MAIN CONTROL BOARD W/INSTRUCTIONS TL WASHER LE Specifications
This electronic control board is for washers. This electronic control board manages the washer's functions such as filling, washing, draining and spinning.
Ask our experts a question about this part and we'll get back to you as soon as possible!
7 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Terry
June 7, 2023
Machine does not fill all the way. Have blown air through the pressure tubing and it is clear. I do not see a diagram for the fill switch.
For model number GTW465ASN1WW
Hello Terry, thank you for contacting us. According to our research, your model does not come with the water level switch. If the washer is not filling properly, the issue is with the electronic control board, part number PS16874148. It manages the washer's functions, such as filling, washing, draining, and spinning. We hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Mark
April 8, 2023
I can't get the hot water valve to come on . I replaced the selector switch and the water valve. Could it be the control board ? Thank you .
For model number GTW335ASNOWW
Hello Mark, thank you for contacting us. Based on our research, we would recommend checking the electronic control board, part number PS16874148, to fix the issue. Before replacing the board, we would recommend checking whether the hot water valve is completely open or not. You may also need to check whether the pressure of the water is as desired or not. We hope this solves your problem!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Johnny
May 15, 2023
Washer will not spin or drain. Lower drain hose to floor and it emptied the washer so I know it is not clogged. What do I need? Control board?
For model number Gtw46oasj4ww
Hi Johnny, thank you for reaching out. Based on the description that you have provided, we would recommend checking the lid switch assembly, part number PS16554755, as it is the most likely cause of this issue. We hope this information is useful!
Washer periodically stops between cycles and won't run. Usually happens after several loads as if it's overheating. After resting a few hours or overnight, it will run just fine again. Periodically throws a "mode shifter" code, but everything works fine in test mode (until it doesn't, then, drain pump and lock only work but not spin or agitate). I tried replacing a main board but that didn't cure the problem and I've also ordered a mode shifter. Is there anything else that could cause this?
For model number GTW335ASN1WW
Hi J, thank you for asking. Based on our understanding of the issue, we would suggest checking the selector switch assembly, part number PS16217193, to fix the issue. We hope this solves your problem!
Hello, washer comes on, can turn the dial to select setting but does not fill or do anything after that, just makes noises
For model number Gtw460asj0ww
Hello Raymond, thank you for reaching out. We have concluded that the issue is with the water inlet valve, part number PS12726769. You may need to replace the water inlet valve to fix this issue. We hope this is helpful!
will not fill have to keep pushing start pause button
For model number gtw335asnlww
Hello James, thank you for contacting us. Based on our understanding of the issue, we would suggest you check the water inlet valve, part number PS12726768, and the control board, part number PS16874148. We would recommend checking the wire harness to see if it is connected properly or not. We hope this solves your problem!
Just replaced the lid lock because the machine would not spin and drain. that didn't solve the issue. It will not cycle through and I can hear a grinding noise when it hits the spin cycle but will not spin and drain.
For model number GTW460ASJ7WW
Hello Jody, thank you for a very interesting question. We have concluded that the issue is with the drain pump, part number PS12723115. To fix the issue, you need to check the drain pump. We hope this solves your problem!
Ask our experts a question on this part and we'll respond as soon as we can.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Customer Repair Stories
Average Repair Rating: 4.2 / 5.0, 3 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Washer wouldn’t function using any cycle.
First thing is to download and print the programming instructions for the new control board. The instructions for downloading come with the control board. The control board fits multiple models and has to be programmed for your particular model. Unplug the washer and pull it out enough to work from the back. Remove the main control knob by pulling it off. At the top back use the nut driver and remove the 4 screws holding the metal cover. There’s a ground wire attached to the inside of the panel that doesn’t have to be removed. Let the metal cover dangle. Remove the two screws that hold the top control panel. They are located at the ends of the control panel. Slide the main control panel towards the back of the washer above 1/2” and lift it up and roll towards the front of the washer which puts the main control board in a position that allows removal. Unplug all of the connectors. Remove the 3 or 4 screws holding the plastic board stiffener, unsnap the two posts holding it to the control board and remove it. Remove the main control board. Compare the old and new board. If they match install the new board in the reverse order of removal. After reassembly and putting the washer back in place, plug it in and follow the programming instructions. My replacement of the control board went very well except the first new control board didn’t work. There was one complete zone that didn’t function. I called Parts Select and they sent me another control board which worked and the refunded the cost of the defective board but I was out some shipping expense.
Clay from BURNET, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer wouldn't wash rinse or spin
Not knowing for sure how to fit it I went to youtube for help watched a few videos and tested different things until I hit the right one .Moms washer is fixed.replaced lid lock,motherboard and pump I'm sure I don't need all those parts because when I found the code for the lid lock it started working
Cynthia from PACE, FL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
2 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Unit did not go into Spin/Drain cycle.
I thought it was the control board from the onset, but 'Online experts" said it was more likely the mode shifter or the lid lock. I ordered one of each, did not correct problem. Ordered the control board that was designated for this unit, it did not correct problem. Defective? Was send replacememnt, did not fix problem. Twice? Phone conversation with parts person, and after a little digging, it was NOT the correct board, correct board was not available. Returned all parts, refunds all around. Ordered correct board from another site, installed, programed, SUCCESS! Total repair time/installation-less than 15 minutes. Getting the correct part 30 days.
Patrick from GAINES, MI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Socket set
10 of 11 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Customer Reviews
Average Rating:
★★★★★
★★★★★
5 Reviews
3.4
Filter By Rating:
5 Stars
3
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
2
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
PATRICK D - March 17, 2021
Verified Purchase
Great Part, Worked Great
The part is great, PartSelect is great however Fedex took a week to get the part here.
★★★★★
★★★★★
Susan M - September 6, 2020
Verified Purchase
easy repair
part was new and just what we needed. Thank you
★★★★★
★★★★★
Jon Michael G - December 22, 2018
Verified Purchase
Repair shop told me this part was on back order for 4 weeks. Find it on this site in stock and it was $70 cheaper. Can in in 3 days.
In stock $70 cheaper had it in 3 days.
★★★★★
★★★★★
Ross C - August 9, 2018
Verified Purchase
Part did not work. Was faulty part. Had to return it. Cost me extra had to have repair man come ou twice.
Part did not work. Faulty part had to return it. Cos t me extra as I had to have repair man come out twice.
★★★★★
★★★★★
Anna L - April 14, 2018
Verified Purchase
Dead on Arrival
The part was dead on arrival so i can not review the product.
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
PartSelect Number: PS16874148
Manufacturer Part Number: WH22X35597
With the Fix app, you can quickly and easily find information on your appliance, along with videos and articles to help you fix it.
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff
★★★★★
You added 1 item to your cart
✖
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
Your Subscriptions
Same-day Shipping
Ships from USA
1 Year Warranty
365 Day Returns
Copy
