If your washer shakes or vibrates loudly when it reaches its max speed, check that the leveling legs are even. To ensure that the washer is firmly on the ground using all four legs, adjust the legs so that the machine is level, and tighten the locking nuts on the legs that are threaded. Keep the washer as close to the floor as possible. Your model might have rear legs that level themselves, or it might have threaded legs all around. Make sure the rubber feet have not worn out. Replace any missing or damaged legs and feet. This replacement part is sold individually.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
10 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ken
August 23, 2017
How many leveling feet does a wed6400sw1 have? Two or four?I bought it used and it has no front feet ..i didn't look at the back and i want to order them. is the back feet different?thanks!
For model number whirlpool dryer wed6400sw1
Hi Ken,
Thank you for your inquiry. Your appliance will need 4 legs. I hope this helps. Thank you and have a great day!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Phillip
January 31, 2018
How high are the leveling legs?
For model number WGD7300DW2
Hi Philip,
Thank you for your question. From what I am seeing in the photo we have for this part on our site, this particular leg is approximately 1.5 inches long. I hope that helps. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Nathan
May 7, 2018
Will these feet work with my dryer? I purchased the dryer used and it came with the drawers. I removed the drawer, and it does not have feet on the bottom. How many feet does my dryer need? Thanks.
For model number WED95HEXL1
Hello Nathan, Thank you for contacting us. I have researched the model you have provided and have found the part you’re looking for is PartSelect Number: PS1609293. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Steve
June 5, 2019
If I place this model gas dryer on the level floor next to the washing machine, do I need to have the 4 leveling feet inserted into the gas dryer?
For model number WGD8410SW0
Hi Steve,
Thank you for your question. To make sure the dryer is level, you will need all 4 feet. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Daisy
April 7, 2023
My dryer is missing the leveling feet. Does this part fit my Whirlpool WGD5605MW gas dryer? Thanks!
For model number WGD5605MW
Hi Daisy, thank you for the question. Yes, the leveling foot, part number PS1609293, is compatible with your model. We hope this information is useful!
1 person found this helpful.
Was this helpful?
Thank you for voting!
John
March 8, 2019
How many leveling feet are in a order. One each or four? I also bought my dryer used and did not receive the feet.
For model number AED4370TQ0
Hello John, thank you for your question. The leveling feet are sold individually so there is on in each package. If you did not receive the feet with the new appliance, contact the store it was purchased and speak with them before ordering through us.
Was this helpful?
Thank you for voting!
James
May 6, 2019
If you are using a pedestal under this dryer, do you need the leveling feet?
For model number WED7500GW0
Hi James, thank you for your question. Generally yes. Most of the time what you are supposed to do is screw in the feet as far as they can go so that they are flush with the washing machine. I hope that helps. Good luck with your repair.
Was this helpful?
Thank you for voting!
Mary
May 22, 2023
Is the price for the leveling foot that appears on this site for only one foot or for a set of four?
For model number MGDC300BW1
Hi Mary, Thank you for asking. This replacement part is sold individually. We hope this helps!
Was this helpful?
Thank you for voting!
Kathleen Millett
July 1, 2019
Dryer over heats on all settings. Even when “ no heat” is selected
For model number 110.66972500
Hi Kathleen,
Thank you for your question. If the dryer gets too hot on all settings, there are some parts that you will need to check to see which one is causing the issue. You will need to check the thermal fuse, the internal bias thermostat, the thermal cut-off, the high limit thermostat, the heating element and the heating element connection wire. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
Chris
September 16, 2019
One leg of the dryer appears to be installed using counter clockwise leg. The frame does not look bent at all. Three people looked at it and it looks formed that way - with the thread backwards to the other three. Is one of the legs actually different? Can i order a reverse threaded foot?
For model number YWED4915EW1
Hello, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS11770254 and all appear to be the same thread. They are also sold as a set of 4. Hope this helps!
Average Repair Rating: 4.4 / 5.0, 6 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
No leveling feet on dryer.
This could not have been easier. The hardest part was tipping the dryer over on its' side. Instructions: 1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor. Insert leveling foot into the foot opening on the bottom of the dryer & screw in with fingers until it is difficult to turn. 2. Use the adjustable wrench on the hexed foot (not the threads) to adjust to the desired level. 3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position. 4. Use a level, back to front & side to side, to determine if feet need further adjustment. 5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.
