Glide and Spring Kit 205000 | Official Whirlpool Part | Fast Shipping | PartSelect
Glide and Spring Kit – Part Number: 205000
( Grid squares measure 1x1 inch )
Glide and Spring Kit – Part Number: 205000 Glide and Spring Kit – Part Number: 205000 Glide and Spring Kit – Part Number: 205000 https://partselectcom.azureedge.net/Schematics/Maytag/37313.gif

Glide and Spring Kit

PartSelect Number PS2017149

Manufacturer Part Number 205000

Manufactured by Whirlpool

Product Description

Glide and Spring Kit Specifications

This glide and spring kit contains two three inch springs, four one inch square glides, and two tubes springs. This kit replaces older style round roller glides.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting

This part fixes the following symptoms:

Burning smell | Will not agitate | Pumps but will not spin | Noisy

This part works with the following products:

Washer, Washer Dryer Combo.

This part works with the following brands:

Maytag, International, Jenn-Air.

Part # 205000 replaces these:

204998, 205000, 211952, 2-11952, 2-4998, 2-5000, 2791, 82-500, AP4023752, J28-652, Y204998, Y211952.
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Part Videos

Replacing your Maytag Washer Glide and Spring Kit

Customer Repair Stories
Average Repair Rating: 3.3 / 5.0, 5 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
dominic from weirton, WV
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Parts Used:
205000
The belts were not staying tight enough to agitate properly.
Firstly, remove ac power from washer!
After removing the front panel of the washer (two philips screws), I loosened and removed the plastic motor cover and removed three hex head screws holding the motor. Have someone help you tilt the washer so you can remove the belts by "rolling" them off of the pullies (pump pully and motor pully). What I did was use a chemical degreaser to clean the motor base metal channel where the nylon sliders reside. After doing that and letting it dry, I removed the two old
springs. I ended up reinstalling the old springs because they were not stretched and I installed a new spring (total three) on the right side of the mount. A stiff metal rod with a hook on the end will help you install the springs. Squirt some of the included silicone lubricant on both sides of the motor mount channel and exercise the lube. Reinstall the motor and plastic cover over top of motor. Clean hands and clean belts while you have them out, reinstall belts and front cover and you're finished. My wife said it never ran better!
63 of 68 people found this instruction helpful.
Was this instruction helpful to you?
David from Hartford, WI
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Parts Used:
12112425, 12112425, 205000
washer stopped spinng
I replace the belts - 5 min
I tried to replace the glides...I couldn't figure out how to do that..I took out the motor and and the glide mechanism...but I could not get glide braket separate from the motor mount..so i did not do this
I replace the springs and added 1 extra sping...3 instead of 2..it worked
54 of 70 people found this instruction helpful.
Was this instruction helpful to you?
Robert from Marlboro, NJ
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Parts Used:
WP22001650, WP22001320, 205000
Agitator action was slow/weak; Bleach tube kinked
UNPLUG THE MACHINE FIRST!
a) Remove the front panel (use a putty knife to release clips)
b) Fashion a small hook-end out of a coat hanger
c) Install an additional glide spring (2 + 1 = 3) to get extra retraction of vee-belt around drive pulley as follows.
d) Hook end of of the new spring onto rear (back) hole of moving motor mount (observe orientation of existing springs to be sure that you're hooking up spring into hole correctly).
e) Lie on your right side, hold the spring in place with your left hand (go around back of the motor with your left hand).
f) Have someone hold the flashlight as you take a coat hanger and fish for the front end of the spring under the motor glide.
g) With front - end of spring held by coat hanger hook, pull spring towards you and slip spring into front hole of stationary motor mount.
h) Lightly spray in and around glide area with Teflon non-stick dry lube (DuPont or Liquid Wrench dri-lube product line).
Machine agitates like-new now.
Bleach Tube:
a) Remove hose clamps at both ends using a screwdriver.
b) Remove and discard old tube.
c) Slip on the hose clamps and slicker-up the ends of new tube with palmolive liquid detergent and slip onto tub and bleach dispenser.
d)Tighten clamps.
25 of 35 people found this instruction helpful.
Was this instruction helpful to you?
john from COTTAGE GROVE, MN
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Socket set
Parts Used:
WP22001448, WP213045, 206638, 205000
leaking hoses and low tension on belts
opened front of washer, removed motor, replaced glides and springs, installed motor and replaced belts. Installed new hoses and vacuum breaker. Its been a week now and no leaks or other problems.
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Ginsbach from PHOENIX, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
205000, 12112425
No tub spin, burning smell.
Partselect.com gave me a very helpful list of parts per symptom. Said that there is an 88% chance that belts were my problem. Since the machine is 200 miles away I ordered two other parts as well. Belts fixed it! Took front cover off (not totally necessary). When the machine is tilted back belts are exposed underneath. Two belts later I was up and running. This site is really great.
1 person found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
4 Reviews
4.5
out of 5
Filter By Rating:
  • 5 Stars
    3
  • 4 Stars
    0
  • 3 Stars
    1
  • 2 Stars
    0
  • 1 Stars
    0
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Tension Springs -Set of 2
$6.36
PartSelect #: PS2016844
This is a set of 2 tension springs.
Grease
$4.57
PartSelect #: PS11738774
Model Cross Reference

This part works with the following models:

PartSelect Number: PS2017149
Manufacturer Part Number: 205000
Brand
Model Number
Description
Maytag
6329
Washer - MAYTAG AUTOMATIC WASHER
Maytag
6349
Washer - MAYTAG AUTOMATIC WASHER
Maytag
6359
Washer - MAYTAG AUTOMATIC WASHER
Maytag
A100S
Washer - Top Loading
Maytag
A101
Washer - Top Loading
Maytag
A102
Washer - Top Loading
Maytag
A102S
Washer - Top Loading
Maytag
A103
Washer - Top Loading
Maytag
A103S
Washer - Top Loading
Maytag
A104
Washer - Top Loading
Maytag
A105
Washer - Top Loading
Maytag
A106
Washer - Top Loading
Maytag
A106S
Washer - Residential
Maytag
A107
Washer - Top Loading
Maytag
A107S
Washer - Residential
Maytag
A108
Washer - Top Loading
Maytag
A108S
Washer - Residential
Maytag
A110
Washer - Top Loading
Maytag
A112
Washer - Top Loading
Maytag
A15CA
Washer
Maytag
A15CM
Washer
Maytag
A15CT
Washer
Maytag
A16CA
Washer
Maytag
A16CM
Washer
Maytag
A16CT
Washer
Maytag
A17CA
Washer
Maytag
A17CM
Washer
Maytag
A17CT
Washer
Maytag
A180
Washer - Top Loading
Maytag
A181
Washer - Top Loading