:
Maytag, International.
Part# 33001790 replaces these:
AP4043265, 516674, 33001790
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Part Videos

Replacing your Maytag Dryer Blower Wheel

Customer Repair Stories
 Average Repair Rating: 3.1 / 5.0, 5 reviews. What's this?
    Sort by:
    Sorry, we couldn't find any existing installation instruction that matched.
    Blower wheel broke
    Replaced bower wheel, drum rollers,belt and Idler pulley while the dryer was apart. so far so good. Easy repair
    Motor bearings seemed tight so hopefully will get another ten years out of dryer.
    23 of 653 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    loud noise inside dryer
    After changing all the rollers in the dryer (which didn't fix the problem) I decided to take apart the blower. Sure enough, that was the problem. As the dryer heated up, the damaged wheel would swell and start rubbing the housing. I replaced both and fixed the problem. The repair was pretty easy, since I had taken the dryer apart several times replacing the rollers.
    • Terry from Caruthersville, MO
    • Difficulty Level:
      Easy
    • Total Repair Time:
      30 - 60 mins
    • Tools:
      Nutdriver, Pliers
    • Parts Used:
      33001790, WP33001789
    13 of 16 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Blower wheel over time became clogged w/lint & caused the dryer to vibrate
    Removed the dryer front, then detached the retainer ring holding the blower wheel in place. Set the new blower wheel, attached the new ring retainer and placed the dryer front back in place. Thank you for the low prices - I searched on-line at 3 sites and you were the best price available.
    • Carol from Onsted, MI
    • Difficulty Level:
      Easy
    • Total Repair Time:
      30 - 60 mins
    • Tools:
      Nutdriver, Screw drivers
    • Parts Used:
      WP9703438, 33001790
    8 of 10 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Blower wheel had broken fins, motor bearings loose
    This was fun! Kill the power!
    Remove door, remove from panel, remove front drum support, remove drum and belt, remove blower cover, remove blower wheel, remove electrical connector from motor, take two clips off motor mount to remove motor. Put it all back in with new parts. 200 bucks and back in business. Go for it.
    Bob
    • Robert from Lebanon, PA
    • Difficulty Level:
      A Bit Difficult
    • Total Repair Time:
      30 - 60 mins
    • Tools:
      Nutdriver, Pliers, Screw drivers
    • Parts Used:
      W10410997, 33001790
    3 of 5 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    Blower wheel was wobbly about the shaft, producing a lot of vibration and noise.
    Tools required: Stubby socket wrench, 5/16" socket, 1/2" socket, 1/4" socket, #3 Phillips screwdriver, external circlip pliers, straight slip joint pliers. A decently strong electric screwdriver is highly recommended - Milwaukee 2401-20 M12 cordless 1/4" Hex Screwdriver, for example.

    Unplug the dryer. Turn off the gas supply.

    Remove the screws holding the door hinges to the dryer.

    Remove the door and hinges from the dryer by pulling the door and hinges up, then out.

    Remove the two plastic thingies (door stops), opposite of where the hinges were, from the front panel of the dryer. Each plastic piece is held in place by two screws.

    Grasp the front panel by its top edge, pull it toward you, then lift the panel up and off the clips at the bottom.

    There are a couple metal brackets holding the top of the dryer down to the front shroud (the doorway) and frame, one on either side. Each bracket is held in place by two screws. Remove the screws, remove the brackets, then rock the top panel up and back, like the hood of a car.

    Remove the screws holding the shroud to the frame. Look carefully. There are two screws that look like they hold the shroud to the frame, but actually do not. Don't remove these screws yet.

    Remove the screws holding the plastic duct / lint screen slot to the shroud. These are very long.

    Disconnect the wires from the door switch.

    Remove the shroud.

    Remember the two screws I referenced previously, stating they shouldn't yet be removed? Now's the time to remove them. Do so, then set the panel aside, being careful not to damage any wires. Don't lose the rubber gasket sitting around the circular portion of the duct.

    There's a metal cover over the blower wheel. This cover is held in place by a bunch of screws. Remove them all, then remove the cover.

    Remove the circlip going around the blower shaft, in front of the blower wheel.

    Remove the clamp from around the blower wheel and shaft.

    Pull the blower wheel off the shaft.

    Install the new blower wheel.

    Reinstall the clamp around the blower wheel and shaft.

    Reinstall the circlip.

    Reinstall the metal blower cover.

    Make sure the rear of the drum is resting on the wheels.

    Now things become a little difficult, because you have to fight the drum a little bit. Put the panel containing the moisture sensor, front drum seal, and duct into position. (Be careful not to mess up the drum glides. Make sure the rubber seal at the bottom of the vent is in place, sealing the vent to the blower.) Screw the panel into place with two screws, but don't fully tighten yet.

    There's a felt seal that is supposed to go between the rear lip of the drum and the rear inside wall. The seal is supposed to be held folded, pinched between the lip and the wall, with the edge of the seal being outside the drum. The seal isn't supposed to jut into the inside of the drum. Use your fingers and some other tool to push the rear felt drum seal out of the inside of the drum. If you use a screwdriver, be careful that you don't cut, rip, or otherwise damage the felt seal.

    Do the same with the front felt drum seal.

    Carefully inspect the felt seals. You don't want any portion of the seal somehow working its way back into the inside of the drum. Then verify again that the rubber seal that goes between the blower housing and the vent is in place and properly sealing. Now tighten the screws.

    Connect the wires to the door switch on the shroud, then loosely screw the shroud in place. Screw the shroud to the vent. Once all the screws are in place, tighten all the screws.

    Lower the top of the dryer into position.

    Hook a bracket into one side of the lid, position the bracket over the front shroud, then screw in place.

    Repeat with the other bracket.

    Place the front panel onto the bottom clips. Seat the panel onto the clips all the way, then rock the panel forward into place.

    Install the plastic door stops.

    Insert the door hinges into their slots, push the door down to seat into place, then install the screws that hold the hinges in place.

    Plug the dryer in, turn on the gas, test.
    • Christopher from SAN DIEGO, CA
    • Difficulty Level:
      A Bit Difficult
    • Total Repair Time:
      30 - 60 mins
    • Tools:
      Pliers, Screw drivers, Socket set
    • Parts Used:
      WP9703438, WP312967, 33001790
    1 person found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
      Customer Reviews
      Average Rating:
      ★★★★★
      ★★★★★
      3 Reviews
      4.7
      Filter By Rating:
      • 5 Stars
        2
      • 4 Stars
        1
      • 3 Stars
        0
      • 2 Stars
        0
      • 1 Star
        0
        Sort by:
        Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
          Model Cross Reference
          This part works with the following models:
          PartSelect Number: PS2035614
          Manufacturer Part Number: 33001790
          Brand
          Model Number
          Description
          Maytag
          MDE14PDACL
          Dryer - Electric
          Maytag
          MDE14PDACQ
          Dryer - Electric
          Maytag
          MDE14PDACW
          Dryer - Electric
          Maytag
          MDE14PDADL
          Dryer - Electric
          Maytag
          MDE14PDADW
          Dryer - Electric
          Maytag
          MDE14PDAGW
          Dryer - Electric
          Maytag
          MDE14PNAGW
          Dryer - Gas
          Maytag
          MDE14PNAYW
          Dryer - Gas
          Maytag
          MDE14PNAZW
          Dryer - Gas
          Maytag
          MDE14PRAYW
          Dryer - Gas
          Maytag
          MDE16CSAGW
          Dryer - Electric
          Maytag
          MDE16CSAKA
          Dryer - Electric
          Maytag
          MDE16CSAKQ
          Dryer - Electric
          Maytag
          MDE16CSAYA
          Dryer - Electric
          Maytag
          MDE16CSAYQ
          Dryer - Commercial
          Maytag
          MDE16CSAYW
          Dryer - Electric
          Maytag
          MDE16CSAZA
          Dryer - Electric
          Maytag
          MDE16CSAZQ
          Dryer - Commercial
          Maytag
          MDE16CSAZW
          Dryer - Commercial
          Maytag
          MDE16MNAGW
          Dryer - Electric
          Maytag
          MDE16MNAYW
          Dryer - Electric
          Maytag
          MDE16MNAZW
          Dryer - Electric
          Maytag
          MDE16PDAGW
          Dryer - Commercial
          Maytag
          MDE16PDAUW
          Dryer - Commercial
          Maytag
          MDE16PDAYA
          Dryer - Commercial
          Maytag
          MDE16PDAYQ
          Dryer - Commercial
          Maytag
          MDE16PDAYW
          Dryer - Commercial
          Maytag
          MDE16PDCZW
          Dryer - Electric
          Maytag
          MDE16PDDGW
          Dryer - Gas
          Maytag
          MDE16PRAGW
          Dryer - Residential

          Get in touch, we're here to help!

          Open until 10PM EST

          Contact Customer Service