Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jerry
May 30, 2019
The dishwasher cycles thru wash, rinse, wash, rinse, wash, rinse, endlessly. Is the control board bonkers?
For model number LFBD2409LM0B
Hello Jerry, Thank you for the question. This sounds like an issue with the Control Assembly, PartSelect Number PS8689162. You can try to unplug or turn the power off to the appliance for 5 mins and see if it will reset before replacing the control. Hope this helps!
6 people found this helpful.
Was this helpful?
Thank you for voting!
Shibin
October 19, 2021
Wash, Dry, Clean lights blinking and washer won't start. Tried to re-set turning off/on the breaker. Still not working. I am thinking it is a control board issue. To make sure I had removed keypad connection from control board, turn the power on and closed the door and found no drain (or anything) is happening. Will this confirm a control board issue?
For model number FFBD2408NS5B
Hello Shibin, Thank you for the question. Yes, this would normally indicate the Control Board is defective and will need to be replaced. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Brad
October 26, 2021
Tub still full of water at end of cycle seams to be skipping over drain cycle if you push cancel cycle the drain pump dose work and removes the water but when running through a normal cycle it doesn’t want to drain possibly the main control board?
For model number FFBD2408NS0A
Hello Brad, Thank you for the question. This sounds like the Timer is skipping the cycle. The Timer for this model is built into the Control Board, so the Board will need to be replaced. We hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Donna
October 12, 2021
My dishwasher starts then stops, If I push the start button it will start then stop again. As long as I keep doing that it will get thru the cycles. Could it be the board?
For model number FFBD2408NB8C
Hello Donna, Thank you for the question. This sounds like the Door Latch is not staying engaged and may need to be replaced. We hope this helps!
WHEN THE DOOR IS CLOSED THE POWER BUTTON IS BLINKING, BUT WHEN THE POWER BUTTON IS PUSHED TO START THE CYCLE, THE WASH LIGHT IS ON AND THE POWER BUTTON IS ON , BUT NOTHING IS HAPPENING, COULD THIS BE THE CONTROL PANEL?
For model number FFBD2406NW11B
Hello Larry, thank you for your question. We have researched the model you have provided, and we would suggest the Control Board, part number PS12365196. We hope this helps!
Was this helpful?
Thank you for voting!
Richard Helms
February 1, 2022
I need the front push button control panel as well.
For model number Fdb1050reb2
Hi Richard,
Thank you for your question. The part number listed under your model number for the overlay-black is FIX1147093. If you would like to place an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
unit lights blinking simutanously light wash,hi temp, and washing however when I hit start, lights go off and unit doesnt start
For model number ffb02466nb7b
Hello Jesus, thank you for your inquiry! According to our research on model number FFBD2406NB7B, the issue is probably with the Control Board, part number PS12365196. If that is not the problem or if you have already fixed that, then the problem would be related to the Pump Motor Kit, part number PS3497737. Customer service is available 7 days a week if you need help placing an order. Glad to be of assistance!
My dish washer doesn’t come on at all could it be the board?
For model number FDB520RHBO
Hello Nicholas, thank you for your question. Yes, the issue could be the electronic board, control panel or the door switches. If the door switches have failed the unit will not show any options to start the unit when the door is closed. We would recommend testing/replacing the door latch and switches first, which is Part Number: PS6448153. I hope this helps!
Hello Charles and thanks for writing.
It certainly sounds like a faulty door latch PS6448152 and/or pump motor S3497737 check for signs of damage, and replace it if needed. We hope this helps. Please contact us anytime.
Dishwasher sometimes starts but then stops after 20 seconds, is that the board?
For model number FFBD2411NS6B
Hello Steve, Thank you for writing, Please see the URL provided https://youtu.be/q536XKIgauY. Check the Door Latch PartSelect Number PS12585637, Door Strike PartSelect Number PS2331186, Harness PartSelect Number PS11770421 or Board PartSelect Number PS12365196. We hope this helps.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Dishwasher not going through the wash cycle
First disconnect the power. Open the dishwasher door. Unscrew all of the screws except the top two screws. Unscrew the top two screws last and slide the door off. Unscrew the housing for the control board. Disconnect the wires from the control board(take a picture or mental note where the wires are positioned for reinstalling). Unscrew the control board. Put the new board in and go in reverse order until the job is complete. Good luck.
Travis from OAK PARK, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
5 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
no lights on the front of the Frigidaire dishwasher
I ordered a PS12365196 BOARD from PartSelect that arrived in 2 days, a few lights came on but still did not work, next I called back to get the PS8689162 Control Assembly, (this took another 2-3 days) this has the buttons on the front that usually light up when you set up and run the dishwasher. Still no luck so i had to try and understand this as there really isn't much more to the control of the device. Went back in, by now I can take this apart in about 5 minutes, replaced the original control board and it stared right up! Called PartSelect and a few minutes later confirmed the return of the 1st part which did not seem to work. Got to go as my email just arrived with return instructions...
Paul from CONCORD, NH
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Screw drivers
4 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The DW had no lights and would not work.
While trouble shooting the issue, noticed that all switches worked and there was sufficient power going to control board but still nothing working. Ordered new control board and with only a Phillip's head screwdriver, I was able to remove cover and control board to replace. DW works like new after the repair.
Elizabeth from LONG BEACH, MS
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wouldn't run!!
Repair man gave indication that it would cost 2-300 dollars to fix!! We looked into new and found your site. Decided to try it!! Glad we did!! Easy fix for less than $200 and it works!!! Thank you!!!
Ronald from PENN YAN, NY
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwaser just would not start. Indicator light were flashing.
Figuring the issue was the Control Board, I ordered one. ($90) When it came I installed it...SAME problem. So I took it out and reinstalled the old board and it WORKS. Apparently some connection was not right and just moving the conectors by taking them in and back out twice fixed the problem. And FYI, since it is an electric part it is NOT returnable once it s been installed!
The Fix App makes it easy to manage all your stuff in one place. Just snap a photo and we'll find and store your user manuals, receipts, and product information in one easy-to-find place!
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff