Also known as Bellow. The part may differ in appearance but functions same as original.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your General Electric Washer Door Boot Seal
Troubleshooting
This part fixes the following symptoms:
Leaking | Burning smell
This part works with the following products:
Washer.
Part# WH08X10036 replaces these:
AP4334050, 1394050, WH08X10022, WH08X10040
Customer Reviews
Average Rating:
★★★★★
★★★★★
8 Reviews
5.0
Filter By Rating:
5 Stars
8
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Charles C - July 24, 2022
Verified Purchase
Easy repair for doing it the first time. No more water leaking onto the floor!!!
Part was delivered in a reasonable amount of time and was the correct part for my machine.
★★★★★
★★★★★
Todd R - May 15, 2022
Verified Purchase
Worked great.
Quality part.
★★★★★
★★★★★
Janet R - July 11, 2020
Verified Purchase
Replace Door Boot Seal
This is the second time I've replaced this part. It's a super easy job -- anyone can do it! The second replacement was due to the spider arm breaking and that time we had to completely rebuild the washer -- it was worth it! Parts Select is so helpful, they have the parts, and their website is informational.
★★★★★
★★★★★
IRENE R - March 20, 2019
Verified Purchase
Door Boot Seal
It was the correct part. And the nicest thing about
your service was the video of the installation you provided.
Even if I didn't install it, at least I knew the extent of the
work.
Thank you.
★★★★★
★★★★★
William M - December 3, 2018
Verified Purchase
Ripped boot
The part was a quality part. Replacing was not really hard just need to have a little mechanical knowledge. The clamps are the worst part, once they’re on properly you’re all good
★★★★★
★★★★★
Angela S - November 22, 2018
Verified Purchase
Repair a bit tricky but part and service we're great!
Fast service and part works great!
★★★★★
★★★★★
William M - November 5, 2018
Verified Purchase
Great part, install difficult
The part was great and arrived promptly. A couple of the steps had me tearing out my hair. Removing and reinstalling the inner tension wire was a royal PITA!
I noticed that in the video that the camera cut away when the screwdriver was first applied to the screw to undo the tension wire. Presumably the camera cut away so as to not record the mandatory swearing required to get the screw undone. The concrete counterweights are absolutely positioned to prevent being able to actually unscrew the screw. I had to cut away the old bellows and try about 3 screwdrivers to get it undone.
Getting the bellows seated on the inner flange was another treat! That took a while...
Nonetheless, It was a good experience, and the leak at the door was stopped.
William M
★★★★★
★★★★★
Arturo B - January 31, 2018
Verified Purchase
easy repair!!
The part came fast my machine is back working!! Thanks
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 2.5 / 5.0, 13 reviews.
What's this?
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Front seal leaking water.
Took it apart per the video and reinstalled
Jodd from HANNIBAL, MO
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door boot seal tore and washing machine was leaking water
Watch the video posted on PartSelect. It was excellent and walked step by step through the whole repair.
I only ran into one issue not included in the video. In order to remove the inner ring holding the boot seal, I had to remove the weight at the bottom of the tub. This is easy to remove with a wrench, but took two people
... Read more to reinstall. You only need the second person for 1-2 minutes to hold the weight while you align the bolts.
The most difficult part is ensuring you replace the hex nuts and screws in the same location. I took pictures as i removed them to know where to reinstall.
Total repair time was probably 1.5 hours.
Read less
Paul from LAKEVILLE, MN
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Spider Arm
We ultimately rebuilt this washer because I love it so and it was one-half cheaper to rebuild than to buy new! We watched videos and researched the repair and then dove in. Yes, we had to tear the machine down but really it was not that bad of an ordeal. It ended up being much easier than we initially thought but once all the parts arr
... Read moreived we fixed it!
I won't bother repeating other people's comments. My repair took a bit over 2 hours. I watched 2 different videos and thought the repair was doable. To remove the first wire band holding the boot seal to the front panel I found using an awl to grab the eyelet near the spring was easier than using a needle nose recommended in the video.
... Read more To remove the second wire band I used an offset screwdriver. One video I watched recommended removing the lower counterweight to get at the band's screw - I did not do that. Putting the new boot seal into the first groove and installing the wire band was the most time consuming part of the job. I did not have extra hands to help. I recommend the second pair of hands for that part to save time. The rest of the install was easy.
