Maytag/Maytag_Thumb/59115.gif
See part 5 in the diagram
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 10PM EST

customerservice@partselect.com

Drive Belt and Motor Isolator Kit

★★★★★
★★★★★
7 Reviews
$ 24.91   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS2003327
Manufacturer Part Number 12001788
Manufactured by Whirlpool
Product Description

Drive Belt and Motor Isolator Kit Specifications

This kit contains a flat drive belt, two motor isolators, and an instructions sheet. The drive belt is made to slip on the pulley until the basket gets up the desired speed.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Noisy | Pumps but will not spin | Burning smell | Will not agitate
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Maytag, Crosley, Amana.
Part# 12001788 replaces these:
AP4009041, 785411, 12001435, 12001788, 12001788VP, 22002040, 22002313
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

3 questions answered by our experts.
    Sort by:
    Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
    Edwin
    September 5, 2019
    Pumps water out but does not seem to agitate or spin. Error code indicates motor not running properly. But it sounds like the motor is running.
    For model number MAH5500BWQ
    Good Day Edwin. Thank you for your question in regards to your unit (Model Number MAH5500BWQ). Based on our research you may need to replace one or more of the following parts: 1) Drive Belt and Motor Isolator Kit (PartSelect Number PS2003327). 2) Motor and Control Board Conversion Kit (PartSelect Number PS2003515). You can order these parts either online at our website www.PartSelect.com or by calling us by phone at 888-260-4310. Best Regards.

    3 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Maggie
    July 19, 2019
    Was make loud noise when spinning but now it wont empty or even start
    For model number MAH5500BWW
    Hello Maggie, thank you for inquiring. You will most likely want to replace the Drive Belt and Motor Isolator part PS2003327 for your model. Good luck with your repair!

    2 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Deborah
    November 30, 2018
    My washer would make loud noises sounding like alot of marbles or change when the spin cycle would run, now my clothes do not spin dry they come out soaked
    For model number MAH5500BWW
    Hello Deborah, Thank you for your inquiry. We would recommend checking the following parts to fix your issue: Lip Seal Kit, Drive Belt and Motor Isolator kit, Spinner Support and Seal kit, Drain pump, and check the drain hoses for any obstructions. Hope this helps!

    1 person found this helpful.

    Was this helpful?
    Thank you for voting!
      Part Videos

      Replacing your Maytag Washer Drive Belt and Motor Isolator Kit

      Customer Repair Stories
       Average Repair Rating: 2.7 / 5.0, 11 reviews. What's this?
      Sort by:
      Sorry, we couldn't find any existing installation instruction that matched.
      Drains but doesn't spin, door lock does not engage.
      Door locked light did not come on and did not have 120 VAC across the Wax Motor. Also the Wax Motor did not extend out to make contact with the Door Lock, Spin Enable Switch. General guidance is to replace drive belt and to replace Wax Motor along with the Door Lock, Spin Enable Switches (total of two limit switches). This did not correct the problem. Checked for power and traced loss of power back to the Control Board where resistor R11 was found to be burnt out. Replaced Resistor with new Carbon Film unit, rating of 3.9 K-ohms, 1/4 W and 5%. As a prcaution, replace the Triac (manufactue part number NTE5657), component identified as Q6, rating of 0.8 Amp, 600 VAC. Semiconductor parts must be obtained from somewhere other than Parts Select (unable to find in the small town I live in, I located on the internet at Mouser.com). Unit works great now.
      100 of 140 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Belt wore off and broke
      Opened the back panel of the washing machine. Removed the old belt and wrote down the part number. Shopped online for a suitable replacement and found a perfect match at part select.com. I put in an order and it was delivered in a couple of days! I opened the back panel of the washing machinie again. This time I decided to also replace the isolators that came with the kit. For this, I had to unscrew the motor and gently tug it free. I placed it on the floor of the washing machine. I then replaced the 2 isolators as described in the kit, reinstalled the motor and put the screw back on. I then proceeded to place the belt on the motor and on to the wheel. This took couple of tries to get the grooves right. I then tested the washing machine on a rinse cycle and things looked good. Its been working fine so far.
      • DANIEL from WEST CHESTER, PA
      • Difficulty Level:
        Easy
      • Total Repair Time:
        Less than 15 mins
      • Tools:
        Wrench (Adjustable)
      • Parts Used:
        12001788
      37 of 44 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Loud noise when in spin dry
      This kit came with instructions. I followed them closely. The only thing I could add is clean the tub spindle with steelwool to remove any debris or rust. then wipe down spindle to remove all steelwool particles and follow instructions to reassamble.
      • Michael from Orland Park, IL
      • Difficulty Level:
        Difficult
      • Total Repair Time:
        More than 2 hours
      • Tools:
        Nutdriver, Pliers, Screw drivers, Socket set
      • Parts Used:
        22004465, 12001788
      32 of 35 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Drive belt sqeaked and contiued to roll off the drum.
      Removed washer back panel (after unplugging unit). Installed new belt. Reinstalled back panel. Belt wAs very tight getting it to roll onto the drum.
      • Douglas from Marion, IN
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        Less than 15 mins
      • Tools:
        Screw drivers
      • Parts Used:
        12001788
      12 of 18 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Ancillary Work when Replacing Noisey Tub Bearings
      The replacement for the drive belt and dispenser bezel were part of a bigger job of changing the outer tub bearings. Those familiar with Maytag Neptune washers will experience the jet-taking-off sound when the tub seals wear and water gets into the bearings. While I would have the machine open I thought I would change the drive belt. I also noticed the dispenser bezel had two of the four mounting corners broken.

