DRYER BEARING SLIDE GREEN 2PK WE03X37317

Light Bulb

Michelle from STATHAM, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers

10 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Gas dryer only fired at the beginning of it's cycle

Be sure to segregate and label all screws.
Remove back and front of control panel.
Removed dryer top.
Removed dryer front/door panel.
Replaced slides. Due to discoloration it was hard to tell the white fr the green. Double checked partselect videos to be sure which was which.
Propped up drum with the dowel to allo ... Read more

Read less

Other Parts Used:

M - Series Secondary Coil - 2 Terminals

M-Series Primary Dual Coil Gas Valve

Robert from RIO RANCHO, NM
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Dryer was making loud noise

Upon receiving the parts, we went to the video repair instructions. We found these videos to be very well done and very helpful. It was great being able to pause the video at specific points until we were able to complete that step of the repair. All of the replacement parts fit correctly and there were no issues.

Other Parts Used:

Stephen from FISHERSVILLE, VA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

6 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

dryer had started making a squeaking noise that got progressively worse with each use

i ordered parts before taking the dryer apart, based on the symptoms others described so that i would have everything i needed. sure enough once i pulled the panels off, the drum slides and entire bearing were destroyed. i assume that happened with age, and ignoring the problem didn't help. by the time i replaced the parts I'm surprised t ... Read more

Read less

Other Parts Used:

timothy from BALTIMORE, MD
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Excessive Drum Noise While Drying Clothes

The PartSelect company's "how to" repair videos are OUTSTANDING. Thank you! The videos provided a comprehensive overview of what to expect in terms of clothes dryer disassembly, component replacement and reassembly. The videos were invaluable tutorials for prior-to-disassembly work.

I ordered all the following parts which I fel ... Read more

Read less

Other Parts Used:

Drive Belt

Rear Drum Bearing Kit

DENNIS from RALEIGH, NC
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Socket set

6 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Loud scrapping sqeaks

Diagnostics, ordered front and back bearing. Added the belt because I was there. Parts came quickly. disassembled, shot photos of wire assemblies. Unprepared for element and lint trap housing failure as the heating element was only 1/2 functional, made followup ordered which included the green and white shims. Note, front bearing replace ... Read more

Read less

Other Parts Used:

Dryer Lint Chute Assembly

Light Bulb

Matthew from AUBURN, WA
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Belt broke

Removed drum replaced pulley attached pulley spring to catch on motor bracket put belt on drum put drum in aligned belt and pulley released. Spring replaced door and top

Other Parts Used:

Drive Belt

Idler Pulley Wheel

Richard from LUMBERTON, TX
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bearings completely worn out, including plastic.

Install would have been easier if part was
an exact
fit. Had to make do with part not fitting exact. Let's just say the dryer works but light won't line up.

Other Parts Used:

Light Bulb

Ruth from GRANITE CITY, IL
Difficulty Level:
Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

7 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Dryer was making a loud noise when running.

I am a 55 year old woman who likes to repair household items. I followed You Tube instructions and did it all by myself. A few screws to get the top off and a two more to remove the front piece. Trap duct assembly was cracked and falling apart. Pulling off the old was fairly easy. I watched the You Tube instructions on my Ipad so I co ... Read more

Read less

Other Parts Used:

Dryer Lint Chute Assembly

Robbin from COLUMBUS, OH
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Loud sqeeking.

I followed some simple instructions from GE. It was really easy and I even found some spare change inside the cabinet which my wife took off my hands. :/

Other Parts Used: