Bolt not included. This part connects the transmission drive shaft to the agitator base.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your General Electric Washer Agitator Coupling
Troubleshooting
This part fixes the following symptoms:
Will not agitate
This part works with the following products:
Washer.
This part works with the following products:
General Electric, Hotpoint.
Part# WH43X10032 replaces these:
AP3995059, 1264702
Customer Reviews
Average Rating:
★★★★★
★★★★★
21 Reviews
4.9
Filter By Rating:
5 Stars
19
4 Stars
2
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Thomas M - May 13, 2023
Verified Purchase
Very easy repair!
Coupling arrived earlier than expected, repair took 7 minutes to complete and works as expected. Very pleased ??!
★★★★★
★★★★★
Jason S - November 25, 2021
Verified Purchase
Fixed my non agitating and free spinning agitator
Part was good quality. I popped the cap off agitator and used a 12inch extension to reach 3/8 bolt. Took off agitator and flipped upside down. I then used 4 flathead screwdrivers to depress tabs then turned over and used a long screwdriver to push out old agitator coupling. Flawless. Wiped everything down and then pushed new agitator coupling in place. PERFECT! put everything back together and washer worked better than the first day of use! Thank you PART SELECT!!!
★★★★★
★★★★★
Philip C - November 19, 2019
Verified Purchase
Agitator and Coupling for GE Washing Machine
Shipment was extremely fast. Parts fit and work great and my washing machine is working again. The instructions you provided for installation made the repair easy. Thanks again.
★★★★★
★★★★★
Deborah S - October 23, 2019
Verified Purchase
Just exactly what I ordered
The part came in three days and was easy to put on. My machine works just like new.
★★★★★
★★★★★
Richard W - June 6, 2019
Verified Purchase
Awesome worked as expected
Came in a week later went in easy works great
★★★★★
★★★★★
James S - May 27, 2019
Verified Purchase
Easy repair
Part arrived on time and as discribed. Repair was easily completed.
★★★★★
★★★★★
Anthony D - January 31, 2019
Verified Purchase
Great part
Easy repair and the part came fast
★★★★★
★★★★★
Donald C - November 13, 2018
Verified Purchase
I received my part in 2 days
Was washing clothes in 2 days.
★★★★★
★★★★★
EDWARD K - October 29, 2018
Verified Purchase
AGITATOR COUPLING
Just had to line up the blades with the slots, easier than expected.
★★★★★
★★★★★
Michael J - September 5, 2018
Verified Purchase
Replace worn agitator...
The agitator replacement part from PartSelect fixed the problem with my washing machine, which was not turning both directions. My wife was ready to have a new machine installed for $350-$900. The part was easy to install with the instructions provided on the links from their website. Thanks! for helping me diagnose the problem and save a ton of money!
< Prev
1
2
3
Next >
Customer Repair Stories
Average Repair Rating: 3.9 / 5.0, 17 reviews.
What's this?
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Lower agitator, very loose and wobbly
Reached down into the washer bowl. Fingers on each side of the agitator base. Quick jolt up agitator popped out adjustable wrench took the bolt. Off of the agitator coupling removed coupling wire, brushed the gear slots installed a new coupling with both new bolt lined up, agitator slots pump, the new agitator on after lined up with a dow
... Read moren force quick jolt, then installed the new fabric softener, part on top of agitator
Popped cap off of agitator and used 12inch extension with 3/8 socket to remove bolt. Pulled off agitator and turned upside down. I then used 4 flathead screwdrivers to depress tabs on old coupling and flipped agitator back over and used a long screwdriver to push old coupling out. Flawless! Wiped everything down and pushed new agitator c
... Read moreoupling right in place! Perfect! Put everything back together and washer is back in business!! Thank you PARTSELECT!!
Read less
Jason from BRIMFIELD, MA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Agitator free spins
This was one easy job and saved me money by doing it myself, First I unplugged the washer for safety, then I removed the Agitator by grabbing the base of the agitator with both hands and pulling up I set the agitator a side and removed the one bolt holding the agitator coupling in place. the replacement coupling was a little tight when I
... Read morereplaced it due to it being new, (make sure the coupling is fully seated before installing the bolt) reinstalled the agitator plugged the washer back in and tested repair worked flawlessly thanks partselect
Read less
Darrell from CLARKESVILLE, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set
3 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Inner Tub Base Hub replacement
The tub base hub developed a large crack and spin started to make a large vibration. Agitator coupling was frozen, so I broke it by dremel, wedge (a minus driver) and a hammer. The hub nut was also frozen, so I cut two slits into the nut with dremel, then broke it into two with a wedge and a hammer. Once the hub nut was removed installing
... Read more new parts was straightforward. Half year ago I replaced the timer and capacitor of this washer and together with this repair the total repair cost has now run up to $300. I think I should have bought a new washer half year ago but now that the repair has been done, I hope it will keep working for at least another 5 years. Otherwise I can't justify the $300 cost.
I paid over $100 several years ago to have this same repair done by an appliance repairman. I did it myself this time for less than $20. Definitely watch the installation video before you start. Remove agitator by pulling it up by its bottom flange (protect your face in case it pops off suddenly). Remove bolt holding agitator coupling ont
... Read moreo the transmission shaft. Pull up on old coupling and remove it. Clean grooves on transmission shaft and then install new coupling over the shaft. Reinstall old bolt and the agitator following video instructions on lining up agitator on the coupling. Note: Standard Fedex Smartpost shipping took 6 days to go from Louisville, Kentucky to western North Carolina. If you're in a hurry it's worth it to pay for expedited shipping. Lots of dirty laundry piles up in a week!
