This Drive Belt is 89.5" long and comes in black, featuring four ribs on the inside for a better grip. This is a long belt that wraps all the way around the dryer drum, around a tension pulley, and then around the drive motor pulley, allowing all the parts to work together, spinning the drum as the motor rotates. If the drum will not turn when the dryer is turned on the belt is likely broken. It is common for belts to stretch or become brittle over time, which is what leads to the breakage. If broken, it should be replaced; the drum simply cannot spin without this belt. Refer to your model number and user manual to check if this part is right for you. Ensure you use work gloves to protect your hands from sharp internal parts during this repair. Please note: When comparing the length of your old belt to the length of the belt as stated here, remember that a small amount of stretching and contortion may occur with belts over time for a range of different reasons. Unless your belt is drastically different in length, this belt is what you are looking for despite any small inaccuracies. You will need to remove power to your appliance, remove the main panel, and access the motor drive to slip your new belt back into place.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your General Electric Dryer Drive Belt
Troubleshooting
This part fixes the following symptoms:
Noisy | Drum Not Spinning | Won’t Start
This part works with the following products:
Dryer, Washer Dryer Combo, Washer, Range.
This part works with the following products:
General Electric, Hotpoint, Kenmore.
Part# WE03X29897 replaces these:
WE12M0022, WE12M22, WE12M29, WE12M33, WE12X21574
Customer Reviews
Average Rating:
★★★★★
★★★★★
168 Reviews
4.8
Filter By Rating:
5 Stars
152
4 Stars
10
3 Stars
3
2 Stars
0
1 Star
3
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Brian P - 19 days ago
Verified Purchase
great part
arrived quickly
★★★★★
★★★★★
Pat L - February 26, 2024
Verified Purchase
Hassle free service
I originally ordered the wrong part but caught it the same day and the staff was able to cancel the part I ordered in error and get me this belt with no hassle. Ca
E quickly and fit perfectly.
★★★★★
★★★★★
Henry J - February 15, 2024
Verified Purchase
Correct part easy to install
See above
★★★★★
★★★★★
Ronald S - December 27, 2023
Verified Purchase
Easy repair
The part fit perfectly. Had my dryer back in service in no time.
★★★★★
★★★★★
Robert R - December 21, 2023
Verified Purchase
Perfect Fit
Perfect fit, fast shipping and great price!!!
★★★★★
★★★★★
Dwain B - November 28, 2023
Verified Purchase
Easy to fix
The dryer belt was exactly the right size and very easy to install. Had it back together and running in 20 minutes.
★★★★★
★★★★★
Thomad R - October 20, 2023
Verified Purchase
Good
Great
★★★★★
★★★★★
Rosemary D - October 6, 2023
Verified Purchase
Quick & easy repair
Part shipped fast and worked perfectly. Happy to do business with them.
★★★★★
★★★★★
Raymond A - September 10, 2023
Verified Purchase
Exact part needed.
Exact part I needed. Repair went as planned and part arrived as promised. Thank you.
★★★★★
★★★★★
Tara O - September 8, 2023
Verified Purchase
Great piece of foam
Great piece of foam
< Prev
1
2
3
Next >
Customer Repair Stories
Average Repair Rating: 2.8 / 5.0, 65 reviews.
What's this?
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Dryer was making increasingly loud "thumping" sound.
Parts were shipped quickly, packaged correctly, and were in original GM packages - very reassuring. BTW, your customer service is excellent. Reviewed YouTube videos. Patience is required, take your time, take photos of the wires and also make a written wiring chart. This was the flaw in my planning. Reference the schematics f
... Read morerom PartsSelect to number the controls. Do NOT use masking tape to identify the wires as they will have all stuck together by the time you go to reinstall them. Most difficult process was removing and identifying the numerous wires to the back panel. They have push connectors, but some were very difficult to remove. The people doing the "how to" videos no doubt had them partially released and that made it look easy. Examine the connectors before removing to identify how they are captured by the connector. A paper clip "tool" I made enabled me to release some of the capture lugs, but some were so tight, I had to use small needle-nose pliers to open up the lug to release the wire on the connector. When reinstalling, re-tighten those connectors. Replacing the parts was much easier than the wiring disconnect/reconnect process. I'm happy to report that replacing the rear bearing and the front 2 green and 2 white shim/bearings immediately and completely solved my problem. For about $150, I restored my dryer to "like-new" functionality and got a lot of satisfaction from doing it. The project took about 4 hours, which could have been reduced to 2 hours had I know about the clip release and wiring identification process. Also, make sure you thoroughly vacuum out your unit while it is disassembled. Good luck!!!
