This is the replacement start push button for your dryer. It is made of gray plastic and is approximately 1 inch in diameter. The push to start button starts the dryer when you press and release it. The main reason you would need to replace it, is if it is cracked, broken, or missing. To replace the push to start button, simply pull it off the shaft, then press the new button into place. This part is sold individually and is an OEM part sourced directly from the manufacturer.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Dryer.
This part works with the following products:
General Electric, Hotpoint.
Part# WE1M659 replaces these:
AP3965177, 1264292
Customer Reviews
Average Rating:
★★★★★
★★★★★
2 Reviews
4.0
Filter By Rating:
5 Stars
1
4 Stars
0
3 Stars
1
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
JOANNE S - June 29, 2018
Verified Purchase
Exactly What I Needed
Part arrived quickly and was the perfect replacement.
★★★★★
★★★★★
Mike S - April 3, 2018
Verified Purchase
not correct
Our washer had a hard plastic button , this was soft so didnt work although it referenced the same model number of our washer
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.1 / 5.0, 4 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
It was a bit difficult because we ordered the wrong parts twice.
Handyman installed the finally correct switch. It was not the starter button. This company was wonderful. Replaced each part without charge and rushed the replacements to us. Can' say enough good things to thank them for their courtesy.
Phyllis from ORLANDO, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The start push button and the timer knob were broken because of low quality parts.
These buttons are easy to fix. Just line them up with the D shaped shaft and push the buttons to get them to go on.
disconnect power plug unscrew 3 screws in back. lean forward remove button disconnect 2 wires in back of switch. put switch connect 2 wires and button. connect 3 screws in the back. ready to start working
Ask our experts a question about this part and we'll get back to you as soon as possible!
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mary
May 31, 2019
What holds the start button on the back of the panel sometimes does not respond to pushing. If I play with it it sometimes starts. I think its the clip that holds the push button that is not working. What should I buy? Thanks.
For model number GTDP400EM1WS
Hello Mary, Thank you for the question. This could be an issue with the Start Button, PartSelect Number PS3487190 or the mount on the back of the Backsplash, PartSelect Number PS3487096. I suggest opening up the panel to check for any damaged parts. Hope this helps!
Dryer stopped working. Repair person replaced the belt and starter/timer knob. After replacing he had trouble starting dryer. Keep moving starter around and it finally started. Today attempting to dry clothes that I set as
“Cottons more dry”. Dryer has stopped with knob pointed to optimum dry but clothes still wet. This happened 2x. Still trying to dry clothes.
Will not dry or start on permanent press. Off doesn’t work.
For model number GTDP490GD4WS
Hello Gail, thank you for your inquiry. Since you have replaced the knobs, we are suggesting to replace the switch the knob goes on. The Push to Start Switch is PS3487190 and the Timer Switch is PS3654187. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.
Hi Shamas, thank you for reaching out. Confirm the door is fully closed; the dryer will not start with the door open. Remove anything that is obstructing the door. If there is no obstruction, we would recommend checking the door switch, part number PS2344321. Thank you for the inquiry, good luck with the repair!
Hello Judy, thank you for your question. Yes, this is the replacement for your model.
Was this helpful?
Thank you for voting!
Morris
November 20, 2019
Dryer was working fine. Tried to turn it on next day. Pressed start button and all it does is hum. Drum turns but not to easy. Any ideas?
For model number GHDP490EFWW
Hi Morris, thank you for your question. Looking at your model information there are a few parts that you should take out and test to see which one is giving you the issue. The first parts to check in this case would be all of your thermostats and thermal fuses. You can test those parts with a multi meter and they should be reading 0 ohms to be working correctly. If those parts are fine, you should then go on to testing your heating element as well. You can also test that with a multi meter and it should be reading between 0 - 50 ohms. Something else you should also check would be your filter and ducts. Make sure there is absolutely no blockage that would restrict air flow in your appliance. If all of those parts are fine, I would suggest checking your start switch and then perhaps your timer itself. I hope that helps. Good luck with your repair.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
