Average Repair Rating: 2.7 / 5.0, 2 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Icemaker fill tube cracked
The factory installed fill tube was formed and molded, hard plastic. Nothing like the replacement part or the one depicted in the install instructions.To remove it, I had to grip the exterior water tube module with a pair of Visegrip pliers, twist and pull as hard as possible, to expose a section of fill tube. I then had to cut through th
... Read moree tube with a hacksaw to remove the module and flange that secure it to the access hole. From the inside, I removed the ice maker and fan shield to expose the remaining section of fill tube. Using a section of copper pipe and a hammer, I was able to drive the tube through the back wall of the appliance. Fitting the new tube was easy. However, it is too short to reach the fill cup. I fashioned a section of the old tube to create an extension which I inserted in the new part. And, much to my surprise, it actually works!
Read less
Mark from SEBASTOPOL, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
5 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
leak from back of refrigerator where water line enters ice compartment
replaced old water fill tube for ice maker because it would clog with frozen water which would result in leaking from back of refrigerator where water line for ice maker entered refrigerator. Parts arrived faster than anticipated from parts select. New part was made differently (up-graded) so that water would not freeze. removed old fill
... Read moretube and replaced with new. replaced water tubing and secured. leak is no longer present and I do not anticipate further issues from this problem. Thanks Parts Select
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mark
July 22, 2017
How do you remove the ice maker fill tube (#12001935)? The exterior flange has no screws holding it to the rear panel. Is it brute force or is it fastened internally? Thank you so much.
For model number RCE224RDA
Hi Mark,
Thank you for the great question. You should be able to just use your strength to remove it from it's place.
I hope that helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Pete
May 2, 2019
I received the ice maker and installed with no problem to resolve water leaking into the freezer compartment. Water is leaking some ware and running downward at the back of the inside of the freezer. I am not sure what part to order. Any ideas? Thanks
For model number MSD2456GEW
Hello Peter, Thank you for the question. I suggest checking the water valve. It could be sending water to the ice maker when it is not suppose to and causing it to over fill and leak. You can also check the water lines going from the valve to the ice maker to see if they are damaged and leaking. Hope this helps, good luck with this repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Fred
September 5, 2019
How do i remove ice maker fill tube p/n 12001935, on Maytag refrigerator msd2756aew. Thank you.
For model number Msd2756aew
Hello Fred, Thank you for the question. The fill tube just pulls out of the hole from the outside of the appliance. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Wayne
November 28, 2019
How do I remove the old grommet on fridge, and install the new icemaker fill tube # ps2003449? There are no hole to mount it as shown in your video.
For model number RTD1900DAB
Hello Wayne, Thank you for the question. The Grommet should just push out of the hole. Hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