remove top of cabinet and front panel. placed belt around drum and replaced idler pully placed new belt around pully and was done. not a hard job at all. replced front panel and top. thanks to a speedy delivery of my parts dryer was only down two days.
The PartSelect company's "how to" repair videos are OUTSTANDING. Thank you! The videos provided a comprehensive overview of what to expect in terms of clothes dryer disassembly, component replacement and reassembly. The videos were invaluable tutorials for prior-to-disassembly work.
I ordered all the following parts which I fel
... Read moret were likely excessively worn--white and green bearing slides (two of each required), rear drum bearing kit, drive belt, and idler pulley wheel--to address the noisiness issue.
For your consideration: Since our dryer is 12 years old and would be disassembled anyway, I decided to order a new dryer drum belt and idler pulley, to replace these two constant-use items as preventive maintenance.
Two notes. One: When replacing the dryer drum bearing parts, you need a T25 torx bit to loosen and remove the three torx-head screws. But using my T25 torx bit-head-style screwdriver, it was impossible to loosen them. Fortunately, I had a T25 torx bit, which I could mount in a socket wrench, which DID allow me to loosen those three torx-head screws without damage/breakage. WHEW! Recommend you are similarly prepared! Two: If you purchase the "Rear Drum Bearing Kit," it already comes with the the "Drum Bearing Sleeve" and "Retainer O-Ring" components I thought I would also need--no need to purchase separately. I returned those two items, unopened, for a refund.
All together, from dryer disassembly to, component replacement, to a thorough vacuuming/cleaning, to reassembly and an operational check, it took about four hours. The dryer is now nearly noiseless again! Success!
I consider myself reasonably good with tools and have a fair amount of electrical and mechanical skill. My wife assisted with extra hands a couple times, too, seriously reducing my frustration level. Depending on your abilities, you'll take more time or less time than the four hours it took me. I'm certain I saved at least a couple hundred dollars by doing this maintenance myself.
In summary, the PartSelect person taking my order was knowledgeable and professional, I received my parts two days after ordering, the parts worked perfectly, and the company refunded my two, unopened returned parts promptly. Overall, a terrific experience. I highly recommend them to any capable do-it-yourselfer.
Removed drum replaced pulley attached pulley spring to catch on motor bracket put belt on drum put drum in aligned belt and pulley released. Spring replaced door and top
I have read other postings which describe most of the procedure very well, so I'm just going to add things that should be considered, which I have not read about here. Removing the drum proved difficult due to the lack of room on the two sides.The vent blower motor bracket is at the front bottom of the dryer, and when the two screws
... Read more on either the left or right side are removed, the dryer sides spread more easily and allow the drum to be removed or re-installed more easily. Next, the rear drum bearing I bought has a rubber o-ring which holds it in place. There is a good chance this o-ring will be hard and brittle after years of service, and will crumble when removed, in order to replace the bearing. I had to run to the local hardware store to get a new o-ring, and could only find one that did was not rated for high heat usage. I presumed once the drum is re-installed that the bearing can't dislodge even with a missing o-ring. I think it just holds the bearing in place while removing and re-installing the drum, but I cannot be certain about this.So if you plan to replace the rear drum bearing, make sure to also order the o-ring that holds it in place. It is doubtful you can re-use the old one depending on the age of your dryer. Replacing the old white belt tensioning pulley requires the removal and re-installation of a "nut" that has no threads. It is forced on and off and not simple to re-install. The removal was easy simply by using a wrench to "unscrew" it counterclockwise. But re-installing it is another matter. It requires force to get it back onto the shaft. I saw a tip to use a 7/16" socket placed over the nut and hit with a hammer while bracing the bracket from the other side. I did this by used a smaller tool, linesman's pliers, which provided the force needed. Install it about 1/4" past the end of the bracket shaft. Careful, that nut has sharp edges and I ended up bleeding from that process. Three hands would help: one to brace the bracket, one to hold the nut and socket in place, and one to hammer. So good luck with that. Probably there is a smarter way to do this. If you replace the old white plastic belt tensioning pulley with a new yellow one, it is not simple to understand how to re-install the belt properly. The videos do not do the trick adequately. I did find one on youtube where they removed the dryer side in order to show the belt installation and I had an "aha moment". Since you cannot see the belt, the pulleys, the motor, or anything else during installation, it is not a simple thing to do. Here