This gasket is used to seal the freezer door when closed to keep the cool air inside and the warm temperature surrounding the freezer from getting in. It is white in color. If you notice that your freezer is not shutting with ease, is not maintaining your desired temperature, or there is frost build up, it could be due to the door gasket being damaged. You might also notice that there is a leak coming from the door and this could also be caused by the gasket being worn, damaged, or no longer aligned properly. You will need to remove the existing screws before installing the gasket.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Ira W - March 13, 2024
Verified Purchase
Good replacement
Gasket works great but was slightly different than the original making it somewhat harder to install. Packaging was great gasket arrived with no kinks or deformed shaping.
★★★★★
★★★★★
Florence J - September 15, 2023
Verified Purchase
Freezer door gasket
I received the gasket and the Frigidaire repair man replaced the gasket. The gasket fitted perfectly and the repairman had no problem.
★★★★★
★★★★★
Scott D - September 8, 2023
Verified Purchase
Fairly easy and quick repair.
Replaced door gasket due to ice build up in freezer. Once installed I wasn't sure if it was going to work out due to gaps between the freezer and gasket. After I made sure the gasket sealed all the way around I left the door closed for several days and it is working just fine now.
★★★★★
★★★★★
James E - August 31, 2023
Verified Purchase
work great
working great again
★★★★★
★★★★★
Brian M - June 14, 2023
Verified Purchase
Simple enough
The part worked great it was a little tricky as you have to take the inside panel of the door off and getting lined back up is tricky but it does repair the issues of frosting.
★★★★★
★★★★★
Edward M - January 4, 2023
Verified Purchase
poor packing
I was charged $85 for shipping from Utah to California so I expected some kind of fancy packing to retain the shape; instead it came folded in a small box which caused problems installing it. I wrote a note to customer service but all I got was directions to contact tech support. All I wanted to know was why I was charged $85 for shipping
★★★★★
★★★★★
Carol E - September 16, 2022
Verified Purchase
Easy repair
It solved the freezer frosting up issue perfectly.
★★★★★
★★★★★
Corena M - May 26, 2022
Verified Purchase
Holy gasket
The part arrived in a decent amount of time but has a hole in it. I'm disappointed and my freezer still needs a gasket.
June 27, 2022
Thank you for your review. I’m sorry to hear that happened, we will be in touch soon to help fix this issue.
★★★★★
★★★★★
Mike J - January 20, 2022
Verified Purchase
an easy fix for a damaged gasket
The gasket was correct and was a very easy installation.
★★★★★
★★★★★
Mark H - November 17, 2021
Verified Purchase
Hard to install; did not finally fit; failed.
This gasket for a Frigidaire freezer was the right width and height for my model number (double-checked) but the depth was much shallower than the OEM gasket and there was no seal anywhere, plus I couldn't shut the door.
I ended up reinstalling the original gasket and used a jury-rigged stick arrangement to keep the door shut while I now order a new (and different) brand of freezer. A 7- year life is not long enough for a low-duty freezer.
This gasket was a waste of $117 and 2.5 hours of my time.
< Prev
1
2
3
Next >
Customer Repair Stories
Average Repair Rating: 3.1 / 5.0, 11 reviews.
What's this?
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Original magnetic door seal no longer sealing & showing gaps. Freezer running continuously. Getting ice buildup around door frame & inside top of freezer.
I originally ordered an aftermarket replacement seal off intranet at half the price. It came in poor packaging & crumpled in a ball when received. After install, it would not seal & worse than the old seal that was replaced. I removed poor quality seal & returned it. I then ordered the OEM seal from PartSelect. It came in proper packaging
... Read more. I kept the inside door shelving in place with two mid screws. Beginning at top I inserted sealing grove into channel of shelving working all the way around door frame. Making sure there was no crinkles or bulges at one place & it was all even. I replaced all screws ensuring not to over tighten. Close door and made sure magnetic seal pull closed to freezer & door on both sides by sliding my finger all the way around. I did not open the door for 1 hour to ensure rubber seal had taken proper shape to freezer frame. After I worked door Open/Close many times. Door seal worked perfectly every time then and now. This is a perfect example why to buy quality parts the first time.
Followed the instructions that were sent and repair was easy.
Followed the instructions
Glenn from CHAPPELL HILL, TX
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The temperature displayed on the control panel was erratic
The replacement of the Thermistor is a snap. Take out the bottom two shelves, remove the 8 screws in the back panel, pull it out. Cut the wires to the old thermistor and install the new one. There are demo's on you tube so I wont go into detail.
Unfortunately the replacement door seal was packaged with twists in it and wou
... Read moreld not lay flat on the door. I found the old seal was not the problem - but instead ice had grown between the door and the door panel so that the door would not seal properly. I reinstalled the old door seal and everything is fine now.
Gasket shipped in box, could never get wrinkles out, freezer leak, ice formed on for and freezer,. Could have saved $150.00 + by not trying gasket.
Purchased new freezer.
mary from Hallettsville, TX
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers
9 of 12 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door wouldn’t stay shut
Purchased gasket from parts plus installed it and door still won’t stay shut without duct tape plus the frost is building up really bad looking for another parts store to get problem fixed
Angela from ORLANDO, FL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
2 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Frost inside freezer.. Old door gasket leaking.
Pretty straight forward. Loosen all screws "but do not remove" pry door panel from door just enough to slip gasket behind panel. Make sure gasket is seated properly around door.. Tighten all screws snug...
Gasket may not seal right away due to being kinked from packaging, use a little heat on gasket witth hairdryer and push so
... Read moremething heavy against door over night. The gasket will straighten out over night.
Read less
Eric from SEVIERVILLE, TN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
17 of 17 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Freezer seal was leaking
Remove door remove old gasket, put new seal in dryer for 10 minutes to help it shape better then install new gasket with about 50 screws
John from LAKELAND, FL
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
5 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Hard to get under metal strip.
Took out screws completely then had to wedge gasket underneath. Gasket comes a little tangled in box should remove immediately and keep at room temp till ready to use.
Anthony from Conway, SC
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Socket set
7 of 8 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gasket old and leaking
This freezer has many screws that hold the cover on the back of the door and assist clamping the edge of the gasket in place. Be sure to just loosen the screws 3/4 the way out, use a flat head screw driver to pry the cover from the door in case over time it is stuck to the door. The new gasket will come in a creative box trying not to kin
... Read morek the gasket itself, but there will be some distortion of the gasket when you get it. Put it in the sun or in hot water. I put it in my dryer for 10 minutes. Remove the old gasket, and start at the top of the door to replace the gasket. TIPS: If the screws are backed out enough, there should not be any problem sliding the back part of the gasket under the cover. When on the sides, do not pull the gasket down to make it easier to slide the gasket underneath the cover. This will distort and lengthen the gasket so it will not fit and thin it out so it will not function well. Once the gasket is in place, tighten the screws being sure to feel along the outside edge of the gasket for any bulging that would indicate that portion of the gasket is NOT under the cover properly.
Read less
Thomas from RIXEYVILLE, VA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
103 of 110 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Freezer is 17 yrs old so needed a new gasket. The results were poor since the new gasket would not allow the door to seal.
Removed the numerous screws and took the door panel off. Cleaned and dried it. Replaced the insulation and hung the penal with 2 screws at the top and sides. Started to fit the gasket under the edge of the panel and put on the screws as I went across the top then down the sides finishing across the bottom. Perfect fit but could not get th
... Read moree door to seal at all. Went out and bought a new freezer(did I say it was 17 yrs old?!?!).
Read less
Richard from CARY, NC
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
13 of 14 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
24 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jenny
September 10, 2017
Does this seal have a magnet in it??
For model number F82U20F3W0
Hi Jenny,
Thank you for your inquiry. Most gaskets have a magnetic strip so that the gasket can magnet to the appliance when the door is closed, however this is not how the gasket will install. This particular gasket is sandwiched between the door panels. You don't have to take the door apart, just unscrew the panels enough so that you can push the gasket into place. Good luck with your repair.
27 people found this helpful.
Was this helpful?
Thank you for voting!
Jerry
August 5, 2019
What is the size of gasket
For model number 25328042804
Hello Jerry, thank you for your question. This replacement Door Gasket for your model is approximately 66 x 31.5 inches. Good luck with your repair!
