Frigidaire/Frigidaire_Thumb/MOHEIM5W.gif
See part F37 in the diagram
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 10PM EST

customerservice@partselect.com

Oven Probe

★★★★★
★★★★★
29 Reviews
$ 32.84   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS1528542
Manufacturer Part Number 316490000
Manufactured by Frigidaire
Product Description

Oven Probe Specifications

This genuine OEM oven probe is also known as an oven temperature sensor or range probe. This part is manufactured for a range, stove, or oven to detect the temperature within the oven cavity. The probe allows the oven to maintain the set temperature by sensing the temperature and sending the information to the ovens motherboard. You may need to replace this part if oven is not heating or is heating unevenly. Be sure to disconnect power to oven before replacing, as it is an electrical part. Tools needed are 1/4 inch nut driver and needle nose pliers.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Oven is too hot | Little to no heat when baking | Oven not heating evenly | Will Not Start
This part works with the following products:
Range, Wall Oven.
This part works with the following products:
Frigidaire, Kenmore, Crosley, Electrolux.
Part# 316490000 replaces these:
AP3963654, 1197392, 316490002, 316490003, 7316490000
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

8 questions answered by our experts.
    Sort by:
    Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
    Delano
    November 24, 2019
    Oven temp won’t go over 250 degrees. It also takes about 30mns to reach that temp.
    For model number LGEF3045KFK
    Hello DeLano, thank you for your question. The most common part that causes that issue is the oven sensor prob PartSelect Number: PS1528542. You can test it with a multi meter. Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. Hope this helps!

    11 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Edward
    November 28, 2019
    Used the self cleaner on the oven, and now it won't come on to bake. Broiler seems to be working. I have seen posts about a thermal fuse. Any help would be great. Thank you. I would like to repair it myself if possible. Not a good day to happen.....thanksgiving day!
    For model number FFEF3017LSG
    Hello Edward, Thank you for the question. I suggest testing the Oven Probe Sensor, PartSelect Number: PS1528542. Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. Hope this helps!

    4 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Rona
    December 24, 2019
    My oven does not heat evenly. I had the oven probe (sku# 31690003) replaced but it did not fix the problem.
    For model number wfe324lw0
    Hi Rona, thank you for your question. There are a few parts that could cause this issue in your appliance. First I would say test your elements with a multi meter to see if they are working correctly or not. They should be reading between 0 - 50 ohms to be working correctly. The other part you should check would be your oven temperature sensor. That can also be tested with a multi meter and should be reading between 1000 - 1100 ohms. If those three parts are fine however, then the issue may be in your control board. I hope that helps. Good luck with your repair.

    3 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Frank
    October 29, 2019
    The oven does not start up, replaced element. Still does not start up. Would it be the temp probe ?
    For model number 79094142312
    Hello Frank, Thank you for the question. It is possible the probe is defective. You can test it with a multi meter. Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. If both elements are not coming on, it is more then likley a defective Electronic Control Board PartSelect Number PS8689401. Hope this helps!

    2 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Related Parts:
    Read
    November 7, 2019
    My oven will not start after cleaning. The igniter comes on and after about 10 seconds it trips the GFCI. I suspect a thermal fuse, but I cannot find one in the parts list.
    For model number LGGF3043KFV
    Hi Read, Thank you for your question. There is no fuse for this model. According to your owner's manual, where your oven is a self cleaning oven, it cleans itself with high temperatures, which eliminates soils in the oven or reduces them to ash that you may wipe away with a damp cloth. The heat from the oven during the self cleaning may have damaged a wire in the oven that may be causing the breaker to trip. You will need to check with a technician to verify what is causing this issue. I hope this helps. Thank you and have a great day!

    2 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Pat
    December 26, 2019
    How do i know if it is an igniter or a sensor? My oven doesn't get hot igniter is orange.
    For model number ffgf3023lwd
    Hello Pat, thank you for your inquiry! We recommend replacing the Oven Bake Igniter if your oven isn't getting hot. If the element shortens out, is no longer glowing, or is only glowing red or orange, replacing the igniter is the solution. I hope this information helps!