Read less
Gary from WEBSTER, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
smoking in drum in rinse cycle
followed video on website
albert from CLIMAX, NC
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
6 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
leaky washer
we took the advice of you tube. my husband said "WONT READ DIRECTIONS BUT WILL WATCH A VIDEO" and he fixed it no problem. it took about 1 1/2 hours per unit.
nicole from round lake beach, IL
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
24 of 29 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The rubber gasket on my front loader had a rip in it and soap and water would leak out at the bottom making a nice puddle to walk in on.
I read and reread all of the installation repairs everyone had sent in. Everyone said on the average it would take 1-2 hours. I partly started the install myself and the ran into a problem. My wife was my helping second hands( second hands is a great help) and she suggested to either google or YouTube the repair. Within minutes I had fou
... Read morend one on you tube and it help me tremendously. it had the exact model washer on the video and the install was a breeze. I would recommend looking up the repair cause they show step by step video and makes it a lot easier.
Read less
Gerard from Pompano Beach, FL
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
101 of 118 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
rip on gasket (maybe from a caught zipper)washer leaked
I was able to get the 1st metal ring After trying everything to get the 2nd ring off I ended up calling a repairman. It was just too hard for me get my hand into the area to loosen the ring. It took repairman over 1 hr to complete job of installing the boot. After spending o$300, I just just shook my head. Hats off to the other people abl
... Read moree to do it.
Read less
Patrick from Linden, NJ
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
27 of 37 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The door boot seal gasket ripped during a load.
I took the outer retainer clamp off and pulled the outer seal off the front of the washer. Then pushed the seal inward to see the rear seal and its wire clamp. Took a philips head screwdriver (short handel) and loosened the clamp. Pulled the clamp out and then the rubber boot. Put new boot on the tub (rear - this took a little while to ma
... Read moreke sure the seal was correctly in place.) Make sure the boot is lined up with the two hose connections. Intstall wire clamp, this took some time because there is not a whole lot of room to get your hands in there to tighten. Connect the two hoses to the boot and the boot to the front of the washer. Install outer wire clamp. Done.
Read less
ben from newaygo, MI
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
48 of 62 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leaking from the door.
I had to replace the door gasket because there was a small piece that had torn away, which caused large amounts of water to leak when the load of laundry was too big. Smaller loads of laundry would just produce a little bit of water. Unsure of how to replace the gasket, I used a phillips screwdriver to pull the door and front panel
... Read moreoff. I thought that this would be pretty simple, but I soon discovered that it wasn't as simple as removing several screws and pulling the pieces off. The door was easy, the bottom panel was easy, but the front panel was held in place by screws, plastic tabs, the front of the gasket (I'll explain later), and gravity by means of plastic supports. Trying to find and release the tabs, lifting the panel up and out was not self-explanatory. I finally figured it out, and it made changing the gasket out, a breeze. The gasket is held in by two diferent wire spring clamps/bands. One band holds the gasket to the outside of the tub, and the other band holds the gasket to the front panel. Before removing the front panel you must remove the first band which is cleverly hidden by the face of the rubber gasket. Just peel it back...it's in there. I was able to pull/pry this off with a screwdriver because I was not worried about damaging the old gasket. The second band had to be removed with either a 6mm/7mm wrench(I can't remember which) or a stubby phillips screwdriver. The stubby screwdriver is handy because of the proximity of the tubs counterweights. Once the final band is removed just peel the gasket away from the tub, after taking note of how it came off. Put the fully loosened band on the new gasket and fit the new gasket into place. It helped to have two sets of hands to work it around the tub, but probably not necessary. The wrench is necessary to properly tighten the band, because you cannot get enough torque on the stubby screwdriver.Once the gasket is in place you can re-install the front panel, and secure the front of the gasket to the panel. Install the band and it will secure itself by the tension of the spring. Put the door back on and you are ready to wash clothes.
Read less
Brandon from Chugiak, AK
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers, Wrench set
219 of 256 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
19 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tyrone
September 1, 2017
I ordered washer door boot wh08x10036 and it didn't come with a band clamp. Did I order the right one if not can you give me the right part number.
For model number WCVH6800JOMS
Hi Tyrone,
Thank you for the question. You did order the correct boot for the model number but the clamp is sold separately. The part number for the clamp is 1019932.
Hope this helps!
Washing machine made a loud noise the seal between the tub and front door spun and twisted took the front spring loaded ring off in the tub lower than the door opening. Thought i could just been the seal back in place but the tub is about 2 inches lower i had to prop it up from the bottom to get to line up with the door. I think i have more than a seal issue. I need suggestions what to do next
For model number WBVH5200J1WW
Hello Joe,
Thank you for your question. I would actually suggest that you take the back panel off of your machine and take a look at your rear drum and bearing. It sounds like perhaps the Drive Pulley or Rear Drum assembly might have broken.