are my tips: Before re-installing the drum, move the belt tensioning pulley bracket to the right (when facing the dryer front) and you will see a little spot where the bracket will stay to the right when engaged in this spot. Engage the bracket and then proceed to re-install the drum. That way, when you reach under the drum to set the belt properly on the pulleys, you won't have to engage the tensioning bracket without being able to see. Once the belt is in place, carefully remove the bracket from the right holding spot and allow it to move back to the left operating position. I used two hands and don't think I could have done it with one. When the belts are new, they can be naturally twisted and you have to be careful to install the belt with no twist. I had to do it twice to get it right. If someone can take up the top belt slack for you, it's easy to feel the belt underneath the drum and get any twists out. Next, i had a hard time inserting the drum back into the dryer and finding the hole where the bearing inserts. The problem is, if you are not careful, it's easy to move, bend, or break the heater wires which surround the hole you need to locate blindly and slip the drum bearing into. I did bend those wires, but luckily not break them. In hindsight, applying some masking tape to the rear inside panel of the dryer right at the top, left and right of the drum BEFORE removing the drum would have made it much easier estimating the proper drum height while maneuvering the bearing into the rear hole. Then remove the masking tape when done. I ordered a new top plastic front bearing that supports the drum in the front. Good thing I did because mine was split about 5" where one set of the green and white sliders install. I had one white "plastic" insert visible. The other one plus the two green bearings were totally missing. No wonder it was squealing. Finally, the hardest part for me was re-installing the top of the dryer! Take a good look before removing it so you can see exactly how the top fits to the dryer and how the parts need to be lined up first. Thanks to PartSelect.com! Every part was correct and the installation videos gave me so much help. Also, parts arrived in two days, which surprised me. I will be ordering all parts here.
Follow the instructions from YOUTUBE to replace the new drive belt..
Phuc from WOODBRIDGE, VA
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Squeaking
Replace the front and rear bearings. When I have to do it again I will only order (3106), (313), 2x (316) green, 2x (316) white, and drive belt. Taking it apart and putting it back together was easy. Unplug the unit. Take out the 2 philips screws that hold on the top. Lift the top from the front to clear the locking tabs in the back and t
... Read moreake it off. Take out the 2 5/16 screws that hold on the front. Tilt the front (door) forward and rest the drum on the dryer sides, you'll see it. Disconnect the wiring harness for the light and door switch, 2 wires. Lift the front off the bottom retaining clips and place aside. Have someone hold up the drum. Reach under and unhook the drive belt. Pull out the drum assembly. Take off the rear bearing, 3 screws. Clean out the heating element area in the back of the dryer while you have a chance. Replace the bearing assembly. I bought the entire bearing assembly but I could have gotten away with just the sleeve ( 3106), but I didn't know that at the time. Take off and replace the drive belt. Lock the tension arm for the drive belt into the compressed position shelf holder by the motor, push the arm down, you'll see it. Replace the drum and have someone hold it up while you rehook the drive belt and release the tension arm. Now, I would suggest replacing the entire front bearing. If the slides have been bad for a while, the plastic bearing (housing) is probably worn out and cracked. I had to order a front bearing assembly because the new slides wouldn't work with the worn out assembly, no big deal, it came quick. Unscrew the light bulb. Slowly pull the assembly away from the top of the front metal panel, slowly, and pay attention to where everything lines up. Replace the new front bearing and put the new slides on the little plastic tabs, be careful so you don't snap them off. Green on top, white on the sides. Replace the lightbulb. Set the front panel into place on the tabs at the bottom of the dryer. Rehook the door wires (2), and have someone hold up the drum while you slide the front bearing into the drum. Holding the front panel in place, turn the drum by hand and check for binding, things that don't sound or look right. Replace the 2 nuts to hold on the front. Plug it in, keep your hands back, turn it on, look, listen, everything fine. Open door, unplug, replace the top and the 2 screws that hold it on. Plug in, turn it on and check for any noise, you shouldn't hear any. If you do, you didn't do something right or maybe your drive pulleys are bad. A good dad and son job; especially getting on the ground and reaching under to deal with the drive belt. Watch out for sharp edges on the sheet metal and be slow and careful with the front plastic bearing so it doesn't snap. Your now good for 5 more years. A 2 on the difficulty scale, just take it slow and have an extra set of hands.
