Part Location Diagram of WB30X46987 GE Bake Element
See part 290 in the diagram
Replacing your General Electric Range Bake Element
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.com

Bake Element WB30X46987

 Fits your JBS23BC2WH!
★★★★★
★★★★★
91 Reviews

Rated by 36 customers 

Really Easy 

15 - 30 mins 

Ratings submitted by customers like you who bought this part.

$ 120.63
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

 Fits your JBS23BC2WH!
PartSelect Number PS17626202
Manufacturer Part Number WB30X46987
Manufactured by GE for General Electric, Hotpoint, Kenmore
Product Description

Bake Element Specifications

The bake element is located on the bottom of the oven. If your oven will not heat properly it may be due to a faulty or damaged baking element. If you can see that the element has been separated or blistered, you should replace the part immediately. If there is no visible damage, turn the oven on and check to see if the element heats evenly. If the element is not heating evenly, or if it is not heating at all, it will need to be replaced. This element is 19 inches wide x 19 inches long, and has male spade push on terminals.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your General Electric Range Bake Element

Replacing your General Electric Range Bake Element
Troubleshooting
This part fixes the following symptoms:
Little to no heat when baking | Element will not heat | Oven not heating evenly | Will Not Start
This part works with the following products:
Range.
Part# WB30X46987 replaces these:
WB44K10005
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
91 Reviews
4.8
Filter By Rating:
  • 5 Stars
    82
  • 4 Stars
    7
  • 3 Stars
    0
  • 2 Stars
    1
  • 1 Star
    1
Sort by:
  • 1
  • 2
  • 3
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
  • 2
  • 3
Customer Repair Stories
 Average Repair Rating: 4.3 / 5.0, 36 reviews. What's this?
Sort by:
  • 1
  • 2
  • 3
Sorry, we couldn't find any existing installation instruction that matched.
When I took out the baking element, the wires went up inside because they were so short, I got a hold of one of them but couldn't get a hold of the other.
Had to pull out the refrigerator and put it in the dining room in order to pull out the stove to be able to get to the back of it. Had to take off the back of the stove to get to the wiring for the baking element, so at that point I replaced the broil element at the same time. Not a easy job at all.
Other Parts Used:
Bake Element BROIL ELEMENT
  • Daniel from SPRINGFIELD, OR
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Screw drivers, Socket set
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven coil burned out
Removed the hexagon screws. pulled the unit out and wiggled the tabs loose disconnecting them. Installed the new unit-attaching the tabs making sure they were tight. Put the new unit through the opening in the back of the oven and reattached the hexagon screws. Back in business in about 10 minutes.
  • Nancy from RUSH, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven heating element broke
Turn off the power at the breaker. Use hex head bit from 4 in one screwdriver or 1/4 inch nut driver. Heating element comes out, take off wire clamps and install new piece. Put screws back in, turn breaker on and that's it!
  • ryan from NOVATO, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven element broke
Removed bolts unplugged unit then plugged new unit in. Put bolts in and unit works great.
  • Rita from LOCUST, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the old element bunt out.
Followed the video and it was fast and quick.
  • Sandy from PALMER, MA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The element broke in 2....
Pull out wires & replace element by putting wires back in then tighten...done!!!!
  • jannis from PHILLIPSBURG, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lower oven element burned into
Move range out from wall,unplug power supply,remove two screws from back wall of lower oven element unplug two wires,discard burned element.Install new element,plug two wires in,fasten two screws. Done
  • Rickey from Childress, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The lower,BAKE, element had burned in half almost causing a fire.
Slide the rang out to access the 240V plug & unplugging it. Removed the sheetmetal cover from the rear of the range to access the slip on wire plugs to prevent damaging the insulation. The insulation would be damaged if pulling them through the opening in the oven wall with the plugs attached to the element. Removed the racks from the oven. Unscrewed the retaining screws holding the element to the rear wall of the oven, lifted damaged element out and reversed the process for instillation. Perfect opportunity to clean underneath and behind the range.
  • Joseph from DIAMOND SPGS, CA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The bottome heater element of my oven burned out.
I used pliers to remove the hex bolts from the old burner element and pulled out the terminals by hand. I ordered my part and was slightly concerned because the part number was different (this due to my oven being so old I guess). After reading another repair story on this site, when I got my new part, I turned off the electricity to the range at the fuse box vs. unplugging the oven from the wall - because if I had pulled out the oven to access the plug, I would have had to re-caulk along the edges where it connects with my counter tops. I then slid the terminals into the female parts; this was a bit tricky because the female parts had receded behind the insulation in the hole in the back of the oven where they are located. I used small needle-nosed pliers to grab them and pull them forward enough to slide the new terminals in (by hand). I then put in the old hex bolts and used the pliers to tighten them. Flipped the fuse box switch and tried it out - worked great!
  • Mary from ALOHA, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not heat up
I removed the rear lower cover. Disconnected the terminals from the heating element. Removed 2 screws from the heating element from inside the oven. Removed the heating element. Reinstalled everything in reverse order.
  • MICHAEL from MORROW, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
  • 2
  • 3
Questions and Answers

Be the first to ask our experts a question about this part!

You May Also Need ?
Model Cross Reference
This part works with the following models:
PartSelect Number: PS17626202
Manufacturer Part Number: WB30X46987
Brand
Model Number
Description
General Electric
137480
Range
General Electric
137481
Range
General Electric
15451-0
Range
General Electric
154510
Range
General Electric
155910
Range
General Electric
157710
Range
Kenmore
36261101000
Range
Kenmore
36261101001
Range
Kenmore
36261108000
Range
Kenmore
36261108001
Range
Kenmore
36261741000
Range
Kenmore
36261741001
Range
Kenmore
36261742000
Range
Kenmore
36261742001
Range
Kenmore
36261748000
Range
Kenmore
36261748001
Range
Kenmore
36262492000
Range
Kenmore
36262492001
Range
Kenmore
36262780100
Range
Kenmore
36262780101
Range
Kenmore
36262780102
Range
Kenmore
36262780103
Range
Kenmore
36262781000
Range
Kenmore
36262781001
Range
Kenmore
36262781002
Range
Kenmore
36262781003
Range
Kenmore
36262781004
Range
Kenmore
36262788000
Range
Kenmore
36262788001
Range
Kenmore
36262788002
Range
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service