Part Location Diagram of WB26X31060 GE FAN BLOWER
See part 32 in the diagram
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Open until 12am EST

customerservice@partselect.com

FAN BLOWER WB26X31060

★★★★★
★★★★★
16 Reviews

Rated by 10 customers 

Easy 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.

$ 82.81
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS12702967
Manufacturer Part Number WB26X31060
Manufactured by GE
Troubleshooting
This part fixes the following symptoms:
Will Not Start
This part works with the following products:
Wall Oven, Range, Microwave Oven Combo.
This part works with the following products:
General Electric.
Part# WB26X31060 replaces these:
WB26X23477, WB26X24020
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
16 Reviews
4.1
Filter By Rating:
  • 5 Stars
    10
  • 4 Stars
    2
  • 3 Stars
    2
  • 2 Stars
    0
  • 1 Star
    2
Sort by:
  • 1
  • 2
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
  • 2
Customer Repair Stories
 Average Repair Rating: 3.0 / 5.0, 10 reviews. What's this?
Sort by:
  • 1
Sorry, we couldn't find any existing installation instruction that matched.
Code F97 GE Monogram Dbl oven
My oven continued showing code F97 when we tried to use it. It would clear sometimes in a minute or 10 min. After some research, I figured it had something to do with the upper and lower cooling fans or the associated circuit boards. These fans send a signal (2.5volts I think) back to the main board identifying they are running correctly (fast enough). If the fans fail to get to required speed, CODE F97 appears. So, purchased both upper and lower fan units along with the corresponding circuit boards and decided to get it a shot. For a $8K oven, I had to try something.

You have to replace the items from the rear. Oven is 360+ lbs., So I purchased a lift from Harbor Freight to support the oven when I pulled it out. Once on the lift and the rear exposed, job was fairly easy.

Just remove the top and rear upper and lower panels, access the fans (circuit boards are attached to the fan housings) and replace with new. 1 hour tops for the entire job. My fans were working, but grease and dust had accumulated on the fins which I fell was my problem. Also, spinning them by hand compared to the new fans showed some drag on the old fans. It could have been a faulty circuit board, but I think it was the fans. The lift is a game changer and really makes this job not too bad.

It's been a week since repair, no F97!!! Ovens works great again!!
Other Parts Used:
COOLING FAN LOWER BOARD SENSOR FAN BLOWER
  • Kenneth from PORT ARTHUR, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Wrench (Adjustable)
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
F96 error code
Removed oven from kitchen cabinet. Used a mover's dolly and made a wooden box from 2x10 boards to set unit on after removal. This allowed me to not disconnect the wiring from inside the cabinet. Off course, the power was off at the breaker box. Started removing oven panel pieces/covers from the top and replaced the lower fan first. Was a little tricky disconnecting the power clip. Replaced the blower, there is no ground wire as the blower is all metal and is attached to a plate that is metal and would be grounded to the unit itself. Went ahead and replaced the top blower as the unit was removed from the wall cabinet and the fan was exposed, why not, it was only $79. Top fan does have a ground wire. Turned the power on and tested unit, worked with no error code.

Replaced all of the covers. One note. I would suggest taking a couple of photos during the removal. I did not, and one piece seemed out of place, but I did figure out where it went on the unit. Saved $$$ doing it myself. Wish I had recorded for a You Tube video. Also, remember to remove and reuse the board sensor if you didn't buy a new one.
Other Parts Used:
COOLING FAN LOWER FAN BLOWER
  • scott from ACWORTH, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
F96 fault code
taking the oven out of the wall the most difficult part.. once you removing the sheet metal screws....be sure to take pictures as you dis-assemble putting back together will be easier. wait for correct part. second try they sent the correct part. put back together, test before putting back into wall.. big savings by doing it yourself.
  • Frank from METHUEN, MA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Error code F96
Very straight forward repair except for removal of the fan mount plate. There are 4 sheet metal screws, 2 of which are obvious and shown in the appliance diagrams, and 2 of which are neither on the appliance diagram nor obvious. These screws are beneath the motor assembly and oriented with the heads between the mounting plate and the top of the oven - about a 3/8 inch gap. Removal was accomplished using a 1/4 inch open end wrench strictly by feel as there is no sight line. Not all that challenging, but still a pain. On reassembly, these screws were reversed so that the head is now on the top of the plate and more accessible.
Other Parts Used:
FAN BLOWER BOARD FAN SENSOR
  • john from ASHEVILLE, NC
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
F96 Code. Oven fan blower defective
TERRIBLE!!!!!!!
FIrst part arrived broken
Second part arrived broken
Third part arrived broken
Finally on the 4th try, the part arrived and was not broken.
I will NEVER again order parts from this company.
  • Gary from GOLIAD, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Blower Fan quit working
It took a while to remove approx 30 screws to get to the blower. So my oven was sitting, torn apart while I waited on the new blower fan that I had ordered. It arrived shortly, about 5 days. When I opened the box I saw that PARTSELECT had sent me a drain pump instead of the blower fan that I had ordered. Since an oven does not require a drain pump and it wouldn't work to replace my broken blower fan I had to return it. I was told that I needed to send the part back in order to get a refund. After I sent their drain pump back at a cost of $13 they emailed me and said I didn't need to send the drain pump back. And they refunded me minus shipping So I had to pay shipping both ways for a part that was wrong. And I ordered it from someone else. I put the new blower fan that I had bought from another company in and replaced the 30 screws. And the oven has been working fine ever since. Thank you PARTSELECT for allowing me to tell people how you operate. They have a money back guarantee, but they don't give you back ALL your money. Thanks Again.
  • Thomas from Goshen, IN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Socket set
12 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
F96 error
Step 1, turn off circuit breaker, verify no power at the back of oven

Step 2, remove oven from wall/housing by removing 4 mounting screws, 2 on each side, just on the inside after opening the oven door...this was the most difficult part doing the repair on my own as the oven is a bit heavy...I was fortunate to have a old Workmate 425 work bench that folds/collapses, this allowed me to slide the oven out and drop down about 2 inches...reinstalling the oven I did have to use 2x4s to shim the oven level to slide it back in, with someone to assist this would not be necessary.

Step 3, remove covers to gain access to the blower and sensor

Step 4, remove the sensor

Step 5, install new sensor

Step 6, turn on the circuit breaker

Step 7, test the oven (success, Y, turn off breaker and reassemble all covers, install the oven, secure with the 4 mounting screws, turn on circuit breaker, test one more to ensure of proper operation...N, go to step 8

Step 8, turn off circuit breaker, reinstall original sensor

Step 9, remove blower

Step 10, install new blower

Step 11, turn on circuit breaker

Step 12, test oven, problem resolved, Y, go to step 13, N, continue troubleshooting.

Step 13, turn off circuit breaker

Step 14, replace all covers and reinstall oven, secure with 4 mounting screws

Step 15, turn on circuit breaker

Step 16, test, still operating properly Y, receive hugs and kisses from wife, N, do not make eye contact with wife, take dog for a long walk.
  • Cynthia from Bradenton, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench (Adjustable)
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fan blower error on oven, oven would not work or
Turn power off to oven, removed screws holding oven into cabinet, get assistance to remove oven, I used 2 dinner table chairs to set the oven on, be careful as the front of the oven is heavier than the back. Removed the back sheet metal covers, about 20 screws or so. Removed Fan motor, replaced with new fan motor, and reversed installed. Oven works great.
  • Darrell from ACWORTH, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
8 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Clear Error Code F96
Changed Fan Blower only, which cleared the Error Code F96.
Other parts have been kept as spares.
  • Salih A. Hindas / DHA from SPRNGFLD GDNS, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
7 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
F97 code
Replaced upper cooling fan and board on double oven by removing covers on top and back.
Other Parts Used:
FAN BLOWER BOARD FAN SENSOR
  • Don from BATON ROUGE, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Socket set
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

5 questions answered by our experts.
Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Michael
December 18, 2018
I am getting a f96 code and was wondering if you might know what could cause that.Thanks
For model number pk7000ej4es
PartSelect logo
Hi Michael, thank you for your question. The F96 error code indicates that you have a problem with your cooling/blower fan and that part may need to be replaced. I hope that helps. Good luck with your repair.