I hope that helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Val
October 22, 2019
Will this gasket fit the older model?
For model number WCVH6600H0BB
Hi Val, thank you for your question. Yes, this is the part that you are looking for according to your manufacturer and the model number provided. I hope that helps. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
John
October 29, 2017
Is this an original oem GE part?
For model number WH08X10036
Hi John, Thank you for the question. Yes all of our parts are OEM. Good luck with the repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Scott Uysal
March 24, 2018
I have seen so much smoke came out during spin cycle, plus when i open the front door i have seen little rubber pieces.
For model number WCVH6600H0BB
Hello Scott, Thank you for your inquiry. We would recommend checking the following parts to fix your issue: drive pulley kit, drive belt, motor kit, and door boot seal. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Hannah
January 10, 2018
Hello. The sheets in my washer did not ring out the necessary water after a cycle. It does this from time to time. I put it through an additional spin and drain cycle and when i came back the room smelled of burning rubber or possibly a strong gas smell. I had to open the garage door to air it out. I'm exploring what part would be the culprit and am wondering if it's the door boot seal. We also checked the belt in the back of the washer, but it seemed to look ok. How would i know if our door boot seal needs replacing? Is there a way to tell before taking it out? Thanks!
Hi Hannah, Thank you for the question. You would replace the Boot Seal if you had water leaking. It would not effect the appliance spinning out the water from the clothes or sheets.In order for us to locate the correct parts and repair information we will require the model number of the appliance. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Tony
November 16, 2018
I have this same problem as included below. Occasionally the washer gets a rapid knocking when spin drying so i stop it and restart it, which allows the cycle to complete without the rapid knocking. The barrel seems rigid (no movement/slop to indicate a bad bearing). Can you provide detail information on how to determine if a part is defective for each of the items you recommended checking? If all these parts are required, they will cost upwards of $600 for parts alone. If it is just a damaged (rotting?) door seal, then that is manageable." i have seen so much smoke came out during spin cycle, plus when i open the front door i have seen little rubber pieces.
scott uysal
march 25, 2018
answer:
hello scott, thank you for your inquiry. we would recommend checking the following parts to fix your issue: drive pulley kit, drive belt, motor kit, and door boot seal. hope this helps!"
For model number WHDVH660HW
Hi Tony,
Thank you for your question. A washer making a loud noise during spin cycle can also be caused by a faulty drive pulley. The pulley is what the belt (if applicable to your washer) rides on to spin your washers tub. The pulley can be made of plastic or metal. It could be simply worn out or just loose. The only way to know if the parts are defective is to inspect them and if they are electronic parts, you will need a multimeter to test them. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Wilbert
June 20, 2019
Are there any seal between the tub and the door gasket
For model number WBVH5200J1WW
Hi Wilbert, thank you for your question. No the seal would be the door bellow/tub boot seal. I hope that helps. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
David
May 5, 2018
Door boot bellows became twisted. Replaced it but tub doesn't line up with the opening in door and filler spout distorts the boot. Tub appears too low and off to one side. Thoughts?
For model number WCVH6800J0MS
Hello David, I would recommend watching the video that shows how to install this part on our site, under part number WH08X10036. It may be that the spring clamps are not holding the gasket onto the tub which allows the gasket to move with the Tub. I would suggest looking at the inner and outer bellow clamps. I hope this helps!
Was this helpful?
Thank you for voting!
David
May 7, 2018
Installed a new door bellows. The old one became very twisted while was still installed. When attaching the full tube at the upper left the bellows is almost too low. Attaching it causes the bellows to be pulled upward out of shape. When putting the door panel on the edges of the bellows where it should meet the opening in the door is off by about 3 inches. Is there a suspension part i should look for that failed that would cause the drum to drop twisting the original bellows and new bellows to not line up with door opening ? New bellows is in the tub grove and clamps seated properly. Door and tub do not align even without the bellows. Thanks.
For model number WCVH6800J0MS
Hi David,
Thank you for your question. For information on how to install the door boot seal, there is a video listed with the part on our website, that you may reference for help. I hope this helps. Thank you and have a great day!
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Washer","title":"Washer","url":"/Washer-Parts.htm"},{"position":2,"name":"Seal or Gasket","title":"Seal or Gasket","url":"/Washer-Seals-and-Gaskets.htm"},{"position":3,"name":"WH08X10036","title":"WH08X10036","url":""}]
You added 1 item to your cart
✖
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
