This part is snapped onto the top portion of the evaporator. The thermostat sends temperature information to the processor. The defrost heater must be replaced when replacing the thermostat.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Amana Refrigerator Defrost Thermostat Kit
Troubleshooting
This part fixes the following symptoms:
Fridge too warm | Freezer not defrosting | Freezer section too warm | Freezer too cold
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Johnny S J - November 11, 2022
Verified Purchase
Perfect
Excellent trouble shooting tips, fast delivery of correct part and the install videos are really helpful.
★★★★★
★★★★★
Micah M - August 31, 2018
Verified Purchase
Got the exact part I needed
Got the exact part I needed quickly with the knowledge to back it up. I got a cold refrigerator in no time!
★★★★★
★★★★★
Bruce F. A - June 9, 2018
Verified Purchase
defrost problems
Part got sent all around before it was delivered. installed easily and fixed my defrost problems .
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.7 / 5.0, 13 reviews.
What's this?
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Fridge warm, freeze cold.
Thermostat kit it only had one connector. Fortunately I had a small wire nut that I used on the other wires.
Donald from OMAHA, NE
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Defrost thermostat failed causing ice build up
Once I figured out where the part was located it was quite simple. I thawed out the freezer first. Using a nut driver, I removed all the screws to the back panel of freezer. Squeezed the clips on the ice maker attachment to release the panel. Once I opened the panel the thermostat was visible and accessible. The failed thermostat was obvi
... Read moreous by its bulging appearance. By following the instructions found on Partselect.com, I cut the two connecting wires and removed the failed part. I then striped some insulator from the wires to connect the new part. I used electrical tape to ensure connection and insulation as the white wire connectors did not work well (too big) for my application. Closed everything back up, plugged in refer and all was good. A little time and a $20 part saved me $150. Thanks Part Select!
Read less
Gwen from Vista, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
11 of 15 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fridge was warm.
Removed timer. Tested timer with a continuity tester-seemed ok. Checked heater element-30 ohms-checked ok. Defrost thermostat measured 53k ohms when it was cold or warm. Should be open at room temperature and closed when cold. Part Select recommended changing the heater when you replace the thermostat. I was not able to slide the he
... Read moreating element out of freezer coils without removing coils. Put the old element back in. Seems to work ok. Thanks.
For the timer, I removed the upper light panel in the refrigerator with a screwdriver and the defrost timer is just plugged in. Easy fix, however most websites were saying it was located down by the kickplate. The thermostat was I think was te real culprit of my problem. I removed the back plate of the freezer after removing the pullout d
... Read morerawers. It just took four screws. The vent/grill just pops out if squeeze it to one side and slide out the other. Then swivel out door. Note that I do not have the ice maker installed in mine so yours may have a another step. I unplugged the refrigerator at this point and grabbed my blow dryer. I melted all the ice that had formed on condenser. The thermostat is located to the right of the fan. Unclip old thermostat and snip wires with enough slack to attach new one. Attach with wire nuts, reclip and start moving in reverse back to the beginning. 7days and no problems!
evaporator coil in freezer section fozen solid, refer not cool
To remove freezer door, push white tabs, inside rail toward back, remove door and rails as one unit. Unscrew plastic rail support on one side, remove ice maker, then back panel. Cut off thermostat, strip old leads, match colors, twist copper wires together, then crimp on new part using connectors provided. Reassemble, hardest part was
... Read morefiguring out how to remove freezer door. Check for continuity between heater lead and white terminal of icemaker plug just to make sure the heater is good while everything is apart.
Read less
Michael from Tucson, AZ
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
10 of 16 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Defrost not working
There were three parts in question, the defrost timer (inside the casing near the control dial at the top of the refridgerator), the defrost thermostat (behind the back wall of the freezer), and the heater coil (ditto). We tested the defrost timer by opening it up, advancing it to the defrost cycle, and waiting for the compressor to star
... Read moret up again, showing that the timer was working. Then we replaced the defrost thermostat and found that the heater coil worked.