Read less
Douglas from ETOWAH, NC
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
3 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer wouldn’t agitate.
Watched a how to video. Pulled the agitator. Determined that the agitator coupling was worn out. Matched the old agitator coupling to new replacement one. Ordered it. Pushed the new agitator coupling onto the fitting. Secured it with the old bolt. Replaced the agitator. Repaired.
Deborah from MARIETTA, SC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
3 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Agitator Coupling Replacement..
Pry the cap off of the top of the agitator, then one 7/16 bolt to remove the agitator (takes around 15" of extensions to reach the bolt and there is a small o-ring under the bolt that you don't want to miss). The hard part is getting the old coupler out of the agitator. Four lock tabs need to be held back while the coupler is pulled
... Read more out. I warmed it all up with a heat gun, pried the tabs back with screw drivers, and pulled the coupler out with a pair of Channel Locks. Kinda like pulling a very big tooth. After that, all was easy. Line the new coupler up with the locator splines in the agitator, knock it in with a rubber mallet. Slide the agitator back on the shaft, run the bolt back in and tighten (don't forget the o-ring), pop the cap back on. Done.
Removed agitator with rope idea. One quick jerk and it came off. Removed coupling. Replaced with new coupling. Reinstalled agitator. Works fine. Note: I could not see anything wrong with the old coupling. It looked brand new with no noticeable wear!! Thanks for your help in recommending the part that most likely would fix the proble
... Read morem.Tom
Read less
Annamarie from FORT LORAMIE, OH
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noisy while spinning
I dissasembled the machine and it took about 30 minutes. Orderd the parts recommended for noisy spinning. Reinstalled the new parts / changed all drum straps. Cleaned the drain drum and spin drum and after complete reassembly the washer is still noisy in agitation and spin cycle. The motor,transmission,counter weight,and drum look ok but
... Read more there is still a reason why the machine is still noisy. Spent 120.00 dollars on parts so far but the drum and motor,transmission and counterweight are very expensive to replace. I am just going to keep using the machine until the washer fails to work anymore. I'm not going to put any more money in the washer. I will just buy a new one. It's not hard to dissasembled and reassemble the washer. I purchased the parts that was recommended to fix the washer but they were not the ones.The new parts did help like the tub seal but the bottom line is that the washer is still noisy. I watched your videos to work on the washer and there were no special instructions on disassembly and reassembly. Like always there must be more than i know to repair this washer. Thanks
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
6 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The agitator would not spin and it was due to a coupling that was worn down to the nubs
Pulled the agitator off by hand. Loosened the screw on top of the coupling and pulled old coupling off by hand. Replaced part with new coupling and socketed it in place. Replaced agitator by-hand by simply pushing it down on top of coupling making sure the plastic teeth aligned.
Ted from CINCINNATI, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
3 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
8 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Riley
March 4, 2018
Is there another reason why the agitator will not function other then the agitating coupling
For model number WDSR2120J8WW
Hi Riley,
Thank you for your question. If the washer is not agitating, there are some other parts that you will need to check to see which ones are causing the issue. You will need to check the belt, the agitator, the inner tub base hub, the tub dampening straps, the transmission and brake assembly and the lid switch. I hope this helps. Thank you and have a great day!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Angela
December 17, 2017
I am ordering: Partselect number ps1482517
Manufacturer part number wh43x10032
Manufactured by GE it does not come with a screw. What size screw do i need to order to complete the installation of the coupling? Thank you, angela
For model number WDSR2080D5WW
Hello Angela, Thank you for your inquiry. The bolt is part# WH02X10237 size 1/4-20 MCH HXW 5/8 S. Good Luck with your repair!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Ronnie
July 21, 2021
Will only fill and drain no agitate or spin but timer advances it seems like it drains for a long time even though its empty
For model number hswp1000m4ww
Hi Ronnie,
Thank you for your question. If your washer will not agitate, there are some parts that you will need to check to see which one is causing the issue. You will need to check the dual action agitator, the agitator coupling, the drive belt and the lid switch. We hope this helps! Good luck with the repair!
Have noticed plastic shavings on clothes after washing
For model number wwse5240go
Hello Tony, Thank you for contacting us. I suggest checking the following two parts: PS11736866 Agitator and PS1155105 Dual Water Inlet Valve. Sometimes these part can build up sediments that leave particles on clothing. Good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jay
May 22, 2019
My Amana washer does agatates but very slowly what could be the problem.
For model number Gtwp2000fww
Hello Jay, thank you for inquiring. For this symptom you will want to replace either the Agitator part PS11736866, the Agitator Coupling part PS1482517, or the 6-Rib Drive Belt part PS1482278. We hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Mayra
December 8, 2019
Hello, My machine not wash and spin. I already change the timer. What could it be?Thanks
For model number WVSR1060G8WW
Hello Mayra, Thank you for the question. If the appliance is not agitating for the wash cycle and not spinning, I suggest checking the V-Style Drive Belt, PartSelect Number PS270803. Hope this helps!
Hello Ron, Thank you for the question. Yes, this is the Agitator Coupling. We hope this helps.
Was this helpful?
Thank you for voting!
David
July 16, 2021
Leaks on agitation cycle, makes funny sound, makes loud noise on spin, and rubber burn smell with large loads.
For model number GTWN4250D0WS
Hello David, Thank you for the question. We suggest replacing the Tub Seal, PartSelect Number PS4704237. The main tub seal is located between the transmission and the outer tub. Its the primary water seal in the outer tub for the transmission-shaft. If your washer is leaking during the fill cycle, or at agitation time, your tub seal may need to be replaced. When the Seal is worn or damaged, it can also cause the appliance to make noise. We hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