    1 person found this helpful.

    Was this helpful?
    Thank you for voting!
    Amanda
    November 23, 2019
    Can a temp. Sensor be going bad and still read good on a meter. Oven seems to lose heat and quit working after preheat. Sometimes u can turn it off and on and it will start back working group right everything going else works fine no codes either
    For model number Ffef3015pwb
    Hi Amanda, the temperature sensor is part PS1528542. Thank you for your question and good luck with your repair!

    Was this helpful?
    Thank you for voting!
    Related Parts:
    Martin
    November 10, 2019
    Surface burners and oven is not working but clock setting is working.
    For model number FEF368GBA
    Hello Martin, thank you for your question. The oven control board is what control the oven. If the oven isn't working at all (bake or broil) the electronic board should be replaced. The surface burners are controlled by the infinite switches. We would recommend testing the switches to determine if they are faulty. I hope this helps.

    Was this helpful?
    Thank you for voting!
      Part Videos

      Replacing your Frigidaire Range Oven Probe

      Customer Repair Stories
       Average Repair Rating: 4.2 / 5.0, 14 reviews. What's this?
      Sort by:
      Sorry, we couldn't find any existing installation instruction that matched.
      oven temp not consistent with setting
      took off back cover and unplugged old unit and installed new unit. oven probe was not the issue. probally control panel malfunction of readings. will continue using oven temperatue gauge inside to get settings for temperture as temp is important for baking.
      • john from spring, TX
      • Difficulty Level:
        Easy
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Nutdriver
      • Parts Used:
        316490000
      62 of 138 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      oven did not heat up
      Replaced the probe because that's what this site recommended.The oven still does not heat up.
      • Tim from ASHAWAY, RI
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Socket set
      • Parts Used:
        316490000
      55 of 64 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      trouble code F10 low oven temperature, oven not overheating,low resistance reading on ohm meter
      Turned off electric,removed rear panel and replaced part.oven is now operating good as new.
      • Michael J from STATEN ISLAND, NY
      • Difficulty Level:
        Very Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Nutdriver, Screw drivers
      • Parts Used:
        316490000
      14 of 16 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Range would start beeping and needed to be unplugged.
      Remove 4 screws on back panel. Unclip wire connector and remove probe and install new probe.
      • George from TURNERSVILLE, NJ
      • Difficulty Level:
        Very Easy
      • Total Repair Time:
        Less than 15 mins
      • Tools:
        Nutdriver
      • Parts Used:
        316490000
      11 of 12 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      oven would not heat up error code F10 showing on veiw screen
      move the range out and unplug power supply, removing the back cover allows access to the probe, this can be done with screw driver or nut driver, loosen clamp that holds power cord in place and move backing out of the way, be careful sheet metal can be sharp, locate the probe unplug the connector and remove screw holding probe, pull old probe out install new probe, fasten down and plug in connector. attach backing and tighten clamp on power cord, plug in to power supply, turn on oven and give it several minutes for probe to work, it took only 20 minutes to replace the bad probe and the oven works like new hop this helps
      • Jess from DEWEY, OK
      • Difficulty Level:
        Very Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Nutdriver, Screw drivers
      • Parts Used:
        316490000
      9 of 10 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      OVEN WOULD NOT HEAT UP OVER 100 DEGREES
      I "You Tubed" disassembly and commenced by disconnecting electric power. Removed door via You Tube instruction, removed back panels of unit, and replaced the oven temp probe. Easy Peasy. Then removed bottom of oven, next level above the burner and started to remove the igniter. One nut refused to be removed so I removed the burner and cut the nut and drilled it out. I reinstalled the new igniter with a metal screw from the rear panel and reinstalled the burner. Through the tiny hatchway I reconnected the new igniter and reassembled the oven to test. Just fine heated to 350 in 7 minutes. Awesome. Then, I called my brother, Pat, to give his imprimatur to the hillbilly nut switch. He said ok, I am done.

