Oven Probe 316490000 | Official Frigidaire Part | Fast Shipping | PartSelect
Oven Probe – Part Number: 316490000
( Grid squares measure 1x1 inch )
Oven Probe – Part Number: 316490000 Oven Probe – Part Number: 316490000 https://partselectcom.azureedge.net/Schematics/Frigidaire/MOHEIM5W.gif

Oven Probe

PartSelect Number PS1528542

Manufacturer Part Number 316490000

Manufactured by Frigidaire

Product Description

Oven Probe Specifications

This genuine OEM oven probe is also known as an oven temperature sensor or range probe. This part is manufactured for a range, stove, or oven to detect the temperature within the oven cavity. The probe allows the oven to maintain the set temperature by sensing the temperature and sending the information to the ovens motherboard. You may need to replace this part if oven is not heating or is heating unevenly. Be sure to disconnect power to oven before replacing, as it is an electrical part. Tools needed are 1/4 inch nut driver and needle nose pliers.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting

This part fixes the following symptoms:

Oven is too hot | Little to no heat when baking | Oven not heating evenly | Will Not Start

This part works with the following products:

Range, Wall Oven.

This part works with the following brands:

Frigidaire, Kenmore, Crosley, Electrolux, Tappan, Kelvinator, Westinghouse, Gibson.

Part # 316490000 replaces these:

1197392, 316490002, 316490003, 7316490000, AP3963654.
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
8 questions answered by our experts.
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Part Videos

Replacing your Frigidaire Range Oven Probe

Customer Repair Stories
Average Repair Rating: 4.2 / 5.0, 14 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
john from spring, TX
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Parts Used:
316490000
oven temp not consistent with setting
took off back cover and unplugged old unit and installed new unit. oven probe was not the issue. probally control panel malfunction of readings. will continue using oven temperatue gauge inside to get settings for temperture as temp is important for baking.
62 of 138 people found this instruction helpful.
Was this instruction helpful to you?
Tim from ASHAWAY, RI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Parts Used:
316490000
oven did not heat up
Replaced the probe because that's what this site recommended.The oven still does not heat up.
55 of 64 people found this instruction helpful.
Was this instruction helpful to you?
Michael J from STATEN ISLAND, NY
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Parts Used:
316490000
trouble code F10 low oven temperature, oven not overheating,low resistance reading on ohm meter
Turned off electric,removed rear panel and replaced part.oven is now operating good as new.
14 of 16 people found this instruction helpful.
Was this instruction helpful to you?
George from TURNERSVILLE, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Parts Used:
316490000
Range would start beeping and needed to be unplugged.
Remove 4 screws on back panel. Unclip wire connector and remove probe and install new probe.
11 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Jess from DEWEY, OK
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Parts Used:
316490000
oven would not heat up error code F10 showing on veiw screen
move the range out and unplug power supply, removing the back cover allows access to the probe, this can be done with screw driver or nut driver, loosen clamp that holds power cord in place and move backing out of the way, be careful sheet metal can be sharp, locate the probe unplug the connector and remove screw holding probe, pull old probe out install new probe, fasten down and plug in connector. attach backing and tighten clamp on power cord, plug in to power supply, turn on oven and give it several minutes for probe to work, it took only 20 minutes to replace the bad probe and the oven works like new hop this helps
9 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Lawrence from LIVINGSTON, NJ
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
Parts Used:
316490000, 316489403
OVEN WOULD NOT HEAT UP OVER 100 DEGREES
I "You Tubed" disassembly and commenced by disconnecting electric power. Removed door via You Tube instruction, removed back panels of unit, and replaced the oven temp probe. Easy Peasy. Then removed bottom of oven, next level above the burner and started to remove the igniter. One nut refused to be removed so I removed the burner and cut the nut and drilled it out. I reinstalled the new igniter with a metal screw from the rear panel and reinstalled the burner. Through the tiny hatchway I reconnected the new igniter and reassembled the oven to test. Just fine heated to 350 in 7 minutes. Awesome. Then, I called my brother, Pat, to give his imprimatur to the hillbilly nut switch. He said ok, I am done.

To any reading this, I would order the igniter and the burner at the same time. That tough nut cost my one extra hour.
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Tracy from Summerville, SC
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Parts Used:
316490000
My five-year-old Frigidaire Gas stove was giving an F 10 code.
I looked up the problem on YouTube and it said it was the oven temperature probe was going out. So I ordered the probe and it was shipped out, received within two days. Took out a few screws on the back of the stove installed it, put it all back together and it’s working perfect.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
James from S CHESTERFLD, VA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Parts Used:
316490000
Oven was over heating. In bake mode broiler would glow red and didn’t cut off after preheat
Removed 4 screws on back cover removed 1 screw holding probe and unplugged the probe took it out and installed new probe.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Robert from GILROY, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Parts Used:
316490000
Oven was not heating up properly
I followed the video on the website. The probe is on back of the oven. Just unplug part and replace. That was not our fix all though as I later found that the igniter was not working. The igniter is also an easy fix but you access it through the front of the oven. Also an easy swap.

Oven is working great now.

Our issues kind of fell between two of the descriptions so I went with high percentage cheaper fix first.

If your oven is intermittingly getting hot or to temperature of 100, it is probably the igniter.

Have used PartsSelect for Washing Machine, Dryer, Refridgerator and now the Range. Super easy to figure out needed parts and videos walk you through the repair.

Thanks
1 person found this instruction helpful.
Was this instruction helpful to you?
Timothy from Palm City, FL
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Parts Used:
316490000
Range displayed error code F10
Unplugged range; removed back cover; removed old oven probe. Installed new probe; replaced cover; connected power and turned on range - that simple. My only issue was probe was shipped in bubble rap and unit was slightly damaged (bent). Once straightened, the probe could be installed. Probe should have been shipped in sturdy cardboard cylinder or box. I called customer service, they were very nice, and noted my feedback on my account in case the unit fails prematurely.
1 person found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
29 Reviews
4.7
out of 5
Filter By Rating:
  • 5 Stars
    24
  • 4 Stars
    3
  • 3 Stars
    1
  • 2 Stars
    0
  • 1 Stars
    1
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Model Cross Reference

This part works with the following models:

PartSelect Number: PS1528542
Manufacturer Part Number: 316490000
Brand
Model Number
Description
Kenmore
79071342700
Range
Kenmore
79071342701
Range
Kenmore
79071342702
Range
Kenmore
79071342703
Range
Kenmore
79071342704
Range
Kenmore
79071342705
Range
Kenmore
79071342706
Range
Kenmore
79071343700
Range
Kenmore
79071343701
Range
Kenmore
79071343703
Range
Kenmore
79071343704
Range
Kenmore
79071343705
Range
Kenmore
79071343706
Range
Kenmore
79071343707
Range
Kenmore
79071343708
Range
Kenmore
79071343709
Range
Kenmore
79071344700
Range
Kenmore
79071344701
Range
Kenmore
79071349700
Range
Kenmore
79071349701
Range
Kenmore
79071349702
Range
Kenmore
79071349703
Range
Kenmore
79071349704
Range
Kenmore
79071349705
Range
Kenmore
79071349706
Range
Kenmore
79071352700
Range
Kenmore
79071352701
Range
Kenmore
79071352702
Range
Kenmore
79071352703
Range
Kenmore
79071353700
Range