6-Rib Drive Belt WH01X10302 | Official GE Part | Fast Shipping | PartSelect
6-Rib Drive Belt – Part Number: WH01X10302
6-Rib Drive Belt – Part Number: WH01X10302 6-Rib Drive Belt – Part Number: WH01X10302 6-Rib Drive Belt – Part Number: WH01X10302 https://partselectcom.azureedge.net/Schematics/GE/00123865i04.gif

6-Rib Drive Belt

Product Description

6-Rib Drive Belt Specifications

This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting

This part fixes the following symptoms:

Pumps but will not spin | Will not agitate | Noisy | Spins slowly

This part works with the following products:

Washer.

This part works with the following brands:

General Electric, Hotpoint.

Part # WH01X10302 replaces these:

1264395, AP3968432, WH01X10353.
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Part Videos

Replacing your General Electric Washer 6-Rib Drive Belt

Customer Repair Stories
Average Repair Rating: 3.0 / 5.0, 19 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
jon from barry, IL
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Parts Used:
WH01X10302
broken drive belt
To diagnose, first I unhooked the washer: power, water supply, and drain pipe. I then slid the washer out, laying it on its front. With nutdriver, I unscrewed two screws that held the other end of the drain tube and removed it completely. Then, again with the nutdriver removed 4 screws from the back near the legs, two in between the legs in the middle, and approx. 4 to 6 on the bottom. This let me pull the bottom off partially to access the motor area. (I did did not take the bottom completely off, only about 2/3 off and let it bend over, as it was flexible tin) The belt was broken. After receiving the new belt, I positioned it between the pulley and the motor and between the drum and the big pulley. Then I rotated the big pulley, pulling the belt onto it as I rotated. At the same time, as I rotated, I pulled the other end of the belt on to the little pulley. Once it was on, I would put pressure on it as I turned the pulley, to jump the belt to the appropriate grooves on the little pulley. Note: the replacement belt had been modified, so it had one less groove than the pulley. I would have known this if I had read the insert that came with the belt first! Anyway, this was not a problem, only a design change. Also it was important to start the belt on the inside, so if it slipped, you didnt loose your bite. Total diagnostic, repair, and reassembly time: 30 minutes plus or minus. I had read other online forums that said you had to loosen the motor, etc. And I do know some type of a belt installation tool was offered on line, but I got along fine with my installation method. An extra set of hands would have been helpful, but not necessary.
84 of 97 people found this instruction helpful.
Was this instruction helpful to you?
Mike from Meridian, ID
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Parts Used:
WH01X10302
Broken belt.
Used 1" puddy knife to depress spring loaded retainer tabs. Front panel is removed by prying the top of the front panel away from the machine. Lift front panel to release bottom from machine. Set panel aside. New belt is installed by placing it on the drive pulley and then rolling belt onto the motor pulley. Rotate the motor by hand while moving belt so it is properly seated on pulley.
29 of 33 people found this instruction helpful.
Was this instruction helpful to you?
Eric from Bel air, MD
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Parts Used:
WH01X10302
Washer drum would not spin, broken belt
I used a butter knife to pop plastic clips that hold the front panel to the top panel, one clip on each side of front cover. I never thought the new belt was going to fit, it barely fit on the big pulley, much less around the small pulley too. It needs to be stretched a lot to get it on.. but it will fit :)
18 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Travis from Hagaman, NY
Difficulty Level:
Very Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Wrench (Adjustable)
Parts Used:
WH01X10302
belt fits too tightly toget on easily
took two people to get this belt on
17 of 23 people found this instruction helpful.
Was this instruction helpful to you?
Dirk from Anamosa, IA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
Parts Used:
WH01X10302
Broken Drive Belt
Removed bottom washer plate. Placed belt on small, grooved pulley. Started belt on larger pulley. Clamped lock pliers to larger pulley to prevent belt from slipping off. Turned belt onto larger pulley by turning and pressing the belt close to the smaller pulley. Adjusted belt and replaced bottom plate.
15 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Ron from Mount Vernon, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Parts Used:
WH01X10302
Would not agitate or spin dry
After confirming what I thought was the problem and reading other posts it was fairly easy to replace the belt. After taking the bottom cover loose to gain access to the large and small pulley I found out that the belt was very tight to get on as a previous customer had mentioned. I also used visegrips to hold the belt in place on the large pulley while guideing the belt on the small motor pulley with one hand and turning the drum pulley with the other hand. It helped that I had read the other post first. Next time will be a snap.
15 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Robert from HOLLAND, MI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Parts Used:
WH01X10302, WH2X1198, WH2X1197, WH1X2727
Very Noisy In Spin
When disassembling I could not remove the 1 3/4" tub nut with in house tools and had to order the spanner wrench. Almost mandatory unless you have a socket wrench.
12 of 14 people found this instruction helpful.
Was this instruction helpful to you?
howard from LA FAYETTE, GA
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Parts Used:
WH02X10383, WH07X10019, WH01X10302, WH2X1193
Clutch drive wore out and was making a clunking noise during operation.
I removed the front cover and the top cover. Then I unplugged all the,wires and removed the hangers. Then removed tub and drum together out the front. After beating on the tub nut for 2 hours and drenching it in liquid wrench I realized that the,tub nut was not going to release. Yes I was turning it clockwise. I bring out my chisel and hammer. After removing the,center shaft I chisel the,tube inward till I could get to the nut. Then I chisel the,tub nut into 3 pieces. It then appeared why it wasn't coming loose,earlier the powders,had gotten below the nut and had it cemenred on. So those youtube videos,are helpful to an extent.
6 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Wayne from MINNEAPOLIS, MN
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Tools:
Parts Used:
WX05X20641, WH01X10302
Washer makes loud whining noise, intermittently, during spin cycle.
The "service kit belt tool" was difficult to install, but I oonsider it a necessity. We tried installing the belt without the tool, and the belt kept snapping off the motor drive pulley. Using a cable tie to hold the belt to the drum pulley did not work. I used a length of heavy duty duct tape instead, and that worked OK. Unfortunately, the whining noise is still present with the new belt, so a GE service technician visit has been scheduled. Our belt replacement effort has not been totally wasted, unless the washer can't be repaired economically, since the old belt was fraying.
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Walter from IRVING, TX
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Parts Used:
WH38X10017, WH01X10302
Very loud noise during the spin cycle
The first attempt to fix the problem did not turn out so well. I replaced the tub bearing, split ring, tub bearing washer and the hub washer. After reassembly and testing, the loud airplane noise was still present during the spin cycle
Then I ordered and replaced the mode shifter shaft assembly and, since I was going to disassemble again, also ordered a new 6-rib belt. Once reassembled and tested, it was quieter than when it was when brand new, according to my wife.
Parts came in very quickly and the tutorials/youtubes were spot on.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
16 Reviews
4.4
out of 5
Filter By Rating:
  • 5 Stars
    12
  • 4 Stars
    2
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Stars
    2
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Belt Installation Tool
$24.07
PartSelect #: PS10065458
This part is the replacement belt install tool for your dryer. It comes with two round plastic halves of the tool that are held together with an o-ring (also included). To use the tool, position the two halves of the too...
Model Cross Reference

