Motor and Drain Pump WH23X10028 | Official GE Part | Fast Shipping | PartSelect
Motor and Drain Pump – Part Number: WH23X10028
Motor and Drain Pump – Part Number: WH23X10028 Motor and Drain Pump – Part Number: WH23X10028 Motor and Drain Pump – Part Number: WH23X10028 https://partselectcom.azureedge.net/Schematics/GE/00122028i02.gif

Motor and Drain Pump

Product Description

Motor and Drain Pump Specifications

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This pump has sound isolation mounting washers and a filter.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting

This part fixes the following symptoms:

Will not drain | Pumps but will not spin

This part works with the following products:

Washer.

This part works with the following brands:

General Electric.

Part # WH23X10028 replaces these:

1394137, AP4324598, WH23X10026, WH23X10028, WH23X10037.
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Part Videos

Replacing your General Electric Washer Motor and Drain Pump

Customer Repair Stories
Average Repair Rating: 4.5 / 5.0, 3 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Trent from Shreveport, LA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Parts Used:
WH23X10028
Washing machine would cease functioning at the spin cycle and would not drain.
Remove the front coverfrom the machine. This is done by removing the 3 screws at the bottom of the panel. The panel then drops down and pulls straight off. The pump is located on the front right wall of the of the machine. You will notice a 2-3 inch diamete threaded cap on the right side of the front wall of the machine. This is the front of the pump and access to the filter. Place a large bucket under this cap and slowly loosen the cap. All of the water remaining in the machine will begin to drain (this could be a lot of water. Do not remove the cap completely so that you can quickly stop the flow of water if needed). Once all water is drained from the appliance, Disconnect the two hoses from the pump using a pair of pliers to looses the presure clamps, sliding the clamps back an then pulling off the hoses (be careful of any remaining water in the hoses). Then remove the two screws from the rear base of the pump that secure it to the bottom floor panel of the washer. Slide the pump slightly to the rear to free it from the fittings on the front wall of the machine and the lift the pump up. At this point, firmly pull out the wiring harness plugged into the top right side of the pump. Install the new pump by plugging in the wiring harness and resecuring the pump. Plug in the machine and run on the rinse and spin cycle to test.
137 of 157 people found this instruction helpful.
Was this instruction helpful to you?
John from Farnham, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Parts Used:
WH23X10028
pump would not pump water out of washer
I took the two drain hoses off with the pliers then only two screws that holds the pump. After that the two hot wires which are black and white. But remember to unplug you're washer since the pump is not grounded you don't want to risk being shocked. Hope thi helps. Plus i saved around 250.00 by repairing myself.
74 of 98 people found this instruction helpful.
Was this instruction helpful to you?
Nathaniel from HAWKINSVILLE, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Parts Used:
WH23X10028
Would NOT drain
Flipped washer on side
Did repair from bottom
Really easy repair
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
10 Reviews
4.7
out of 5
Filter By Rating:
  • 5 Stars
    9
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    1
  • 1 Stars
    0
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Model Cross Reference

This part works with the following models:

PartSelect Number: PS1766031
Manufacturer Part Number: WH23X10028
Brand
Model Number
Description
General Electric
GBVH5140H0WW
Washer
General Electric
GBVH5140H1WW
Washer
General Electric
GBVH5200J0WW
Washer
General Electric
GBVH5200J1WW
Washer
General Electric
GBVH5200J3WW
Washer
General Electric
GBVH5200J4WW
Washer
General Electric
GBVH5200K0WW
Washer
General Electric
GBVH5300K0WW
Washer
General Electric
GBVH6260F0GG
Washer
General Electric
GBVH6260F0WW
Washer
General Electric
GCVH6260F0GG
Washer
General Electric
GCVH6260F0WW
Washer
General Electric
GCVH6260H0WW
Washer
General Electric
GCVH6260H1WW
Washer
General Electric
GCVH6400J0WW
Washer
General Electric
GCVH6400J1WW
Washer
General Electric
GCVH6400J2WW
Washer
General Electric
GCVH6500K0WW
Washer
General Electric
GCVH6500K1WW
Washer
General Electric
GCVH6600H0BB
Washer
General Electric
GCVH6600H0GG
Washer
General Electric
GCVH6600H0MB
Washer
General Electric
GCVH6600H0MS
Washer
General Electric
GCVH6600H0WW
Washer
General Electric
GCVH6600H1BB
Washer
General Electric
GCVH6600H1GG
Washer
General Electric
GCVH6600H1MB
Washer
General Electric
GCVH6600H1MS
Washer
General Electric
GCVH6600H1WW
Washer
General Electric
GCVH6800J0BB
Washer