      Replacing the bearings was done. I purchased the bearings and rented a bearing puller made especially for this job

      After the bearing and seal replacement, I put on the new belt. It was almost straight forward. Almost because the belt didn't just slip on. The new belt is much smaller than the old belt. Not having the grip strength of Mr. Atlas, I was not able to hold the belt on the pulley rim while turning the pulley around, as the instructions say. The other thing that makes this difficult is that the ribs on the outer tub are quite close to the spokes of the pulley. I was not able to firmly grasp around the belt and pulley with one hand and turn the pulley with the other. My knuckles seemed to get in the way (ouch!).

      Being an electrical engineer, I happen to have cable ties handy. I used one to hold the belt on the pulley rim, and was able to turn the pulley with two hands (still watching out for my knuckles).

      For the dispenser bezel, I took the old dispenser lid and hinge pins off the old bezel by cutting the bezel between the hinge points, then transferred them on the new one.

      On the washer top cover, there was a lot rust around the dispenser opening. So before closing up the machine and installing the bezel, I removed the loose rust, then applied a rust converter. The rust converter was in an aerosol can, and since I was working on the washing machine inside the house and not wanting to make a mess, instead of spraying the cover, I sprayed onto a paper towel then dabbed the chemical onto the rusty spots. I finished with an appliance epoxy paint around the dispenser opening.

      I'd like to say I was impressed with the service from PartSelect. I ordered on Saturday, they shipped on Monday, and the parts arrived on Tuesday morning, and this was with standard shipping. On Thursday I was ready to put on the belt, but there was also a problem where one of the motor isolators was missing from the belt kit. I called in the shortage and they shipped the next day and the new belt kit arrive on Saturday. I noticed the shipment was from Fresno so they must have a warehouse there.

