EVAPORATOR FAN BLADE

1) Unplugged fridge and removed cover over light in freezer.
2)Removed screws holding cover over motor.
3) Removed screws on bracket holding motor in place.
4) Un plugged motor and used razor blade to cut grommet holding wires in place.
5) Plugged in new motor and routed wires through grommet. Then used zip ties to hold grommet together.
5) Re-attached motor bracket and installed new fan.
6) Reinstalled cover over motor.

I replaced all of the plastic parts as well as the heat coil that is mounted at the bottom of the coils that keeps the coils from freezing up. If I had not melted the plastic parts the coil could have been replaced in 2 days, 1 day to receive the part and the next to do the work. This is the second time I have had to replace this heater.

I should state first that I am a DIYer and have no experience fixing appliances. The fan noise seems to be a common problem. It has something to do with the bearings. Mine was actually hitting the housing in front on the fan as well. Getting into the installation, I knew I had to take the back panel and fan housing off. But I found out that everything needs to come off. This is the ice maker, the housing underneath the ice maker as well as the fan housing and back panel. This isn't difficult but good to know before hand. A quick note, the light bulb housings come out by pulling them forward. It's a good idea to label the screws as you take them out as there are quite a few that need to come out. I replaced the evaporator fan the fan blade and one grommet. In hind sight I should have replaced both grommets as they both showed wear. They are both exactly the same so you can order two of the above. All in all this is a pretty easy fix. It takes a bit of time, but it's not to difficult. Th most difficult thing was the wiring. The fan comes with a six prong connector and has four prongs taken up. There is, what I think is a temperature sensor, that takes up the other two prongs. Since I didn't order that part, I had to cut it out of the old connector and insert it into the new evaporator fan connector. This was a bit difficult and would have been much easier if I had ordered the part. Unfortunately, I don't know what that part is called, but it must be some kind of temperature sensor as it clips on the coil. The wires also run through a blue rubber wire-run that needs to be sliced open. This was pretty easy to do with a small serrated pocket knife. SLice it on the back side of it and pull the old wires out. When you are ready to install, just run the new wires through the hole from the old wires. Once you have replaced the fan the new blade and the two new grommets, it's just a matter of replacing all the equipment. Fan housing first, then the upper housing followed by the ice maker and the back panel. Good luck

Firt Removed the Ice Maker Tray and the full ice maker assembly. Removed the plastic shroud that sits over the fan assembly. Since the original connector (or the plug)for the motor had also a temperature sensor attached to it and did not know how to remove and trabsfer to the new motor connector I spliced the new motor to the old connector. It was fairly straight forward. Overall the job was not that difficult and since I was trying to be more meticulous it took a little longer. An average person can do it in around 30 to 45 minutes.

First I removed the shelf and light cover, then removed 3 screws from the ice make. Then I removed 6 screws from the moter cover (back wall of the freezer) and removed it. I then removed the 2 screw holding the moter. This is where the soldering iron comes in. The wire leads from the old motor were molded into a 3" rubber holder and the end wire plastic connector held 6 prongs (2 from a thermo tube). The new motor only held the 4 moter prongs, 2 were empty. To resolve this problem I cut the wires on both the new and old motor. I then attached the old connector to the new moter with the soldering iron and shrink tubing. Replaced all the parts I had removed and started it up. Works like a champ.....

My GE refrigerator emitted high pitch noise a short while ago. I tried different dampening methods that helped but not eliminating the problem. I finally replaced the fan, motor, and associated parts and solved the problem. The total cost was about $50.

i removed srews from area until i could access the fan unit and removed it. wires were not identical so i had to splice some together, most likely could not have been avoided. the exploded parts diagram helped me to be sure that i would have all replacement parts on hand so i wouldn't have to wait for something i had forgotten.

Removed the parts and replaced them with the parts you sent me. Now it operates normally.

The repair did not go exactly the way it was described in the YouTube video, but basically it was similar. After unplugging the power cord, emptying the freezer, removing the shelves and the ice reservoir, I removed the ice maker assembly by unscrewing a Philips head screw and unplugging the power connector. The connector had little retaining tabs on each side that I pried open with a straight blade screwdriver. Then the ice maker lifted right out. Next I removed one screw holding the auger motor assembly, unplugged the power connector, and lifted out the assembly. This where things got difficult. After flailing around a bit, I removed the panel on the back wall of the freezer below the evaporator fan assembly, exposing the evaporator coil. I saw that the fan assembly was attached with two screws at the top and two screws at the bottom. The top screws were easily removed, but when I removed the bottom screws, which were situated in very tight quarters, I DROPPED BOTH SCREWS DOWN BEHIND THE EVAPORATOR COIL. Be prepared with a magnetic nutdriver so this doesn't happen to you. I could not retrieve the lost screws, but fortunately it appears that the top screws hold the assembly securely enough. The assembly was loose, but it was still attached by a power cord that I could not disconnect. I removed the tracks on the side walls for the ice bucket, and then I could maneuver the fan motor assembly just enough that I could reach over the top of it, grab and pull off the old fan blade, and slide the new fan blade onto the shaft. Reassembly was straightforward, replacing each part (except two lost screws) in reverse order to disassembly. After getting everything put back in and plugging in the power cord, I was amazed at how quiet it ran.

Took cover off, pushed blade on, and replaced cover