      To any reading this, I would order the igniter and the burner at the same time. That tough nut cost my one extra hour.
      • Lawrence from LIVINGSTON, NJ
      • Difficulty Level:
        A Bit Difficult
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Nutdriver, Pliers
      • Parts Used:
        316490000, 316489403
      4 of 4 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      My five-year-old Frigidaire Gas stove was giving an F 10 code.
      I looked up the problem on YouTube and it said it was the oven temperature probe was going out. So I ordered the probe and it was shipped out, received within two days. Took out a few screws on the back of the stove installed it, put it all back together and it’s working perfect.
      • Tracy from Summerville, SC
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Screw drivers
      • Parts Used:
        316490000
      3 of 3 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Oven was over heating. In bake mode broiler would glow red and didn’t cut off after preheat
      Removed 4 screws on back cover removed 1 screw holding probe and unplugged the probe took it out and installed new probe.
      • James from S CHESTERFLD, VA
      • Difficulty Level:
        Very Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Nutdriver
      • Parts Used:
        316490000
      2 of 2 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Oven was not heating up properly
      I followed the video on the website. The probe is on back of the oven. Just unplug part and replace. That was not our fix all though as I later found that the igniter was not working. The igniter is also an easy fix but you access it through the front of the oven. Also an easy swap.

      Oven is working great now.

      Our issues kind of fell between two of the descriptions so I went with high percentage cheaper fix first.

      If your oven is intermittingly getting hot or to temperature of 100, it is probably the igniter.

      Have used PartsSelect for Washing Machine, Dryer, Refridgerator and now the Range. Super easy to figure out needed parts and videos walk you through the repair.

      Thanks
      • Robert from GILROY, CA
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Nutdriver, Screw drivers
      • Parts Used:
        316490000
      1 person found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Range displayed error code F10
      Unplugged range; removed back cover; removed old oven probe. Installed new probe; replaced cover; connected power and turned on range - that simple. My only issue was probe was shipped in bubble rap and unit was slightly damaged (bent). Once straightened, the probe could be installed. Probe should have been shipped in sturdy cardboard cylinder or box. I called customer service, they were very nice, and noted my feedback on my account in case the unit fails prematurely.
      • Timothy from Palm City, FL
      • Difficulty Level:
        Very Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Nutdriver, Screw drivers
      • Parts Used:
        316490000
      1 person found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Customer Reviews
      Average Rating:
      ★★★★★
      ★★★★★
      29 Reviews
      4.7
      Filter By Rating:
      • 5 Stars
        24
      • 4 Stars
        3
      • 3 Stars
        1
      • 2 Stars
        0
      • 1 Star
        1
      Sort by:
      Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
      Model Cross Reference
      This part works with the following models:
      PartSelect Number: PS1528542
      Manufacturer Part Number: 316490000
      Brand
      Model Number
      Description
      Kenmore
      79071342700
      Range
      Kenmore
      79071342701
      Range
      Kenmore
      79071342702
      Range
      Kenmore
      79071342703
      Range
      Kenmore
      79071342704
      Range
      Kenmore
      79071342705
      Range
      Kenmore
      79071342706
      Range
      Kenmore
      79071343700
      Range
      Kenmore
      79071343701
      Range
      Kenmore
      79071343703
      Range
      Kenmore
      79071343704
      Range
      Kenmore
      79071343705
      Range
      Kenmore
      79071343706
      Range
      Kenmore
      79071343707
      Range
      Kenmore
      79071343708
      Range
      Kenmore
      79071343709
      Range
      Kenmore
      79071344700
      Range
      Kenmore
      79071344701
      Range
      Kenmore
      79071349700
      Range
      Kenmore
      79071349701
      Range
      Kenmore
      79071349702
      Range
      Kenmore
      79071349703
      Range
      Kenmore
      79071349704
      Range
      Kenmore
      79071349705
      Range
      Kenmore
      79071349706
      Range
      Kenmore
      79071352700
      Range
      Kenmore
      79071352701
      Range
      Kenmore
      79071352702
      Range
      Kenmore
      79071352703
      Range
      Kenmore
      79071353700
      Range

      Get in touch, we're here to help!

      Open until 10PM EST

      Contact Customer Service