      So all in all, the drive belt and dispenser bezel were simple to install. Certainly they were the easiest parts of the job.
      • Glenn from San Jose, CA
      • Difficulty Level:
        Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Screw drivers, Socket set, Wrench set
      • Parts Used:
        22002290, 12001788
      12 of 19 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Water Leaking Into Drum When Machine Is Off
      Removed the front door screws & front panel screws, removed screws in the "l" brackets holding the top down, tilted the top up & back, removed 3 hoses & 3 wire connectors from the old water valve. Removed 1 screw holding valve & replaced with new valve. Re-connected 3 wires & 3 hoses, replaced top & front door. While the machine was out from the wall, removed the back loovered cover, removed the old belt & removed 1 bolt holding motor. Removed th e motor, removed & replaced the 2 plastic insolators with the new ones supplyed with the belt on the motor spindels, re-installed the motor & bolt, then the new belt that is self adjusting. Replaced back cover & put machine back online, easy deal for anyone with very basic mechanical knowledge
      • SHANE from NUEVO, CA
      • Difficulty Level:
        Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
      • Parts Used:
        WP22002795, 12001788
      9 of 12 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      bad pump
      I took off the rear panel and removed the hose clamps and electrical terminals, slid pump out of slot in bottom pan of washing machine. It only took minutes, this was part of a major overhaul. I replaced this as a precautionary measure. Great prices and quick service,
      6 of 11 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Washer was so loud in the spinning cycle it sounded like a jet was taking off
      We took the washer completely apart. Replaced the bearings, pulley and
      belt. We decided to replace anything that involved the spinning cycle while we had it all apart.
      It was well worth the time and effort we put into it. It works like a chime
      and is very quiet . Silence is golden ! Hopefully it will work another 18 years.
      • Loanne from W BROOKFIELD, MA
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        More than 2 hours
      • Tools:
        Screw drivers, Socket set, Wrench (Adjustable)
      • Parts Used:
        22002315, 12001788
      2 of 2 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Burn smell during spin cycle.
      I followed the instruction of using a tie strap to secure belt to drive pulley and turn pulley to place belt on pulley. Worked great. Done in no time.
      • David from FOLSOM, CA
      • Difficulty Level:
        Very Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Screw drivers, Wrench (Adjustable)
      • Parts Used:
        12001788
      2 of 2 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      sharp metal edges
      after cutting my hand I installed masking tape around the opening on the back of the washer. All went well after that
      • William from CHINA, ME
      • Difficulty Level:
        Easy
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Nutdriver, Wrench (Adjustable)
      • Parts Used:
        12001788
      2 of 4 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Customer Reviews
      Average Rating:
      ★★★★★
      ★★★★★
      7 Reviews
      2.9
      Filter By Rating:
      • 5 Stars
        3
      • 4 Stars
        0
      • 3 Stars
        0
      • 2 Stars
        1
      • 1 Star
        3
        Sort by:
        Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
          Model Cross Reference
          This part works with the following models:
          PartSelect Number: PS2003327
          Manufacturer Part Number: 12001788
          Brand
          Model Number
          Description
          Crosley
          CAH4205AWJ
          Washer - Residential
          Crosley
          CAH4205AWW
          Washer - Residential
          Maytag
          MAH14PDAAL
          Washer - Commercial
          Maytag
          MAH14PDAAQ
          Washer
          Maytag
          MAH14PDAAW
          Washer - Commercial
          Maytag
          MAH14PDABL
          Washer - Commercial
          Maytag
          MAH14PDABW
          Washer - Commercial
          Maytag
          MAH14PDAEW
          Washer
          Maytag
          MAH14PDAGW
          Washer
          Maytag
          MAH14PDBAW
          Washer
          Maytag
          MAH14PDBEW
          Washer
          Maytag
          MAH14PDBGW
          Washer
          Maytag
          MAH14PDCBQ
          Washer
          Maytag
          MAH14PDCBW
          Washer
          Maytag
          MAH14PDDWW
          Washer
          Maytag
          MAH14PDSAW
          Washer
          Maytag
          MAH14PNAEW
          Washer
          Maytag
          MAH14PNAGW
          Washer
          Maytag
          MAH14PNAWW
          Washer
          Maytag
          MAH14PNBAW
          Washer
          Maytag
          MAH14PNBEW
          Washer
          Maytag
          MAH14PNBGW
          Washer
          Maytag
          MAH14PNSAW
          Washer
          Maytag
          MAH14PRAWW
          Washer
          Maytag
          MAH14PSAAW
          Washer - Commercial
          Maytag
          MAH20PDA3W
          Washer
          Maytag
          MAH20PDAWQ
          Washer
          Maytag
          MAH20PDAWW
          Washer - Commercial
          Maytag
          MAH20PDCXQ
          Washer
          Maytag
          MAH20PDCXW
          Washer

          Get in touch, we're here to help!

          Open until 10PM EST

          Contact Customer Service