The hardest part was figuring out how to open the casing and get to the timer. If I do it over again I will replace the $20 thermostat first and then deal with the timer if necessary. To get to the thermostat you can easily take the freezer door off by removing two screws in the door tracks. There was even an arrow pointing to one of the screws! Take out the food trays and then unscrew the back wall with a nut driver. The thermostat was clipped to one of the copper freezer tubes. I unplugged one end of the thermostat circuit at the lead to the heater coil and then cut the thermostat out of the circuit and used wire nuts to connect the new thermostat.
Read less
Glenn from Santa Rosa, CA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
11 of 15 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Back of freezer froze up and not getting cold in refrigertor.
I got on the web blog and saw a conversation on here that sounded just like the problems i have been having with my unit. After reading every thing about it i ordered the part needed and installed it. I let the fridge thaw out over night and started it up the next morning. Its been two month since i installed the part and it is working g
... Read morereat!!!
Read less
Dustin from Piedmont, OK
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
8 of 14 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Defrost failed. Freezer icing up
(FYI, Amana model is re-labeled Maytag with similar model number)I earlier replaced the defrost timer but that didn't solve the problem, so I purchased a new thermostat and evaporator heater. The hardest part was figuring out how to remove the slide out freezer door to access the back panel. Simple once figured out: There is one small
... Read morescrew on each slide rail, facing outward, near the door. Remove each screw and the door section will pivot up and disconnect from the rail.
The next thing you have to do is remove one of the slide rail supports so you can remove the back panel. Slide the track all the way out and you will see three small machine screws securing the track to the side of the freezer wall. Remove. Then push in the plastic clasp (near the back of the compartment) and slide the plastic assembly forward and out of the compartment. Now you can unscrew and remove the back panel to access the thermostat and heater.
I checked the resistance of the existing heater and measured 300 ohms (it would have been an open circuit if it was burned out). When I saw the resistance was OK on the heater, I left it in place and only changed out the thermostat. The defrost has worked fine since. Good luck.
Removed shelf drawer. Then removed plastic coverings from back panel of freezer. Squeezed tabs of ice maker connector to push it behind the back panel. With nut driver, removed the four screws holding the panel and removed the panel. Used a hair dryer to remove frost from upper right area that contains the defrost thermostat. Cut out t
... Read morehe thermostat and removed the connector on the right from the defrost heater. Removed brown wire from a few of the clips. Attached orange wire from new thermostat to orange wire leading to connector removed from defrost heater and the brown wires to each other using the pliers and supplied crimpable wire nuts. Wrapped the connections with self fusing tape. Reconnected the wiring to the defrost heater and clipped the new defrost thermostat to where the defective one was removed. Used the hair dryer to melt the ice that was covering the drain, then a turkey baster to unclogg the drain. Put everything back together.
Read less
james from southampton, PA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
77 of 91 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Auto frost not working correctly
My Freezer would only auto defrost occasionally and I first thought it was the defrost timer. But after reading posts on this website I looked deeper and found that my Defrost thermostat was bulging out. That didn't seem right just by looking at it. I read an earlier post and figured that must be it. I received the part and did the re
... Read morepair in about 15 minutes just had to cut two wires and reconnect with wire nuts and clip thermostat back onto the copper tube. Works perfectly now!
Read less
Mike from Milwaukie, OR
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
5 of 8 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
7 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kirk
January 4, 2018
My refrigerator and freezer are too cold and the thermostat adjustment inside the refrigerator compartment will not adjust the temperature any warmer (i.E. The refrigerator compartment is too cold). Would the defrost thermostat be an appropriate part replacement for this issue or should I look at another solution?
