Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Introducing the Water Inlet Valve from the trusted brand, GE. This essential component facilitates the accurate and efficient flow of water into your washer, enhancing its overall performance. It's crucial you unplug your washer and turn off the water supply before installing this structure, ensuring safety is maintained throughout. Always remember to shield your hands with work gloves during install. Opting for a genuine GE product means committing to high-quality, extended durability and ultimately, peace of mind. Keep your washer operating at its best with this necessary, trustworthy water inlet valve from GE.
Average Repair Rating: 3.3 / 5.0, 2 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Low H20 alert & loud screeching noise when filling
I'd recommend a second set of hand for the repair. First we unplugged the washer. We removed the top panel of the washer using a Phillips head screwdriver. We disconnected all hoses. Then un-screwed the existing valve from the back of the machine and removed all clamps and hoses from the old valve. We then reversed the process for the
... Read more valve install (attached hoses, attached to the machine, etc.) We then ran a test cycle to check for leaks. We then closed everything up and our alert and noise went away.
Read less
Kevin from LOUISVILLE, KY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable)
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Squealing Water Valve When Water Is Filling Washer Tub
Sediment in your water will ruin these water inlet valves over time. It will reduce the amount of water filling the tub & will be very noisy making a squealing sound.
You’ll need a #2 Philips screwdriver & a standard set of pliers.
UNPLUG ELECTRIC SUPPLY FROM WASHER, TURN OFF WATER VALVES, THEN DISCONNECT WATER LIN
... Read moreES & DRAIN HOSE. Pullout the detergent dispenser drawer. Remove 2 self-tapping screws and & 3 sheet metal screws. Slide front control panel to the right and let it rest on the machine. Remove 3 sheet metal screws to release the top lid cover. Pull the lid towards you and lift off. You’ll see water inlet valves in the left rear. Remove Philips head screws securing water inlet valve. Disconnect electrical wires from the water inlet valve solenoids. Using pliers, squeeze hose clamps and slide down small hoses. Pull off or twist the small hoses from the old water inlet valve. Install the small hoses onto the new Walter inlet valve and reconnect electrical harness to water inlet valve solenoids. Mount new water inlet valve, reconnect water supply hoses & turn on water supply. Check for any leaks before going any further. If no leaks, reinstall top lid & front panel. CONTROL PANEL IS DIFFICULT TO LINE UP WHEN SLIDING IT TO THE LEFT TO REINSTALL. LINE UP THE SLOTS FOR THE SCREWS WHEN REINSTALLING THE CONTROL PANEL. Refasten all screws and slide dispenser drawer back into dispenser pocket. Reconnect electrical supply. Washer should operate normally.
Read less
Patrick from GLEN ALLEN, VA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
10 of 10 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Laura
September 30, 2021
Does this part have to be installed by a plumber or other techinicial?
For model number GFW148SSMWW
Hello Laura, thank you for your question. This is a repair you can do yourself. First unplug the washer and turn off both the hot and cold water. Remove the hoses from the washer. Remove the top panel of the washer. Locate the hoses attached to the water valve and squeeze the hose clamps together with pliers to remove. If the hoses are on tight you may have to twist them to break the suction and pry or push them a little with a flat head screwdriver. Once it budges you can take them off with needle nose pliers. Attach the hoses and hose clamps to the new valve. Remove the wire harness from the old valve. You can push it loose with a flathead screwdriver. Take a picture of where the wires go before removing them. Be sure to connect them in the same place on the new valve. If they're hard to get off you can pry them off with pliers by the connectors. Do not pull the wires. Remove the mounting screws holding the valve on and remove the valve. Put the new valve into the holes and replace the screws. Reconnect the wires and replace the top panel. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Anthony
January 12, 2025
My washer is leaving a lot of softener and water in the softener tray.
For model number GFW850SPN1RS
Hi Anthony, thank you for the question. We would suggest checking the dispenser drawer for any clogging first. If the issue persists, you may need to replace the dispenser drawer, part number PS12743649. We hope this sorts out your problem!
Washer
- Ge® Energy Star® 5.0 Cu. Ft. Capacity Smart Front Load Steam Washer With Smartdispense™ Ultrafresh Vent System With Odorblock™ And Sanitize + Allergen
