Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Mike W - January 10, 2019
Verified Purchase
Repair was easy
The diagnosis of the problem was difficult. The purchase and installation of the repair part was simple and seems to work. The cost of the part was $20 more than a service call with no parts.
★★★★★
★★★★★
Calvin L - August 23, 2018
Verified Purchase
Right part. Good price! Works well!
My wife is happy that her dish washer is working again
★★★★★
★★★★★
Dennis K - June 14, 2018
Verified Purchase
its alive
again. good price and it work
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.0 / 5.0, 2 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Dishwasher will not drain
Remove the water distributor, filtration plastic parts down to the base of the tub and clean of debris. Sometimes a small piece of plastic from the upper glass tray can break off and find its way into the bottom. Once its cleaned this section and be put back. Had to remove the unit from the cabinet and replace the drain motor and also cle
... Read moreaned the drain hose that runs to the garbage disposal. Most times this problem is caused by a blocked drain line or debris in the bottom of the tub constricting waster water from getting into the drain motor.
Read less
KEVIN from MURPHY, NC
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Our dishwasher would run for 1 min, stop then run for 1 min then stop completely.
We ordered a Control Panel first (not sure what part we really needed to fix the problem). After installation and the Control Panel didn't solve the problem, we knew we needed the Circuit Board. We then ordered the Circuit Board and upon receipt itstalled it. The Circuit Board was simple to install and BINGO! It worked perfectly. Tha
... Read morenk you for have the parts we needed.
Reynold Burbank
Read less
reynold from los angeles, CA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
47 of 90 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
11 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mary
July 25, 2019
Only one cycle works and numbers showing remaining time in cycle don’t show
For model number MDB7601AWQ
Hello Mary, Thank you for the question. Normally this would indicate a defective control board that needs to be replaced. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Tom
April 18, 2018
The digital options on top of lid do not work or light up.
For model number MDB7601AWS
Hi Tom, Thank you for the question. This sounds like an issue with the Control Board. In order to provide the correct part number, we will require the serial number of the appliance to determine the correct series board. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Chuck
January 14, 2020
All buttons on the control panel light up, except the start button. Reset the breaker, disconnected and reconnected all fittings on the control board. Still no start. Acting as if there is no power to the start button. Any ideas?
For model number MDB8951AWW
Hello Chuck,
Thank you for your question. Our sources suggest replacing the door switch under part PS11747715 for your model to fix the control panels issues. We hope this helps.
Hi, i have a Maytag dishwasher model mdb7601aws, the digits on control on front door are scrambled and won’t start any cycle. Is this a control board problem?Thanks
For model number MDB7601AWS
Hello Carmine, thank you for your question. Yes, that would be a control board issue. We would recommend replacing that part. There are different boards based on your serial number. Please resubmit this question with the model and serial number and we will advise which board you need. I hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Carmine
March 13, 2020
I called to order the part this morning and they told me it was part ps11750570 but your saying ps2004005 is the right one. Which is it?
For model number mdb7601aws sn is 33531984jj
Hello, Thank you for your question. You will need Part# PS11750570. I apologize for the inconvenience. We hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Carmine
March 6, 2020
What is the correct control board pn? thanks
For model number MDB7601AWS and Serial: 33531984JJ
Hi Carmine, thank you for your question. This would be the correct control board with your serial of model: PS11750570. Good luck with your repair.
Hello Janis, Thank you for your inquiry. We would recommend checking the following parts to fix your issue: heating element, control panel console and control board. You can test the parts with a multimeter. If you are unfamiliar with how a multimeter functions, there are YouTube videos available to assist you. Hope this helps!
Was this helpful?
Thank you for voting!
Jiri
August 6, 2019
Dishwasher starts and runs for around 15 minutes then stops. Doesn’t start again. It does this on every cycle.
For model number MDB7601AWB
Hello Jiri, thank you for your question. This issue could be caused by a few things. We would recommend testing the PartSelect Number: PS11748595 turbidity sensor, and thermostat PartSelect Number: PS11747691 first. If those parts are fine, the issue is most likely with the electronic board. I hope this helps!
Was this helpful?
Thank you for voting!
Nell
November 13, 2019
Buttons light up but does not start. Door latch was broken and replaced but still does not start.
For model number MDB8951AWW
Hello Nell, Thank you for the question. If the latch and switches were replaced, you may need a new Electronic Control Board, PartSelect Number PS2004005. Hope this helps!
Was this helpful?
Thank you for voting!
Carmine
March 12, 2020
The model is mdb7601aws the sn is 33531984jj what is the correct control board pn? Thanks
For model number mdb7601aws
Good Day Carmine. Thank you for your question in regards to your unit (Model Number MDB7601AWS). Based on our research the PartSelect Number for the Electronic Control Board that is compatible with your unit is PS2004005. You can order this part either online at our website www.PartSelect.com or by calling us by phone at 888-260-4310. Best Regards.
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