20 people found this helpful.
Was this helpful?
Thank you for voting!
Carolyn
August 30, 2017
My freezer sweats really bad on front of door causing water to leak onto floor. Is that from a faulty gasket?
For model number AFFU2066DW3
Hi Carolyn,
Thank you for the question. Yes when the door is sweating it is recommend that you replace the gasket.
Good luck with the repair!
16 people found this helpful.
Was this helpful?
Thank you for voting!
Ruth
February 21, 2018
Door ajar alarm is continually going off and there is no suction when the door is shut. It used to forcibly pull and suction the door to the freezer body. Making it really hard to open the door. That is now gone. Gasket looks good and appears to seal all the way around. Freezer temps are good. There is sweating on the outside of the freezer but freezer is located outside. We have replaced the light switch and computer module. Would replacing the gasket fix this door ajar issue? Or is there some other part that helps with the suction and seal?
For model number LFFH21F7HWG
Hello Ruth, thank you for your question. If the computer module part number 297366300 has been replaced and the alarm is still sounding I would recommend replacing the gasket. The new gasket may create a better seal and may disable the alarm when the door is sealed well. I hope this helps!
15 people found this helpful.
Was this helpful?
Thank you for voting!
John
July 31, 2019
Is it recommended to remove the freezer door before replacing the gasket, just as well to leave door on? Seems like easier to remove the door, and then install gasket, thank u for ur feedback
Hi John,
Thank you for your question. Here is a link to one of our YouTube videos that you may reference on how to install a door gasket, https://www.youtube.com/watch?v=H_YGyLUT564. The refrigerator in the video may not show exactly like the one you have, but it will give you a general idea on how to install the part. I hope this helps. Thank you and have a great day!
9 people found this helpful.
Was this helpful?
Thank you for voting!
Ruth
February 21, 2018
Can a lack of suction seal cause the door ajar alarm signal?
For model number LFFH21F7HWG
Hi Ruth,
Thank you for your question. Generally that will be caused that noise to happen is because your door switch is not realizing that the door is closed. If your gasket is not sealing correctly against the cabinet and activating the switch, that could be the reason why it is beeping. If your gasket is sealing against your cabinet then it may be your door switch that is the issue. I hope that helps. Good luck with your repair.
4 people found this helpful.
Was this helpful?
Thank you for voting!
Susan
July 8, 2021
Can i get a door gasket for this upright freezer
Model 28042 Kenmore
For model number 28042 kenmore
Hi Susan,
Thank you for your question. The part number listed under your model number for the freezer door gasket is PS11770643. If you would like to place an order for it, you may order it either online or by calling our customer service line and anyone will be happy to assist you. We hope this helps! If you have any questions, please let us know.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Louise
September 18, 2022
Freezer sets on covered porch. BUT it did the same as follows even in the house. It will starts to melt when door is open, and freeze back. But even when the door is closed for long periods it just keeps building up Ice starting from the top shelf and top of inside door then keeps working it way down freezing up with Ice around all the food. Until you have to defrost it. As soon as you plug it up IT STARTS ALL OVER AGAIN ! You can hear the suction of the door closing when you first defrost it and is hard to pull the door open to put food back it. Still shuts good even when it Ices OVER. I put tape on it & have a heavy drum against door thinking it was not staying closed. It still freezes up NEVER STOPS & then freezes the door shut. Could it still be the seal ? Or something else.THANKS Louise
For model number GFU21M4AW2
Hello Louise, thank you for your question. We have researched your model and found that the issue is probably with the Door Gasket, part number PS447460. If you require assistance to place an order, please contact customer service. We hope that helps!
Will this gasket fit a freezer with the model number 25323024102?
For model number 25323024102
Hello Lynn,
Thank you for your question. Yes, this freezer gasket is compatible to your model. We hope this helps.
Was this helpful?
Thank you for voting!
Joshua
March 22, 2023
What temperature number is best to set at to avoid ice build up?
For model number Ul5000ECw4
Hello Joshua, thank you for reaching out. According to our research, the fresh food compartment should be set to 37 degrees Fahrenheit, and the freezer should be set to 0 degrees Fahrenheit. We hope this is helpful!
Was this helpful?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