For model number ARB2217CSR
Hi Kirk, Thank you for the question. I suggest testing the thermostat. The best way to do this is to remove the thermostat from the refrigerator so you can control the temperature of the sensor. You can let the sensor warm up to room temperature. With the sensor warmed up to room temperature the sensor should read approximately 6.2K Ohms at 68°F. With the thermistor submerged is a glass full of ice water, the sensor should be very close to 32°F which should read approximately 16.3K Ohms. If the values that you are getting are far off from these readings, then the sensor is bad and should be replaced. Hope this helps!
10 people found this helpful.
Was this helpful?
Thank you for voting!
David
March 4, 2019
The door to the fridge was cracked open unknowingly for several days and now the refrigerator is cooler than room temperature but is not cold. The freezer is working correctly. From online research, which i'm not sure is correctly, it seems like the fan that is supposed to circulate the air from the freezer to the fridge is probably broken. Which is the part that i need to purchase and replace. Thank you.
For model number ABC2037DEQ
Hello David, thank you for your question. Yes, the fan motor should move air through from the freezer to the fridge. If the freezer is cold but the fridge is warm we would recommend testing/replacing the evaporator fan motor, damper, damper and thermistor. We would also recommend testing the defrost thermostat, heater and electronic board. I hope this helps.
6 people found this helpful.
Was this helpful?
Thank you for voting!
Ai
July 10, 2019
Why does the defrost heater need to be replaced when replacing the defrost thermostat ?
For model number MBB2256GES
Hello Ai, thank you for your question. I don't believe the heater HAS to be replaced as well, but sometimes both parts can fail at the same time. To be sure you don't need the heater, test it before placing the order. Set your multitester to the R X 1 scale. Place the tester's leads on one terminal each. This should produce a reading anywhere in between zero and infinity. If your multitester produces a reading of zero, or a reading of infinity, then your defrost heater should most definitely be replaced. There are many different kinds of elements, and so it is difficult to say what exactly the reading should be for your defrost heater. But it definitely should not be zero or infinity. If it is, replace the mechanism. I hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Marcus
November 16, 2018
The defrost thermostat kit apply to this refrigerator? Someone said there is a board. That replaces this and cost $250
Hello Marcus, Thank you for the question. Checking the model number, I am showing the appliance takes both the thermostat and the board, PartSelect Number: PS11738538.Thank you for your inquiry, good luck with this repair!
Il frigorifero funziona bene però si interrompe il compressore così all'improvviso aprendo la porta del frigo riparte e torna in temperatura si interrompe senza apparente motivo quando funziona il freezer arriva anche tranquillamente a -19 gradi così si spegne all'improvviso e trovo produttore di ghiaccio pieno d'acqua anzi acqua ghiacciata secondo me punto di vista potrebbe essere la scheda elettronica che non fa il suo dovere
For model number G32026PEKS
Ciao Gian, grazie per la domanda. Suggeriamo di controllare il termistore. Puoi testare il termistore per vedere se è difettoso. La resistenza del termistore nell'unità dovrebbe essere di 2,7K ohm a 77 gradi. Spero questo sia di aiuto!
My fridge is freezing my fresh food content, although I put the temperature controller in the lowest mark. So is this piece will help in my problem. Thank you
For model number 59662222200
Hi Rodolphe, Thank you for the question. I suggest testing the thermostat. The best way to do this is to remove the thermostat from the refrigerator so you can control the temperature of the sensor. You can let the sensor warm up to room temperature. With the sensor warmed up to room temperature the sensor should read approximately 6.2K Ohms at 68°F. With the thermistor submerged is a glass full of ice water, the sensor should be very close to 32°F which should read approximately 16.3K Ohms. If the values that you are getting are far off from these readings, then the sensor is bad and should be replaced. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Michel
November 8, 2021
Can you tell me what is the temperature spec on this thermostat: PS2003451, the original part I need to replace is 45-30f
thanks
For model number PDS22SBNBS
Hello Michel, thank you for your question. This defrost thermostat opens at 42°F and closes at 30°F. We hope this helps.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