Follow YouTube "how to change dryer's belt" some video is very clear.
ruoli from Germantown, MD
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
3
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
10 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Monte
January 21, 2023
is motor supposed to stay running after pressing start button with the belt off
For model number GTDP180EDOWW
Hi Monte,
Thank you for your question. The motor will still run, but the drum will not turn. If you need a new belt, the part number listed for it is PS16542496. If you would like to place an order for it, please call our customer service line and anyone will be happy to assist you. We look forward to hearing from you!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Steven
May 22, 2023
I have a very bad squeaking noise happening when dryer is running. I’m assuming it needs a new belt. Could it been anything else?
For model number DPSR483EAOWW
Hello Steven, thank you for getting in touch. Based on our understanding of the issue, we would suggest you replace the drive belt, part number PS16542496, to fix the issue. We hope this helps, good luck with this repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Ariel
July 7, 2023
Im not sure of the model. But the belt is 1/8 in thick and 89 in long it ropp3d so im not sure... but im wondering if the width will fit
For model number GTDP350GMWS
Hello Ariel, thank you for your question! The overall dimensions of the mentioned belt are: 89-1/2"L x 1/4"W x 1/8"H. We hope this is what you were looking for!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Dan
12 days ago
Dryer shuts down while in the drying cycle.
For model number DBXR463GD2WW
Hello Dan, thank you for reaching out. Based on our understanding of the issue, we would suggest replacing the timer, part number PS267977, to solve the problem. It controls the electrical components and the duration of the dryer cycles. Glad to be of help!
How do you if it is the belt? This just stop after turning it on.
Does it need two belts?
For model number GTDP280ED0WW
Hello Jerri, Thank you for your inquiry. Check the belt for any excessive wear and tear and to see if it came off the pulley. The model number that you have provided only uses one belt. The other causes of this issue could be a faulty drive motor, a faulty belt interlock switch, or a faulty door switch. You can test the parts with a multimeter. If you are unfamiliar with how a multimeter functions, we have videos available to assist you. Good luck with your repair.
Do you have a belt compatible with the GE dryer model # DHDSR46GG7WW?
For model number DHDSR46GG7WW
Hello Denise, thank you for contacting us. The compatible belt for your model is the belt drive, part number PS16542496. It attaches to the motor pulley and spins the drum as the motor rotates. Glad to be of assistance!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Dung
March 1, 2023
I need washer belt only
For model number MUD27GESNOWW
Hello Dung, thank you for contacting us. The part you are looking for is the drive belt, part number PS12342956. We hope this helps.
Dryer turns on when pushing button stops when let go of button and drum doesn’t spin
Is that a symptom of a broken belt ?
For model number GTD42EASJ2WW
Hi Steve, thank you for contacting us. We have narrowed the issue down to the following parts: the start button assembly, part number PS11766637, the start switch, part number PS3487190, the felt seal, part number PS12722961, and the drive belt, part number PS16542496. Good luck with the repair!
