LG/LG_Thumb/138536-1.gif
See part K345 in the diagram

Get in touch, we're here to help!

Open until 10PM EST

customerservice@partselect.com

MOTOR ASSEMBLY,AC,PUMP

★★★★★
★★★★★
2 Reviews
$ 60.76   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS16223509
Manufacturer Part Number EAU61383518
Manufactured by LG
Troubleshooting
This part fixes the following symptoms:
Will not drain | Not draining | Noisy | Leaking
This part works with the following products:
Dishwasher, Washer.
This part works with the following products:
LG, Kenmore.
Part# EAU61383518 replaces these:
4681EA2001S, 4681EA2002D, 4681EA2002H, 4681EA2002K
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Customer Repair Stories
 Average Repair Rating: 3.8 / 5.0, 2 reviews. What's this?
    Sort by:
    Sorry, we couldn't find any existing installation instruction that matched.
    Drain pump needed to be replaced
    Replaced drain pump following easy to follow video. Also replaced circulation pump at same time, as it is connected to common sump housing and only added a few more minutes to repairs.
    • Dean from COMMACK, NY
    • Difficulty Level:
      Very Easy
    • Total Repair Time:
      30 - 60 mins
    • Tools:
      Pliers, Screw drivers, Socket set
    • Parts Used:
      4681EA2001T, EAU61383518
    9 of 10 people found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
    leak from bottom front left.
    Disconnect washer - pull out and turn on it's right side. Remove bottom plate (2 screws). Water intake valve is attached to water line. Disconnect water line. On the other end of the pump is a rubber hose. Disconnect hose by using a pair of pliers to open pipe clamp. Disconnect the electric line by pulling the pronged plug out of the pump. The part is composed of the pump and a metal mounting plate. They are connected by 4 screws. Remove the screws and pull out the back half of the pump. The front of the pump is attached to the washer frame by 2 screws. When removed you will notice an o-ring that forms the seal between the two halves. Remember this when installing the new pump. You will have to take the new pump apart because the whole part will not fit through the frame opening, thus the need to make sure the o-ring is properly seated. You can either install the mounting plate to the frame then attach the pump half or with half of the part in front of the frame and the other half behind the frame connect the two, then attach it to the frame. Reconnect incoming water line using teflon tape and a crescent wrench. Reconnect out-flow line with the pipe clamp and attach the power line. Since you have to take the new pump apart make sure the o-ring is properly seated as it will have a tendency to fall out. Reassemble the rest.
    • Gregory from DENVER, CO
    • Difficulty Level:
      Easy
    • Total Repair Time:
      30 - 60 mins
    • Tools:
      Pliers, Screw drivers, Wrench (Adjustable)
    • Parts Used:
      EAU61383518
    1 person found this instruction helpful.
    Was this instruction helpful to you?
    Thank you for voting!
      Customer Reviews
      Average Rating:
      ★★★★★
      ★★★★★
      2 Reviews
      5.0
      Filter By Rating:
      • 5 Stars
        2
      • 4 Stars
        0
      • 3 Stars
        0
      • 2 Stars
        0
      • 1 Star
        0
        Sort by:
        Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.

          Get in touch, we're here to help!

          Open until 10PM EST

          Contact Customer Service