Bobbie from BEND, OR
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench (Adjustable)
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer stopping during dry cycle.
First I pulled the dryer away from the wall and unplugged it. Next I removed the dryer vent hose and threw it away and replaced it with a more rigid metal vent hose. Next, I used a socket wrench to removed the screws holding on the back cover of the dryer. Once the back cover was off it was just a matter of using the socket wrench to removed the bolt holding the sensor in place. After the part was removed I made sure the replacement was orientated in the same way as the original part and then I unplugged the wires from the bad sensor and placed them in the same order on the new part and then I bolted the new sensor back in place. Since the new part has been installed the dryer is working flawlessly and is not turning off mid-cycle like it was. ***Oh, and an important reminder. When you have the back cover pulled off the dryer use a shop vacuum to suck out any dirt and lint in the back of the dryer and make sure you unbolt the metal chute that the dryer lint screen goes into and clean inside the area near the exhaust blower. This is a VERY IMPORTANT part of servicing your dryer and should be done every few months to help avoid the risk of a fire.****
And prior to installing all the parts, Thermal Fuse, Cycling Thermostat, High Limit Thermostat, leveling feet, and I even replace the heating element prior to these parts.
After replacing the heat element as a guess, (which did not fix it), I measured voltage with a DVOM, found lower cut off switch in op, And thanx to some tips on parts select I ordered the the Thermal cut off kit, fast shipping, installed very easily and all is working properly
machine would not agitate properly and NOISY Dryer
took off fabric softener dispenser. used socket to remove agitator. Cleaned and then replaced the little plastic dog ears...works like brand new! It took 15 minutes or less.
Also repaired noisy dryer. replaced drum rollers, pulley and belt. The job took about an hour and was real simple. However..the dryer was still noisy. Fixed with a prybar to force drum to be tighter. It now sounds like brand new.
First removed 8 screws in the back of the dryer to take off the lead 1/4head then removed two blue wires then one screw and you have the thermal fuse . Note: be sure that it is disconected. Before service
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
VINNY C - July 2, 2021
Verified Purchase
correct part
exactly what i need, came within 2 days
★★★★★
★★★★★
Mary Lou H - April 7, 2021
Verified Purchase
Perfect part received
Fits the dryer perfectly. And it came quickly. Thanks
★★★★★
★★★★★
Robert H - January 19, 2021
Verified Purchase
Dryer leveling foot
Part was received quickly and was in good condition
★★★★★
★★★★★
Mike B - December 2, 2020
Verified Purchase
Just what the Appliance Doctor ordered
Part was received in a timely fashion. I will order from this site again should the need arise.
★★★★★
★★★★★
Jerry D - October 6, 2020
Verified Purchase
Fit to a T
Part was exactly what I needed.
★★★★★
★★★★★
Sue C - November 29, 2019
Verified Purchase
Great and speedy service
The part was in great condition and worked perfectly! Great service!
★★★★★
★★★★★
Susan K - October 16, 2019
Verified Purchase
Moved washing machine. Foot broke off in the move
Ordered leveling foot. Came within a couple days. Now able to use machine!
★★★★★
★★★★★
VICENTA E - April 3, 2019
Verified Purchase
Perfect fit
This arrived quickly & was the correct part needed to fix my dryer. Viewing the parts picture made available for review made my purchase easy!
★★★★★
★★★★★
James C - December 24, 2018
Verified Purchase
Easy repair
The leveling feet worked as expected. Only needed a large wrench to adjust once they were started.
★★★★★
★★★★★
Victoria K - August 22, 2018
Verified Purchase
leveling Foot
We truly love these feet they fit our washing machine like a glove. They were so easy to install and when we slid the washer back in place, the feet allowed it to slide so easy. It didn't damage the vinyl like the metal ones did. We recommend these feet.
< Prev
1
2
Next >
Model Cross Reference
This part works with the following models:
PartSelect Number: PS1609293
Manufacturer Part Number: 49621
With the Fix app, you can quickly and easily find information on your appliance, along with videos and articles to help you fix it.
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff
★★★★★
You added 1 item to your cart
✖
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
Your Subscriptions
![](https://partselectcom.azureedge.net/346995-1-S-Whirlpool-341241-Multi-Rib-Belt-92-1-4-amp-quot.jpg "Multi Rib Belt - 92-1/4" – Part Number: 341241")
