GE SERVICE MACHINE CONTROL WD21X24901C
★★★★★
★★★★★
Rated by 10 customers
Really Easy
30 - 60 mins
Ratings submitted by customers like you who bought this part.
$
220.98
In Stock
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
PartSelect Number PS17137050
Manufacturer Part Number WD21X24901C
Manufactured by
GE
Troubleshooting
This part fixes the following symptoms:
Will Not Start
This part works with the following products:
Dishwasher.
This part works with the following products:
General Electric.
Part# WD21X24901C replaces these:
WD21X22949, WD21X23712, WD21X24118, WD21X24799, WD21X24901
Customer Reviews
Average Rating:
26 Reviews
★★★★★
★★★★★
4.7
Filter By Rating:
-
5 Stars
-
4 Stars
-
3 Stars
-
2 Stars
-
1 Star
Sort by:
- < Prev
- 1
- 2
- 3
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Rodney F - July 7, 2023
Verified Purchase
Fixed a no start fault
Replaced the pc board. Careful! You'll slice a finger on the stamped metal housing like I did. After I stopped the bleeding the new board went in. After reassembly, the first test run was a success! Dishwasher has been working flawlessly since.
★★★★★
★★★★★
Timothy C - May 6, 2023
Verified Purchase
Easy install
Part worked great, dishwasher works again!
★★★★★
★★★★★
Mark L - January 7, 2023
Verified Purchase
Quick delivery, right part
The control board is a little awkward to install but PartsSelect did everything right & it’s been working right for more than a month.
★★★★★
★★★★★
Roy G - September 17, 2022
Verified Purchase
Patrs Select review
Part works great
★★★★★
★★★★★
Thomas M - September 3, 2022
Verified Purchase
Replacement part fixed the problem
Had a power issue with my 3 year old dishwasher. Found a helpful video and the exact part needed to repair the issue in about 30 minutes. Has worked great for the past 2 weeks. So much better than hiring someone or replacing with a new unit.
★★★★★
★★★★★
Camren S - September 3, 2022
Verified Purchase
Worked as it Should
Part came packaged really well. Was able to easily install. And now the dishwasher works as it should.
★★★★★
★★★★★
David G - August 30, 2022
Verified Purchase
Dishwasher control board
After installation the part took about one hour to ‘wake up’. It worked fine for about two weeks then died! I don’t really blame the part because it was not an exact match but “close and will probably work”! This was the second one to fail, now replacing the dishwasher (5 years old). Buyer beware!
★★★★★
★★★★★
Raymond W - August 26, 2022
Verified Purchase
Part worked as expected no problems.
Part arrived on time quoted.no problems with replacement.directions were great!
★★★★★
★★★★★
JOHN T - May 24, 2022
Verified Purchase
Control board
Works like a champ
★★★★★
★★★★★
Alan H - May 17, 2022
Verified Purchase
part looked good
part did not fix
dishwasher wasted time and money junked washer 3 years old
- < Prev
- 1
- 2
- 3
- Next >
Back to Top
Customer Repair Stories
Average Repair Rating: 3.6 / 5.0, 10 reviews.
What's this?
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
No lights at control panel and no start
Downloaded the GE manual from the internet. Followed the GE repair manual trouble shooting guide. The manual contains all of the disassembly and reassembly instructions. Main board had a more than one volt higher than listed voltage output. Manual does not list an acceptable voltage range so I ordered a new main board. New board had the
... Read more
same output and did not fix the problem. I ordered a new UI board. The new board is a genuine GE "programable" replacement board that covers multiple models.
I set the indicated jumper to the required position for my application and installed it. The problem was not corrected. I read that some people had problems with defective replacement boards so I contacted PartSelect to return the first two boards and reordered the UI board.
I once again set the jumper and installed the UI board and it worked immediately.
The whole repair was extremely easy. PartSelect is very good to work with. I had no problems with returns or refunds. I will definitely use them again if I have the need for any of their products. There were slightly cheaper suppliers, but PartSelect had the parts I needed in stock and they shipped my order lightning fast. They are more than worth the few extra pennies difference.
I set the indicated jumper to the required position for my application and installed it. The problem was not corrected. I read that some people had problems with defective replacement boards so I contacted PartSelect to return the first two boards and reordered the UI board.
I once again set the jumper and installed the UI board and it worked immediately.
The whole repair was extremely easy. PartSelect is very good to work with. I had no problems with returns or refunds. I will definitely use them again if I have the need for any of their products. There were slightly cheaper suppliers, but PartSelect had the parts I needed in stock and they shipped my order lightning fast. They are more than worth the few extra pennies difference.