This part works with the following models:

PartSelect Number: PS1482278
Manufacturer Part Number: WH01X10302
Brand
Model Number
Description
General Electric
57431DCWW
General Electric
57441DCWW
Washer
General Electric
57481DCWW
Washer
General Electric
57751H0WW
Washer
General Electric
57751H1WW
General Electric
57751H2WW
General Electric
57751H3WW
Washer
General Electric
58971K0WW
General Electric
58971K2WW
Washer
General Electric
58971K3WW
Washer
General Electric
EJRR4170E6WW
General Electric
EWA4500DCWW
General Electric
EWA5600G0WW
Washer
General Electric
EWA5600G1WW
Washer
General Electric
EWA5600G2WW
Washer
General Electric
EWA5600G3WW
Washer
General Electric
EWA5600K0WW
Washer
General Electric
EWA5600K1WW
Washer
General Electric
EWA5600K2WW
Washer
General Electric
EWA5600K3WW
Washer
General Electric
EWA6500DCWW
General Electric
GBAN2800F0WW
Washer - WASHER
General Electric
GBSR3140H1WW
Washer
General Electric
GBSR3140H2WW
Washer
General Electric
GBSR3140H3WW
Washer
General Electric
GBSR3140H4WW
Washer
General Electric
GBSR3140H5WW
Washer
General Electric
GBSR3140H6WW
Washer
General Electric
GBSR3140H7WW
Washer
General Electric
GBSR3140H8WW
Washer