If the microwave exhaust fan is not circulating air properly, there could be an issue with the grease filter. A dirty filter will cause your microwave to run less efficiently and can alter the taste or smell of your food. Filters should be changed every six months for maximum performance. These silver, aluminum filters are sold separately, and are approximately 13 3/8 inches long x 5 7/8 inches wide. Measure your current filter to assure correct replacement. Check your grease filters regularly for particles and grease buildup to see if cleaning is necessary. If there is any visible damage to the filter, it should be replaced straight away.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Nathan H - March 25, 2019
Verified Purchase
Good
As expected
★★★★★
★★★★★
Barbara B - February 20, 2019
Verified Purchase
Microwave Filter Screens
The filters fit perfectly and arrived quickly. First time we’ve purchased charcoal filters. Hoping they will help with cooking odors.
★★★★★
★★★★★
Pauline W - January 28, 2019
Verified Purchase
Really Fast Delivery
Your website is easy to use. I found the part I needed and received it very quickly.
Thank You!!
★★★★★
★★★★★
Linda P - September 27, 2018
Verified Purchase
Easty to order and replace.
The part fits below the microwave. No problem with the install.
★★★★★
★★★★★
JULIA S - August 15, 2018
Verified Purchase
Replacing the unexpected!
Had to buy this because after cleaning an existing one, I dropped it behind the stove while trying to install it...can't reach the dropped one. The new looks just like the old; shipping was prompt. I do think the change to a universal part for multiple stove models resulted in overall dimensions being slightly smaller, was difficult to get it to stay in place.
★★★★★
★★★★★
Keith G - August 7, 2018
Verified Purchase
Easy to install
Received In record time , and replaced the orginal in a couple of min.
★★★★★
★★★★★
RICHARD F - June 14, 2018
Verified Purchase
Part was wrong for microwave did not fit
Part wrong for microwave, part would not fit and did not match up with old filter
★★★★★
★★★★★
Gerald L - April 13, 2018
Verified Purchase
happy camper
fast service, arrived in great shape. very good instruction for installing.
★★★★★
★★★★★
Debbie T - April 4, 2018
Verified Purchase
Grease and charcoal filter
Easy to install both; took about 10 min total.
★★★★★
★★★★★
Stephen S - April 4, 2018
Verified Purchase
Easy to replace
Moved into a new house which was a rental. Grease filters were nasty. New one was easy to put in and much, much cleaner.
< Prev
1
2
Next >
Customer Repair Stories
Average Repair Rating: 4.3 / 5.0, 11 reviews.
What's this?
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Grease filters were missing from the over-the-stove microwave
Why a tenant would remove and discard the grease filters without replacing them is beyond me! But, I removed the filters from the package and slid them into place. Two minutes tops. I would like to add that I ordered these on Thursday afternoon, and I had them on Saturday; awesome customer service!
Lori from Salt Lake City, UT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
64 of 127 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Thought filters should be changed after 5 years of use.
Used hands to slide filters sideways, till they could be pried out with screwdriver or bare hands. When new parts arrived, easily slide new filters into position. In hindsight, we did not need to replace grease filter. I was able to clean one of those with ordinary dish soap, warm water, and a brush.
The repair was simple and easy. It required a Phillips head screw driver only. I Removed the vent grill and replaced it with the new grill there were only two screws that needed to be removed then refastened. Total five minutes. I also replaced the grease filters which took about a minute total time. I do many of my own repairs to my hom
... Read moree and appliances .I've found your service parts delivery prompt and precise.
I went online and found the manual for this appliance and used the instructions, which were very helpful. The filters just pop out and the new ones fit right in. No tools were needed. For the vent grill, it was necessary to move the metal tabs back and forth a few times manually before they were properly placed in order to take the two
... Read more screws, which hold the grill in place. I then loosely tightened the screws (so as not to crack the plastic grill)with a Phillips Head screwdriver. When my husband got up from his nap he was pleased to see the job completed without his help.:)
Slide grease filter about 1/2 inch to right (or left) using the d-ring attached to one side and then pull down and out. Push charcoal filter frame slightly to rear and pry down from front. Install new charcoal and grease filters by reversing process. No tools - 5-minutes max!!