31 people found this helpful.

Was this helpful?
Thank you for voting!
Ian
February 27, 2019
My new upper cooling fan for GE oven model #jt3500sf3ss arrived and i noticed it doesn’t have a sensor board. Was it supposed to come with one? I noticed that this cooling fan replaces the original. Does the new version not require a sensor? Thanks.
PartSelect logo
Hi Ian, Thank you for your question. The board sensor fan is sold separately from the blower. The part number listed under your model number for the board sensor fan is PS8754576. I hope this helps. Thank you and have a great day!

5 people found this helpful.

Was this helpful?
Thank you for voting!
William
December 17, 2019
I get a notice of lower oven cooling fan error...but i don't know where to get the code everyone is talking about...do you thing just changing the fan will do it?
For model number jk3800sh4ss
PartSelect logo
Hello William, thank you for your question. Yes, if the error code is in relation to the lower oven cooling fan it should be replaced. I hope this helps.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Steven
January 20, 2022
i have a code showing F97 - is that for the lower or upper cooling fan replacement and do i need any other parts to repair ?
For model number jk5500sf6ss
PartSelect logo
Hi Steven, Thank you for your question. The F97 error code is letting you know that there is an issue with the lower cooling fan. The problem with fan may be caused by the fan motor, the wiring or the sensor that tells it when to turn on and off. You will need to inspect these parts to see which one is causing the issue. Once you have determined which part you need, and you would like to place an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!

Was this helpful?
Thank you for voting!
Related Parts:
William
April 9, 2022
F96 error, could it be just the sensor and not the fan. How to tell. Thanks
PartSelect logo
Hello William, thank you for writing. For us to locate the correct parts and repair information we will require the model number of the unit. On our site, one testimonial confirms that Fan part PS12702967 did fix the issue. " Changed Fan Blower only, which cleared the Error Code F96." If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.

Was this helpful?
Thank you for voting!
  • 1
You May Also Need ?
Model Cross Reference
This part works with the following models:
PartSelect Number: PS12702967
Manufacturer Part Number: WB26X31060
Brand
Model Number
Description
General Electric
CK7000SH1SS
Wall Oven - ELECTRIC OVEN
General Electric
CK7000SH2SS
Wall Oven - ELECTRIC OVEN
General Electric
CK7000SH3SS
Wall Oven
General Electric
CK7000SH4SS
Wall Oven
General Electric
CK7500SH1SS
Wall Oven - ELECTRIC OVEN
General Electric
CK7500SH2SS
Wall Oven - ELECTRIC OVEN
General Electric
CK7500SH3SS
Wall Oven
General Electric
CK7500SH4SS
Wall Oven
General Electric
CKD70DM2N1S5
Wall Oven
General Electric
CKD70DM2N2S5
Wall Oven - Electric Oven
General Electric
CKD70DP2N1S1
Wall Oven
General Electric
CKD70DP2N2S1
Wall Oven - Electric Oven
General Electric
CKS70DM2N1S5
Range
General Electric
CKS70DM2N2S5
Wall Oven - Electric Oven
General Electric
CKS70DP2N1S1
Range
General Electric
CKS70DP2N2S1
Wall Oven - Electric Oven
General Electric
CKS70DP2N3S1
Wall Oven - Electric Wall Oven
General Electric
CT9050EK2DS
Wall Oven
General Electric
CT9050EK3DS
Wall Oven
General Electric
CT9050EK4DS
Wall Oven
General Electric
CT9050EK5DS
Wall Oven
General Electric
CT9050SH1SS
Wall Oven - ELECTRIC OVEN
General Electric
CT9050SH2SS
Wall Oven - ELECTRIC OVEN
General Electric
CT9050SH3SS
Wall Oven
General Electric
CT9050SH4SS
Wall Oven
General Electric
CT9050SH5SS
Wall Oven
General Electric
CT9050SH6SS
Wall Oven
General Electric
CT9070SH1SS
Wall Oven - ELECTRIC OVEN
General Electric
CT9070SH2SS
Wall Oven
General Electric
CT9070SH3SS
Wall Oven
Customer Service Representative

Get in touch, we're here to help!

Open until 1am EST

Contact Customer Service