Read less
-
Robert from Perrysburg, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher seemed dead even though it was getting power
I watched a YouTube video that showed how to to do this. The first trick is finding the right video. This one worked best for me / my model.
https://www.youtube.com/watch?v=sesf0BS8fzM
The first few I watched were for models with the user display on the top of the door, and you have to open the dishwasher to see it ... Read more . Mine shows the display on the outside. Look for the video that has a round plastic "vent" on the inside of the door. You will have to loosen it with some sort of tool in order to remove the display once you get the door taken apart. In the video, they used needle-nose pliers opened wide. My NN pliers don't open that wide, so I used two screw drivers. Pealing off the display is a bit challenging. I was afraid I was going to break the little plastic pins that hold it on. The rest is not too hard though, and it went back together quite easily, even though I did break a plastic piece that 0ne of the UI Control Board screws goes into. Oh well, now it has three screws holding it instead of four.
https://www.youtube.com/watch?v=sesf0BS8fzM
The first few I watched were for models with the user display on the top of the door, and you have to open the dishwasher to see it ... Read more . Mine shows the display on the outside. Look for the video that has a round plastic "vent" on the inside of the door. You will have to loosen it with some sort of tool in order to remove the display once you get the door taken apart. In the video, they used needle-nose pliers opened wide. My NN pliers don't open that wide, so I used two screw drivers. Pealing off the display is a bit challenging. I was afraid I was going to break the little plastic pins that hold it on. The rest is not too hard though, and it went back together quite easily, even though I did break a plastic piece that 0ne of the UI Control Board screws goes into. Oh well, now it has three screws holding it instead of four.
Read less
-
Pete from TRUCKEE, CA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
First time repair. Limited room to maneuver Lower Electronic Control Board.
Accessed YouTube video specific to my Model and replacement part.
https://youtu.be/TI8cUjy5YOE?si=3b0Dkk16WLl2e33D
As outlined above, the replacement took a first timer about 60 minutes to complete and resolved the issue.
https://youtu.be/TI8cUjy5YOE?si=3b0Dkk16WLl2e33D
As outlined above, the replacement took a first timer about 60 minutes to complete and resolved the issue.
-
Walter from MIDDLEBURG, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
It didn’t work I had to wash dish’s by hand
The repair went very well, I watched a video on how to fix it on utube for this model the board from partselect was a OEM and fit perfectly. If I ever have an appliance problem partselct will be the number 1 on my list to call. I have told most of my friends about them and how great they are to deal with. They rate eleven stars.
-
Kathy from ELK, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Turn the dishwasher on and push start, close door and it would beep 3 times and not start.
Well, I was about to go buy a new dishwasher but my wife convinced me to fix it. Ordered the part from PartSelect and I wasn’t sure of the part number but they knew exactly what I needed. The control board. Received the part quickly. Took about 30 minutes. The hardest part was finding the correct socket for the bolt in my tool chest. Supe
... Read more
r easy! Thank you!
Read less
-
Chris from WADDELL, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher would not start. No lights on select board
After reading the manual that came with my dishwasher, 5 years ago, it states if the green LED is on steady, change the machine control board. PartsSelect sent the bd within a week. I replace the board but the result was the same (steady green LED); Contacting PartsSelect, they gave me a return label and shipped another control board. Unf
... Read more
ortunately the second control board had the same outcome. PartsSelect send another return label and I returned both machine control boards. I contacted GE and am having a service man (from GE) come and fix it. The manual for this dishwasher must be in error!! PartsSelect has been fantastic in understanding this and allowing me to return the bds.
Read less
-
RICHARD from NAPLES, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
When we closed the door, it would only beep 3 times, over and over
I watched the video on how to replace the parts and it was very easy. Unplug the power cord, remove the kick plate and insulation. Remove the small square metal cover, remove the 2 screws that hold the control board plate. Unplug the wires, put the control board plate on the counter and replace the board. Then put everything back in the o
... Read more
rder that you removed it. Plug in the power cord. Very easy to fix. I ordered the door latch but didn't need it so I will just keep it as a spare. It took me less than 45 minutes to replace the part. The problem was the control board. Parts select saved me about 400.00. Thanks, John.
Read less
Other Parts Used:
-
john from ALBUQUERQUE, NM
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
7 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Need New Board
Replaced old One,Watched a Clap on You Tub !!!
-
Lauran from MYRTLE CREEK, OR
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers, Socket set
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher would not power up
This dishwasher started to not want to start about 1 year ago but on several attempts to start the dishwasher it would power up or start. On Christmas Eve 2021 I did a load of dishes and from that point on the dishwasher would not power up. Got on line and did some troubleshooting and felt the Control Panel was the problem. Ordered the
... Read more
replacement part from this website, the part arrived around January 1, 2022. Installed the new Control Panel yesterday and my dishwasher is now working great again. Thank you for the ability or order and fix my dishwasher
Read less
-
Rhonda from College Corner, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench (Adjustable)
5 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No power/response at the control panel. Replaced power board first, did not solve the issue. Replaced the control board and works perfectly now.
Followed directions available on YouTube and the written instructions that came with the part. I made the repair more complicated than necessary as I did not notice that the jumpers come attached only to ONE pin out of the box. I took two tries to get the jumper settings right.
-
Jerry from SIMI VALLEY, CA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
9 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Back to Top
Questions and Answers
Be the first to ask our experts a question about this part!
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Back to Top
GE SERVICE MACHINE CONTROL
$
220.98
In Stock
✖
Stock Status
In Stock
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.