Our Microwave Vent Grill was broken - and since I was ordering online, I figured I'd get the two filters as well. The Vent Grill was fairly easy to install. It was a little tricky getting it to fit in, but once in, it was just a matter of screwing in at the top.
The Filters were another matter. The FILTR-GRSE came out very e
... Read moreasy, but what I didn't realize was when I ordered it, it only came in packs of 1. The Charcoal Air Filter came in packs of 2, so I assumed both did. Why, when you need two of each of these, do they sell one in single packages - and the other in packs of two? The Charcoal Air Filters were only replaceable by unscrewing the bottom of the microwave. The FILTR-GRSE were easy enough to just pop out.
It was a simple replacement of grease filter and charcoal filter in microwave/hood combination. I did use a screw driver to pry out the filters, but otherwise no tools. It was easy and straightforward.
replace charcoal filters and grease screens and clean top exit ports
Removed old grease screens by sliding sideways and then pulling out of the grooves. (helps to have rubber gloves as the grease is slippery). Put pressure on the back of the charcoal filter rim and allow side closest to you to drop down slightly so you can get a fine flatblade screwdriver under and pop the filter out of the holder. Work
... Read mores same on both sides. Install new charcoal filters after cleaning the holder edges with soap and water and drying. Make sure charcoal filter is in the second set of holder grooves and snap in place. Replace new grease filters with the pull tabs down and facing the center. Slide the grease filter into the holder grooves a little further back than normal and (using the pull tabs) pull the filter back the other way until flush with the opening and in place. The top exit ports are removed by taking out 4 screws;however, two of them are attached to spring clips on the underside and it is easy to break off the tiny plastic ridges underneath. The other screws come out easily and the entire exit port piece can be removed and cleaned. To reinstall just snap exit port back in place and replace screws. If you have broken off the slender plastic ridges you can sometimes turn the screww a partial turn and engage what is left; if not you may have to put some rubber grommets or pieces to support the bottom and keep pressure on the exit port piece which is not locked by only two screws.
Ask our experts a question about this part and we'll get back to you as soon as possible!
9 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Sam
January 20, 2018
I need to replace the exhaust fan grease filters under the range on my Kenmore microwave. The exhaust has two grease filters. Does this part include two filters?
Hello Sam,
Thanks for your question. This part is sold individually.
I hope this helps.
6 people found this helpful.
Was this helpful?
Thank you for voting!
Jenette
February 25, 2018
Replacement filters for KitchenAid microwave are your filters oem or "off market" parts?
Hello Jenette, Thank you for your inquiry. All of our parts are OEM directly from the manufacturer. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Olly
September 1, 2021
Whirlpool microwave part 6802a filters is it a two pack
For model number YMH1141XBM-3
Hello Olly, Thank you for the question. The Filter is Sold individually. We hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Mary
February 13, 2022
What are the dimensions of this?
Hello Mary, Thank you for the question. According to the 1" Grid this filter is approximate 13" X 6". If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Frances
November 30, 2022
Which filter can I use
For model number MH1150XMT3
Hello Frances, thank you for reaching out. This is the compatible grease filter, part number PS1847969, for your given model. If you require assistance to place an order, please contact customer service. We hope that helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Anna-Marie
February 4, 2023
I need replacement air filters and grease filters for my 14 year old Whirlpool above-range microwave. Which ones will fit my microwave?
For model number YMH7155XMS-2
Hello Anna-Marie, We are glad you asked! The Charcoal Filter is PS382960. It sells as a package of 2 filters. The Grease Filter is PS1847969 and is Sold individually. We are pleased to have been able to help.
I need filter screens for my Whirlpool microwave the model for the microwave is mh3184xpq 4
What is the model number for the screens
Hello Sangita, Thank you for your question! Upon reviewing your model I show the part number for the grease filter is PS1957060 and the air filter is PS1871348. Good luck with your repair!
Was this helpful?
Thank you for voting!
Lewis
November 13, 2018
What is the plate called that is located on the top inside the microwave?
Hello Lewis, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the unit. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!
Was this helpful?
Thank you for voting!
Sally
July 4, 2023
Installation of grease filter
For model number MH1154XMT
Hi Sally, Thank you for writing. You just need to slide the grease filter about 1/2 inch to right or left using the d-ring and then pull down and out. The new filter will slide into place. We hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
